working flow rate 中文意思是什麼

working flow rate 解釋
工作流速
  • working : adj 1 工作的，從事勞動的。2 操作的，作業的。3 工人的。4 （用於）實際工作的，任事的；使用（中）的...
  • flow : vi 1 流，流動。2 （血液等）流通，循環。3 流過；川流不息；（時間）飛逝；（言語等）流暢。4 （衣服、...
  • rate : n 1 比率，率；速度，進度；程度；（鐘的快慢）差率。2 價格；行市，行情；估價，評價；費，費用，運費...
  1. At the same time, combining the electrostatic measurement principle and the actual working conditions of pneumatic pipelines, the author puts forward the design principle in theory and finishes the devising, executing, debugging, experimenting and analyzing the experiment phenomena and results, testing the feasibility of the electrostatic sensor to be used in the measurement on the mass flow rate of the coal paniculate. furthermore, with the debugging and experimenting of the system, the author improves the electrostatic sensor and its signal collecting system gradually according to the problems, and makes the performance of the system to be enhanced remarkably

    同時，作者結合靜電測量原理以及氣力輸送管道的實際工況，從理論上提出了靜電傳感器的設計依據，完成了靜電傳感器及其信號採集系統的設計、製作、安裝、調試和實驗，分析了實驗現象和結果，驗證了靜電傳感器用於煤粉質量流量測量的可行性，並且通過系統調試和實驗，針對發現的問題對靜電傳感器及其信號採集系統不斷地進行了改進，使其性能有了顯著地提高。
  2. The quality of buffer layer and thin films was analyzed by afm, xrd, rheed and xps respectively. the effect of the experimental parameters such as carbonization time, working pressure, c source gas flow rate, carbonization temperature, different carbonization gas and substrate on the carbonization process was studied firstly. it was observed that the size of particles was increased with the increase of carbonization time and the rms was opposite, but the trend was reduced while the carbonization time was long enough ; the size of particles was increased with the increase of working pressure too, and choosing a proper working pressure could get a smooth surface ; the size of particles was unobviously changed while the gas flow rate was low, but it was notability increased with the increase of gas flow rate while the gas flow rate was high enough, and a smooth surface could be also obtained by choosing a proper gas flow rate ; with the increase of carbonization temperature, the size of particles was increased, the rms is decreased and a good single - crystalline carbonization layer could be obtained, but a rough surface was formed at a excessive high temperature ; the rms of

    對于碳化工藝，側重研究了碳化時間、反應室氣壓、 c源氣體的流量、碳化溫度以及不同種類的c源氣體、基片取向等因素對碳化層質量的影響，研究結果表明:隨著碳化時間的增長，碳化層的晶粒尺寸隨之變大，表面粗糙度隨之降低，但當碳化到一定時間之後，碳化反應減緩，碳化層的晶粒尺寸以及表面粗糙度的變化幅度變小;碳化層的晶粒尺寸隨反應室氣壓的升高而變大，適中的反應室氣壓可得到表面比較平整的碳化層;在c源氣體的流量相對較小時，碳化層的晶粒尺寸隨氣體流量的變化不明顯，但當氣體流量增大到一定程度時，碳化層的晶粒尺寸隨氣體流量的增大而明顯變大，同時，適中的氣體流量得到的碳化層表面粗糙度較低;碳化溫度較低時，碳化層的晶粒取向不明顯，隨著碳化溫度的升高，碳化層的晶粒尺寸明顯變大，且有微弱的單晶取向出現，但取向較差，同時，適中的碳化溫度可得到表面平整的碳化層;相比于c _ 2h _ 2 ，以ch _ 4作為c源氣體時得到的碳化層表面平整得多;比起si （ 100 ） ，選用si （ 111 ）作為基片生長的碳化層的晶粒取向一致性明顯更好。
  3. According the key factors we find, we bring forward a new conception : multilevel suppressor and design a new high performance suppressor whose ion - exchange membrane has bigger areas and using three electrodes including one cathode ( anode ) and two anodes ( cathode ), at the same time we fill the suppression compartment with one kind of ion exchange resin which has moderate exchange capacity. according to our experiment ' s results, we find the new type suppressor has quite high working current efficiency and suppressing capacity. in most cases, the suppressor ' s current efficiency is over 90 % ; the suppressor can transform the naoh ( concentration : 200mmol / l, flow rate : i. oml / min, conductance : over 10000 i - i s cm " ) to pure water ( conductance : 8. 9 it s cm in chapter 3, the high performance suppressor is applied in determination some trace - amounts ions in plating solution, sewage. in this chapter, we also have a research on the gradient ion chromatography

    第二章首先以xyz - 1型電化學抑制柱為例，分析了電化學抑制柱的抑制過程得出影響抑制容量的主要因素主要是抑制柱的電流效率和離子交換膜的極限電流密度，因此採用中等交換能力的離子交換樹脂作為抑制室的填料以提高電流效率，在通常情況下電流效率可達到90以上；在選用同種離子交換膜的前提下，可通過增加離子交換膜的有效面積達到提高極限電流的目的從而提高抑制柱的抑制容量，因此提出了多級抑制的概念並據此研製了共電極式高容量電化學抑制柱，該抑制柱最高可將流速為1 . 0ml / min ，濃度為200mmol / l電導率超過10000 s ? cm ~ （ - 1 ）氫氧化鈉溶液抑制為電導率低至8 . 9 s ? cm ~ （ - 1 ）的純水，並且具有穩定性高、分析結果準確等優點。
  4. The tooth shape of gear pump has important influence on machining and characteristics of pumps, such as flow rate, fluctuation rate and noise etc. first, the working principle of tatsuno combined pumps is analyzed in this article

    齒輪泵的齒形對泵的加工、性能（如：流量、脈動率、噪聲）等有很大的影響。本文首先分析了進口tatsuno組合泵的工作原理，並進一步分析了其採用一對雙圓弧齒輪的優缺點。
  5. Much works has been distributed to the development of a vacuum system to simulate the outer space and a measurement system to test the arcjet performance. ignition experiments in various operational modes have been done with argon as propellant. macroscopical working parameters including thrust, mass flow rate, voltage, current, inlet pressure and vacuity are obtained by the test measurement system and actual performance parameters including specific impulse, thrust efficiency, ratio of thrust and power and ratio of power and mass flow are calculated

    以氬氣作為推進劑，在不同工況下進行點火實驗，測量獲得了其工作推力、電弧電壓和電流、推進劑流率和弧室壓力等宏觀參數，得到了不同實驗條件下其工作的實際比沖、推力效率、推力/功率比以及比功率等性能參數，分析了推進劑質量流率、電弧功率、電弧加熱發動機電弧室結構尺寸等因素對其性能的影響，為數值模擬研究和實際的低功率電弧加熱發動機優化設計及研製提供了實驗基礎。
  6. Nevertheless, as the simulating technology involves the integrated high - techs and knowledge of computers, networks, images and graphs, multi - medias, software engineering, information processing and automated control, the simulating system is affected by its own characteristic - featured conditions, running environment and training requirements, thus yielding many problems that exist in our marine engine room simulators being currently used. for example : the mers system has poor working stability and high rate of breakdown ; its viewing device is yet to be updated, as the true aspect of the engine room can not be seen during training ; the teaching display board can not display the running state of the system with 3 - d animations, neither can it change the dynamic flow chart, etc. the afore - said problems have been greatly retarding the seafaring teaching and training, and restricting the application value of mers, as a consequence

    但是，由於輪機模擬器模擬技術綜合了計算機、網路技術、圖形圖像技術、多媒體、軟體工程、信息處理、自動控制等多個高新技術領域的知識，模擬系統受到了其特有的制約條件、運行環境和訓練要求的影響，現行輪機模擬器在應用中還存在著許多問題，如：輪機模擬器系統工作穩定性差，故障率高；視景裝置落後，訓練中見不到機艙真面目；示教板不能用三維動畫來顯示設備運行狀態，不能更換動態流程圖等。
  7. In this paper, on the basis of the analysis of gear pimp working principle, the mechanism of flow pulsation and methods of reducing flow pulsation are pulsation are studied. the computing formula of transient flow rate and the coefficient of flow pulsation are deduced. the relationship between the gear pump flow pulsation and the construction parameters of the gear is studied

    本文在齒輪泵工作原理和流量脈動產生機理的基礎上，首先從理論上推導了齒輪泵瞬時流量和流量脈動系數的數學模型，分析了齒輪泵的輸出流量脈動與泵齒輪各結構參數之間的關系，並對某型齒輪泵進行模擬分析研究，給出了齒輪泵的流量脈動分析結果。
  8. The immersion electrical heater is chiefly applied in the direct contact mode of fluid heating. it features fast heat exchange and high thermal efficiency. it has the varieties of water heater, oil heater and gas heater. its heating element power density, i. e. the power per unit of heating area of the heating element, is an important parameter of the electrical heating element, which has a direct bearing on the performance and working life. the working out of the value is a highly specialized problem, being under the influence of many factors ( media flow rate, tempt, physical and chemical properties and direction in which the medium flows past the element etc )

    浸入式電加熱器主要用於直接對流體接觸加熱的場合，具有熱交換快，熱效率高等特點，分為水用加熱器、油用加熱器、氣體用加熱器，加熱元件的功率密度：即電加熱元件單位發熱面積上的功率，它是電加熱元件極重要的參數，直接影響加熱器的使用性能及使用壽命，它的取值是一個非常專業的問題，受到許多因素的影響（如介質的流速、溫度、物理和化學性質及介質流過加熱元件的方向等等） 。
  9. In this thesis a numerical model to solve the planear 2 - d depth - integrated flow ( dif ) has been established with irregular body - fitted mesh finite volume method and explicit maccormack predictor - corrector method and applied to the study of damming caused by a bridge pier under 14 working conditions varied with the combination of different pier shape. flow rate and contraction ratio

    本論文採用非規則貼體網格有限體積法和顯式maccormack預測-校正法求解平面二維水深積分方程，對明渠水流運動的數值模擬方法進行了研究，並且應用該數值模型計算了14種不同的橋墩體型、來流、收縮比的組合工況下的橋墩壅水問題。
  10. The optimal combination among structural factors was obtained through experimental results. in addition, which experimental factor has significant influence on the exponent of flow state and flow rate of these emitters was analyzed. finally, several regression models describing the relationship between flow rate and structural parameters of flow passage were set up under the condition of certain flow passage length and 10m working pressure

    根據實驗結果分析了各因素之間的最優組合，分析了各因素對滴頭流態指數、滴頭流量的影響顯著性，並在流道長度一定的情況下，建立了10m工作水頭下滴頭流量與流道結構參數之間的模型。
  11. Under the same working pressure and flow rate, the flow passage length and cross - section area of the seven different emitters were compared. according to those results, the anti - clogging ability of emitters was analyzed and several good structural form of flow passage were obtained. in addition, regression model describing the relationship among flow rate, the length of flow passage and work pressure was set up

    比較了不同結構形式滴頭的流態指數和相同工作壓力和流量下的流道長度與流道截面積，分析了其抗堵塞性能，得出了較佳的幾種流道結構，並建立了描述滴頭流量與工作壓力及流道長度之間關系的函數模型。
  12. 1, the valve is applied to the start and break and regulation of flow rate on the pipes of medias such as water, coal slurry, mine slurry and liquid grinding material with working temperature115

    1本閥門適用於工作溫度115公稱壓力1 . 0mpa的水煤漿礦漿液體磨料等介質管路上做啟閉和調節流量用。
分享友人
分享到 Line

分享到臉書