valve bonnet 中文意思是什麼

valve bonnet 解釋
閥蓋
  • valve : n 1 【機械工程】閥，活門，舌門；汽門。2 【解剖學；動物學】瓣，瓣膜；（貝）殼瓣；【植物；植物學】...
  • bonnet : n 1 （男用）無邊蘇格蘭圓帽；（兒童或婦女戴的）有帶戶外軟帽；（無邊）礦工帽；（北美印地安人的）羽...
  1. Wcc valve bonnet and internals will be manufactured with 300 series ss and / or 21 / 4 cr

    Wcc閥門的閥帽何閥內件採用300系列不銹鋼和/或21 / 4鉻製造。
  2. Wcc valve bonnet and internals will be manufactured with 300 series stainless or 21 / 4 cr material

    Wcc閥門的閥帽何閥內件採用300系列不銹鋼和/或21 / 4鉻製造。
  3. A complete list of replacement components can be found on the preceding page. bonnet assemblies and seals are interchangeable between angle and y - pattern valve bodies

    更換部件的完整清單可以在前一頁找到。閥帽組件和密封在角形和y形閥體之間可以互換。
  4. Top ( upper ) mounting type : unnecessary to unload valve from pipeline for maintenance but just by opening the bonnet for on - line maintenance

    頂裝式：閥門維修時不需要從管道拆下，只要打開閥蓋即可進行在線維修。
  5. Holding the memory stops in position, turn the ( clockwise ) down until it stops against the valve bonnet. the memory has now been set

    將記憶止動裝置保持在其位置上，順時針旋轉鎖軸環直到其停止靠到閥門閥蓋為止。記憶現在已經設置完畢。
  6. Air cylinder valve bonnet

    氣筒閥帽罩
  7. To clean : inspect or replace worn valve disc, disconnect control pipe and unscrew bonnet from valve body using blunt tool and hammer on bonnet lugs

    清洗：檢查或更換磨損的閥門閥瓣，斷開控制管道，用鈍工具和錘打閥蓋塞頂部，從閥體上旋下閥蓋。
  8. Bonnet nuts : number is dependent on valve size and class

    閥蓋螺母：閥門通徑和壓力等級不同，螺母的數量也有所不同。
  9. Install the valve bonnet. torque to 70 ft. / lbs

    安裝閥蓋。扭矩為70英尺/磅。
  10. Tightening valve bonnet is necessary to stop any leaks

    如果必要緊固閥蓋，避免任何泄漏。
  11. Tag location for gate and globe valves is typically on the valve yoke or body / bonnet flange

    閘閥和截止閥的標簽位置通常在閥門軛架或閥體/閥蓋法蘭上。
  12. Replace memory stop / lockcollar assembly into the valve bonnet

    將記憶止動/鎖軸套總成重新放置到閥蓋內。
  13. The entire valve body and bonnet, inside and outside are fully coated with a fusion bonded epoxy that offers protection against corrosion and abrasion. the wedge is fully encapsulated with a vulcanized sbr or epdm rubber. all trims are made of stainless steel and copper alloy to prevent from polluting fluid medium

    閥門內外表面採用無毒環氧樹脂粉末塗敷，閘板全包耐蝕橡膠，其他與介質接觸的零件，均採用不銹鋼和銅合金製造，具有良好的抗蝕性能，不污染介質。
  14. Bonnet studs : number is dependent on valve size and class

    閥蓋柱頭螺栓：閥門通徑和壓力等級不同，螺栓的數量也有所不同。
  15. Unitized bonnet / base design, rugged construction and 2 - ring control make the 41a safety relief valve extremely dependable in terms of pop action, seat tightness and repeatability

    採用閥蓋/基座結構，堅固耐用，雙環控制，這使得型號41a安全閥在彈起作用、閥座密封和重復性等方面特別穩定可靠。
  16. Ratings ? valves must only be used in operating conditions within the appropriate ansi pressure - temperature ratings for valve class rating and body / bonnet material ( see technical data section )

    額定壓力溫度等級?閥門只能用在規定閥門額定壓力等級和閥體/閥蓋材料的ansi壓力-溫度等級規定的應用環境中。
  17. Close the valve fully by turning the stem in a clockwise direction. tightening valve bonnet is necessary to stop any leaks

    順時針旋轉閥桿，完全關閉閥門。如果必要，則緊固閥蓋以消除任何泄漏。
  18. The valve bonnet may now be removed. there may be slight leakage as the backseat does not provide a drip - tight seal

    現在可以拆卸閥蓋。如果後座無法提供無滴漏密封，則會有輕微的泄漏。
  19. The valve bonnet may now be removed. there may be slight leakage, as the metal - to - metal backseating does not provide a drip - tight seal

    現在可以拆卸閥門的閥蓋。當金屬-對-金屬後座無法提供無滴漏密封時，可能會有點泄漏。
  20. The valve bonnet may now be removed. there may be a slight leakage, as the metal - to - metal backseating does not provide a drip - tight seal

    現在可以拆卸閥蓋。如果金屬-對-金屬後座沒有實現無滴漏密封，則可能會有輕微的泄漏。
分享友人
分享到 Line

分享到臉書