winding method 中文意思是什麼

winding method 解釋
吹奏法
  • winding : adj. 1. 卷繞的；繞線的，繞組的。2. 迂迴曲折的，蜿蜒的。n. 1. 卷繞起來的一盤（繩索等）；卷繞動作；絡紗。2. 彎曲，紆曲；不正行為。3. 【采】卷揚，提升；【電學】繞組，繞法；線圈。
  • method : n 1 方法，方式；順序。2 （思想、言談上的）條理，規律，秩序。3 【生物學】分類法。4 〈M 〉【戲劇】...
  1. In view of the poor stop accuracy, unstability of climbing at reduced or low speed and over - winding of mine ac lift when power braking is used, a siemens all - numerical rectification device is applied in the braking system of mine lift and its control mechanism and method are described

    針對採用動力制動礦井交流提升機停車準確率差，減速與低速爬行不平穩及產生過卷的問題，將西門子全數字整流裝置應用到提升機制動控制系統，並介紹了該系統的控制原理與方法。
  2. Abstract : in view of the poor stop accuracy, unstability of climbing at reduced or low speed and over - winding of mine ac lift when power braking is used, a siemens all - numerical rectification device is applied in the braking system of mine lift and its control mechanism and method are described

    文摘:針對採用動力制動礦井交流提升機停車準確率差，減速與低速爬行不平穩及產生過卷的問題，將西門子全數字整流裝置應用到提升機制動控制系統，並介紹了該系統的控制原理與方法。
  3. Therefore, the frequency - stabilised double longitudinal modes with thermoregulation were adopted. this method was realised by winding wire with high electrical resistance on to the neck of laser tube. heating was controlled by self - organised fuzzy control method

    為此，提出了增加有纏繞于激光管頸上的電阻絲輔助加熱控制環節的自四川大學博一l :學位論文組織模糊控制雙縱模熱穩頻方法。
  4. From the measurements of cyclic voltammetry and galvanostatic charge / discharge, the composite electrode had higher specific capacitance ( 0. 84f / cm2 ) than pure mwnt array electrode ( 0. 38f / cm2 ) in the same experimental conditions. a kind of linear elementary carbon with the similar structure to carbyne was prepared by a new method. the sample appeared to be winding lines with the diameter of around 0. 2 run in the magnified image of the high resolution transmission electron microscope ( hrtem )

    掃描電子顯微鏡表徵結果顯示，聚吡咯比較均勻地附於碳納米管的表面；通過比較復合電極和純mwnts陣列電極在相同條件下的循環伏安和恆電流充放電實驗結果得知，前者的比電容（ 0 . 84f / cm ~ 2 ）明顯高於後者（ 0 . 38f / em ~ 2 ） 。
  5. The experimental tests were conducted to obtain the probabilistic statistic distribution of design variables of cfrp wound pressure vessels ( such as elastic constants, strength of lamina, winding technology parameters and the geometric sizes ). and a goodness of fit test using the kolmogorov - smirnov method was used to get the best probabilistic distribution of design random variables

    對cfrp纏繞壓力容器各重要設計變量（單向板彈性常數及其強度、壓力容器纏繞工藝參數及幾何尺寸）的隨機統計特徵進行了試驗研究，並根據kolmogorov - smirnov檢驗法，獲得各設計隨機變量的最優概率統計分佈。
  6. Test method for interlaminar shear strength of ring of filament - winding reinforced plastics

    纖維纏繞增強塑料環形試樣剪切試驗方法
  7. Based on many references form civil and abroad, the author mainly studies the measurment theory and method for flux, raising height, axial power and rotational velocity. avoiding many complicated and intermediate courses for power wastage analysis, introduces the electric measurement and using efficiency curve of motor in measureing axial power, and satisfies the automatization of the device. the paper also provides a new method, inductive winding, in measuring rotational velocity of electromotor, supplys limitations of other method in measuring rotational velocity of electromotor in water, and meet practical needs in developing diving electric pump for corporation

    作者在參閱大量國內外有關文獻，著重探討了水泵流量、揚程、軸功率、轉速的測試原理和測試方法，提出了採用電測法並結合電機效率特性曲線測量水泵軸功率，從而避免了損耗分析法中大量復雜的中間過程，滿足了試驗裝置的自動化測量要求；採用漏磁感應線圈法測量電機轉速，彌補了其它轉速測量方法對水下電機測試的局限性，適應了萊恩公司開發潛水電泵的實際需要。
  8. Shorted rotor winding is a usual electric fault of synchronous machines. based on the analysis of fault mechanism especially the magnetic characteristics of tum - to - turn short circuit of rotor windings in turbo generator, the paper studies the diagnose method, which combines the traditional method with the intelligent method, to identify the fault and the severity

    轉子繞組匝間短路是一種常見的發電機電氣故障，本文對其故障機理和磁動勢進行了分析，將傳統的方法和智能化方法相結合，對轉子繞組匝間短路的存在性和故障嚴重性進行了診斷。
  9. In conclusion, the method of adding a function layer through type winding will improve the insulating performances greatly while maintaining its original ablative performances. compared with other technical schemes, no special equipment is needed. hence, sufficient raw materials and feasible process enable its promising prospect

    通過以上研究，得到以下結論：採用布帶纏繞工藝、在防熱層內添加隔熱功能層的方案能顯著提高其隔熱性能，同時保持原有防熱套的燒蝕性能和其他物理機械性能，該方案對后續工序無顯著影響。
  10. On the basis of the magnetic circuit structure analysis for the particularity of the structure and the magnetic circuit of the double - stator hybrid direct drive motor ( dshbddm ), the mathematical formula for the important parameters - self - inductance and mutual - inductance of the winding for dshbddm was derived in detail by using the method for the simplified magnetic network model and the characteristic was analyzed

    摘要針對串聯磁路結構雙定子混合式直接驅動電動機結構和磁路的特殊性，在分析電機磁路結構的基礎上，利用電機的簡化磁網路模型，詳細推導出串聯磁路結構雙定子混合式直接驅動電動機的重要參數繞組自感與互感的數學表達式，並對其特性進行了分析。
  11. According to the demands of weapon composites underwater, such as bearing the hydrostatic pressure of 6. 0mpa, no leak and damage in two years, the leakproof method is worked out with the numerical experiments, namely adding the leakproof laminate between the winding laminates

    根據水中兵器用復合材料必須耐60mpa外水壓，在水中2年不滲漏、不破壞等一系列性能要求，通過大量的實驗確定了防滲方案，即在殼體纏繞過程中將防滲漏層加入兩纏繞層之間。
  12. Firstly, a finite element approach combining the temperature parametric method with real fictitious elements scheme was proposed for simulating the winding tension process ; secondly, in accordance with the cure kinetic and heat transfer theory, a corresponding finite element method was employed to calculate the distributions of temperature, cure degree and thermal stress fields during the cure process

    根據固化反應動力學理論和熱傳導理論，對具有金屬內襯的復合材料纖維纏繞壓力容器在固化工藝過程中瞬態溫度、固化度和熱應力場分佈及其變化規律進行了數值分析。
  13. For compensating the nonlinear error between winding current and the result magnetic field of stepper motor, the method of minimum square is adopted to fit and correct the error curve of subdivision step angle, and the subdivision precision is improved

    為了補償步進電機相繞組電流與其產生磁場之間非線性引起的誤差，採用了最小二乘法對細分步距角誤差曲線進行了擬合與修正，提高了細分精度。
  14. Considering the relations between idle load characteristics and armature winding parameters of the salient pole propulsive synchronous motor ( spsm ) with its structure, stator tooth and magnetic saturation, the analysis of numerical method for the back electromotive force calculation of spsm is given under various exciting current values

    摘要針對凸極式同步推進電機的空載特性及其繞組參數與電機結構、定轉子齒槽、磁場飽和等緊密相關的問題，分析了在不同勵磁電流下同步推進電機相反電勢的數值計算方法，提出了採用電機磁場能量微動法計算相繞組的參數，並對一臺十二相同步推進電機的繞組參數及其空載特性進行了計算和測量。
  15. 4. to get the motor ' s performance by calculation with known formulas, as a result an adjustment for the motor ' s configuration can be practised. when a combined method of altering the length of armature, the number of turns in the winding and the dimension of permanent magnet is used. 5. to get the motor ' s performance when it is driven by the power converter. finally, the calculated data are compared with the experimental measurements, so as to verify the rationality and reliability of the method

    Q採用數值分析直軸負載磁場和交軸電樞反應磁場的方法來計算，得到較為準確的結果；根據電機工作特性的計算公式計算電機性能，由計算結果調整電機的結構，而調整工作使用改變電機鐵心長度、繞組匝數和永磁體尺寸相結合的方法，這樣可以得到較為理想的結果；對變頻電源供電時電機的工作特性進行計算，以檢驗其變頻時的性能。
  16. Furthermore, it posed concrete surface treatment, smearing method, winding manner of polythene gummed tape and some critical proceedings during execution

    並詳盡的提出了具體表面處理、管道塗裝方法、聚乙烯膠帶的長纏繞方式和施工過程和應注意的事項。
  17. The thesis realizes the control exciting winding method and the best exciting in towards polarity method provided in this thesis with singlechip ( at90s8535 ) and scr hardware. it proves these methods are accurate and available through the control exciting winding test. analyzing the stator current and exciting current test curves on a salient - pole synchronous motor with 2kw - 4 poles, it solves the starting - difficulty of salient - pole synchronous motors, and improves motors " starting capability

    通過在一臺2kw 、 4極凸極同步電動機上進行異步起動試驗和分析試驗過程中的勵磁繞組電流和定子繞組電流的波形，證明了本文提出的勵磁控制線路的正確性和可行性，較好地解決了凸極同步電動機起動難的問題，同時改善了電機的起動性能。
  18. The paper discusses the work princinple of ldcsm, adopts singlechip as core control cell, puts forward two kinds of control schemes, analyzes and study the technique scheme, hardware and software design of each control system separately in detail, on the basis of the centralized winding electrifying trait and pulse stepping control method of two phase hybrid linear dc step motor ( hdclsm )

    論文在討論了直線直流步進電動機工作機理的基礎上，根據兩相混合式直線直流步進電動機（ hdclsm ）集中繞組的通電特點和脈沖步進控制方法，採用單片機為核心控制單元，提出了兩種數字控制方案，分別就每種控制系統技術方案、硬體電路、控制軟體設計等技術內容進行了詳細地分析和研究。
  19. The post research and statistics indicate that measuring the short - circuit reactance of power transformer is an effective method to estimate transformer winding deformation

    實踐證明，通過測量變壓器繞組短路電抗來判斷變壓器繞組是否變形是一種有效的方法。
  20. In this article, the following technology of the carbon fiber composite flywheel in the integrated energy - storage / attitude - control system are analyzed and the valuable achievements are achieved above the foundation of consulting a large quantity of literatures and investigation : 1. different technology method for carbon fiber composite flywheel are designed, aimed at the character of carbon fiber composite material and manufacture 2analyzes the stress of carbon fiber composite flywheels made by different technology method, hoop - winding method, symmetric ortho layers pressing method, multi - layer winding method and interference joining method, under high rotate speed, builds their static model ; and simulates their technology and shape parameter ' s affecting their stress level with i - deas f. e. m

    本文在查閱了大量國內外相關文獻及調研的基礎上，針對集成化儲能/姿態控制飛輪系統中的碳纖維復合飛輪的以下相關技術進行了研究，並取得了有價值的成果： 1針對碳纖維復合材料的特點及加工方式，設計了周向纏繞成型法、對稱正交鋪層層壓法、多層結構纏繞及過盈連接法等不同工藝方式的碳纖維復合飛輪轉子； 2針對不同工藝方式的碳纖維復合飛輪轉子，進行了高速旋轉狀態下的應力分析，建立了靜力學解析模型，並結合i - deas有限元分析軟體模擬模擬了不同工藝方式的碳纖維復合飛輪轉子的相關幾何參數及工藝參數對其應力水平的影響； 3
分享友人
分享到 Line

分享到臉書