waste steam 中文意思是什麼

waste steam 解釋
廢汽
  • waste : adj 1 荒蕪的,不毛的,荒廢了的;未開墾的;荒涼的。2 廢棄的,無用的;多餘的;身體內排泄的。vt 1 糟...
  • steam : n 1 蒸汽,水蒸氣,水氣,霧,蒸氣壓力。2 〈口語〉精神,精力,氣力;怒氣。3 輪船,乘輪船旅行。vi 1 ...
  1. The key to that is a so - called rankine cycle engine, which captures waste heat from the car ' s exhaust and puts it back to work to heat water, which gets converted to steam to power an electric generator, which in turn charges the car ' s battery pack

    這項技術的關鍵是被稱為「林肯循環引擎」 ,它抓住了廢熱從汽車的尾氣排出,使它重新投入工作,以熱水轉化為蒸汽,啟動電動發電機。
  2. In the third, this paper makes a survey on components of the exhausted flue gas and waste heat resource, and discusses the possibility and methods of steam generation and air preheating with the waste heat. and then, the analysis on the advantages and disadvantages of heat recovery plants with conventional steel - water heat pipes and inorganic heat - transfer heat pipes is carried out. the paper also gives a valuation about the plan and features of the design of heat recovery

    對余熱源排煙的成分和余熱資源量進行標定,討論余熱回收產生蒸汽或加熱燃燒用空氣的可行性和方法,分析常規余熱回收技術設計、採用普通鋼-水熱管和無機傳熱熱管等傳熱元件的設計余熱回收裝置的優缺點,並對余熱回收設計方案及其特點進行總體評價。
  3. This paper proposes the use of steam condensate to wash the acidulation tail gas, then to be used as wash water for washing phosphogypsum, to be returned to the crystallizer, and a calculation is made of water balance in the system, so that the discharge of wastewater and waste gas is up to standard

    本文提出用蒸汽冷凝液洗滌酸解尾氣,然後用於洗滌磷石膏的洗水,返回結晶槽,並對系統的水平衡進行計算,可以實現硝酸磷肥生產的廢水和廢氣的達標排放。
  4. On one hand one can inquire more comprehensive conditions of steel construction, industrial plant construction or of industrial boilers or on the other hand of refuse incineration plants, waste incineration plants, waste heat boilers in addition to bridge sanitation and steam boilers and steam generators, under the number + 49 203 44 98 - 314 at thyssen kloenne gmbh

    Thyssen kloenne gmbh是一家高級企業,該企業針對客戶需求製造專門的廢熱鍋爐、余熱鍋爐,橋梁整修,蒸氣鍋爐和蒸氣機,垃圾焚燒設備,工業設備製造,工業鍋爐,鋼結構。
  5. The influence concerning calorific value of municipal solid waste ( msw ) fuel upon the boiler efficiency, and the problem of steam turbine ' s suitability for variabe operation condition have been analysed by using practical calculation example

    摘要針對垃圾燃料熱值對鍋爐效率的影響及汽輪機的變工況適應性等問題,結合實際算例進行了分析。
  6. Osbl experience must include several of power generation and distribution, steam generation, instrument / plant air, cooling water, raw water treatment, waste water treatment, fire water, pressure storage, atmospheric storage, flare systems, polymer warehousing, liquid loading / unloading systems

    在osbl上的經驗必須包括幾個電力生產和配送,蒸汽生產,儀表/工廠空氣,冷卻水,原水處理,廢水處理,消防水,壓力存貯,常壓存貯,火炬系統,聚合物儲藏,液體裝卸系統。
  7. The three - wastes fluid - bed multifuel burner utilizes the characteristics of fluid - bed burning and the blow gas waste heat boiler for recovery, and burns the waste gas, ash and residue from the gasifier to produce hot flue gas, which, after dust settling in the multiple dust collector, enters the waste heat boiler to recover waste heat for the generation of high - grade steam to be used in production

    摘要三廢流化床混燃爐系運用流化床燃燒特點,採用吹風氣餘熱鍋爐回收模式,對造氣產生的廢渣、廢灰、廢氣混燃,產生熱煙氣,經組合式除塵器除塵后,進入餘熱鍋爐回收餘熱,生產高品質蒸汽供生產用。
  8. Abstract : the principle, flow sheet, automatic control and application results of the production of steam from waste heat in waste gases out of sintering circular - cooler are discussed

    文摘:介紹了利用燒結環冷機冷卻廢氣余熱生產蒸氣的工作原理、設備流程、自動控制以及生產效果。
  9. Thermax zhejiang ltd. shall be manufacturing environment friendly and energy conserving absorption chillers utilizing the waste heat, steam, natural gas etc at its state of the art world class manufacturing plant coming up in jiaxing

    特邁斯浙江公司將在具有世界級製造設備的嘉興利用廢水,蒸氣,天然氣等生產吸收式製冷機。
  10. Based on sufficient investigation of relative field at home and abroad, combined with actual state of engineering, aimed at the characteristics of low temperature waste heat power generation, under adequate consideration of economical efficiency, the thermodynamic system models on the base of rankine - cycle, which mainly consisted of evaporator, ehd condenser and steam turbine - generator group with r11 as working fluid, were constructed after comparing the current low temperature waste heat power generation systems

    文中在對國內外相關領域進行了充分調研的基礎上,結合工程實際狀況,針對低溫余熱發電特點,充分考慮經濟性的前提下,對現行的低溫余熱發電系統進行比較,選擇了以具有低沸點的r11為工質,由蒸發器、 ehd冷凝器、汽輪機-發電機組等主要部件組成的有機朗肯循環熱力系統模型。
  11. Key siemens projects in zhejiang includes ultra supercritical steam turbine power plant in yuhuan, container capacity upgrade for beilun container terminal phase iv of ningbo port, advanced imaging system for zhejiang people ' s hospital and turn - key project for the hangzhou qige waste water plant, to just name a few

    西門子在浙江的主要項目包括:玉環電廠超超臨界汽輪機組,寧波港北侖四期集裝箱碼頭集裝箱容量升級,浙江省人民醫院先進的影像系統以及杭州市七格污水處理廠的整體承包工程等。
  12. Thermoacoustic prime mover is an absolutely new type of compressor. it has n ' t any moving part so it can work for a long period without maintenance. waste steam and solar energy can be used as its heating - resources so that it has many applications especially for the places having no electricity supply

    熱聲驅動器是一種與常規機械式壓縮機完全不同的新型驅動器,它沒有機械運動部件,可使用低品位能源,具有結構簡單、運行可靠、無維修工作時間長等優點。
  13. Further, waste heat recovery boiler and steam turbine are combined to improve system efficiency, resulting combined cycle generation. main characteristics of this technology are as follows

    為進一步提高系統效率,可利用氣化系統和內燃機產生的余熱,通過余熱鍋爐和蒸汽輪機實現聯合循環發電。
  14. This essay has touched upon the following work : 1. has built up theoretic models including static mathematic models of air compressor, combustion chamber, gas turbine, waste heat recovery boiler and steam turbine which are deduced according to the feature and theory of the equipment of the object of study. upon establishment of each model based on the actual conditions, a method of multiple imitation and combination is applied to parts which have already got characteristic curves to have achieved quite accurate curves whilst the method of neural net is applied to the parts which have no characteristic curves for establishment of models

    本文進行了以下的主要工作:建立理論模型,根據對象的實際設備的特點和理論關系推導壓氣機、燃燒室、燃氣輪機、余熱鍋爐、汽輪機的靜態數學模型;根據本研究的實際情況,在建立各部件模型時,對已有特性曲線的部件,採用多項式擬合的方法,得到較為準確的特性,而對部分沒有曲線的特性,則採用神經網路的方法建立模型。
分享友人