verification of the load 中文意思是什麼

verification of the load 解釋
核實貨載
  • verification : n. 1. 證實，證明，確定；核驗，驗證，核對；檢驗，校驗。2. 【法律】訴狀[答辯書]結尾的舉證說明。
  • of : OF ＝Old French 古法語。
  • the : 〈代表用法〉…那樣的東西，…那種東西。1 〈用單數普通名詞代表它的一類時（所謂代表的單數）〉 （a） 〈...
  • load : n 1 裝載，擔子；負擔；工作（負荷）量。2 （車船等的）裝載量；一馱，一車，一飛機。3 【電、機】（機...
  1. The verification results show that the model can simulate well the tidal levels, current velocities, sediment concentration, bed load transport, diversion ratio in the bifurcation section, topographic change of the north and south channels, as well as sudden siltation caused by typhoons

    大量實測資料驗證表明，該數學模型可以較好地模擬長江口地區的潮位、流速、流向、含沙量、底沙、分流比、南北槽地形變化和臺風暴潮造成的航道驟淤情況。
  2. Metallic materials - verification of static uniaxial testing machines - tension creep testing machines - verification of the applied load

    金屬材料.靜態單軸向試驗機的校正.拉伸蠕變試驗機.對作用負載力的校驗
  3. ( 2 ) 3d - fem analysis for the load - bearing capacity of the stud connector as the prevailing method to determine the shear rigidity and the limit load - bearing capacity of the shear connector is the push test, which is time consuming and laborious, in this thesis the push tesi specimen of the stud connector is simulated through the non - linear analysis module of the msc / nastran and the numerical analysis results are in good coherence with that of the practicality lev ; as a result, the shear rigidity and the limit load - bearing capacity of the stud connector can be determined by the finite element method and only a few practicality verification tests

    （ 2 ）栓釘型剪力鍵承載力的3d - fem分析針對當前剪力鍵一般通過費時費力的推頂試驗來確定抗剪剛度和極限承載力的狀況，本文利用msc nastran非線性模塊實現了對栓釘剪力鍵推頂試樣的數值模擬分析，數值計算結果與試驗結果能夠很好吻合。這使得通過有限元方法的模擬和少量實物試驗的驗證，就能確定栓釘剪力鍵的剪切剛度和極限承載力，可以大大節省時間和經費。
  4. If any detail of a generated bytecode instruction sequence is wrong, the class containing that bytecode will fail verification when you attempt to load it into a jvm

    如果生成的位元組碼指令序列的任何細節有誤，那麼把包含這個位元組碼的類裝入jvm時，檢驗就會失敗。
  5. The opinion of the eccentric load about jjg781 - 2002 digital indicating railway track scale verification regulation

    檢定規程偏載測試的一點見解
  6. Metallic materials - verification of static uniaxial testing machines - part 2 : tension creep testing machines ; verification of the applied load iso 7500 - 2 : 1996 ; german version en iso 7500 - 2 : 1999

    金屬材料.靜態單軸試驗機的校驗.第2部分:拉伸蠕變試
  7. We discussed the principle of 3d - svm and four legged circuit topology detailedly, attained the related control scheme. with the example of 15kva power system ' s inverter, the principle and derivation of 3d - svm, as well as the verification of simulation result was carried out. at last, we programmed on the digital congtrol platform and processed the light load experiment

    本文詳細介紹了3d - svm控制和四橋臂電路拓撲的工作原理並得到相應的控制方法，對該方法以15kva逆變器電源為應用實例進行了分析和模擬，並在dsp數字平臺上編程實現，進行了輕載實驗驗證。
  8. Precaution to session penetration invasion chiefly dependents on reforming web script engine, include adding ip verification, to ease the load of personnel staffs handwork programming of certification

    對session滲透入侵的預防主要在於改良web腳本解釋引擎，加入ip驗證部分，減輕開發人員手工編程驗證的負擔。
分享友人
分享到 Line

分享到臉書