修正轉矩 的英文怎麼說

中文拼音 [xiūzhēngzhuǎnjǔ]
修正轉矩 英文
erection torque
  • 修 : Ⅰ動詞1 （修飾） embellish; decorate 2 （修理; 整治） repair; mend; overhaul 3 （寫; 編寫） write;...
  • 正 : 正名詞（正月） the first month of the lunar year; the first moon
  • 轉 : 轉構詞成分。
  • 矩 : 名詞1. （畫直角或正方形、矩形用的曲尺） carpenter's square; square2. （法度; 規則） rules; regulations 3. [物理學] moment
  1. Tmd toque modification device

    轉矩修正裝置
  2. In the simulation work, one 1. 5kw and one 18kw induction motors ? control system were simulated and two simplified control scheme were proposed. when developing the program in tms320f240 dsp, this paper solved two practical problems : the finite - length effect and dc bias effect. finally, sensorless control system based on adaptive filter theory are tested on the platform of 1. 5kw induction motor, the results show that the scheme ? performance is good

    在模擬過程中，針對1 . 5kw和18kw異步電機進行了模擬，並在此基礎上提出兩種簡化控制方式；在tms320f240的具體編程過程中，分別對自適應濾波器的有限字長效應、直流偏置效應等非理想因素進行了修正和補償；最後，在1 . 5kw微型異步電機上進行了轉矩閉環無速度傳感器實驗，實驗結果表明了演算法完全可以達到預期的目標。
  3. The random mathematical model is described using equivalent markov equations. the time and state parameters are discrete. based on the model, the flow rate distributions along radial and average at any height can be calculated directly, moreover, the probability transition matrix of the flow can be determined via the statistic character of the random cumulate particles, and be corrected by s. cd the random theoretical model shown in fig. l, the section of the bed of tbr is divided into a series of concentric circles

    一、在常溫和常壓下進行滴流床反應器流率分佈的研究，以狀態離散、時間離散的齊次markov過程描述了滴流床在滴流區的流率分佈，建立了滴流床在滴流區流率分佈的隨機模型，根據此模型可以： 1 、可直接確定任一高度下的液體徑向流率分佈及平衡流率分佈； 2 、液體流動的概率轉移矩陣可由隨機堆積顆粒的統計特性確定，以參數s修正。
  4. The new algorithm starts from an initial estimate which is based on the hough transform, and a rectangular window is centered using the current line approximation, and a new line estimation is generated by making a total least squares fit through the pixels contained within the window. this is repeated until convergence is reached. lastly, we have suggested a new technique which may recover the motion and structure parameters of a moving object by using of 21 optical flow lines based on the optical flow fields of the feature line this thesis is the project supported by aeronautical foundation science ( no. 99f53065 ) and research center of measuring and testing technologies, and control engineering in nanchang institute of aeronautical technology ( no. 2001 - 15 )

    演算法的思路是：首先，在小區域內運用霍夫變換確定直線的初始值；其次，以直線的初始值所對應的直線為中心線，建立一個矩形框；最後，利用矩形框內所包含的邊緣點數據不斷地迭代直至收斂，從而達到進一步修正直線的坐標參數；本文基於特徵直線的光流場，即線流場，建立了一種利用21條光流線確定空間三維物體旋轉運動參數、平移運動參數以及對應的空間直線坐標的線性演算法。
  5. Aim at the dtc ' s blemish mentioned above and the direction of dtc technique development, the dissertation put great emphasis on the work as follows, with an eye to exalt dtc system function : ( 1 ) a new speed - flux observer of an induction motor is proposed to enhance the accuracy of flux observing, which is an adaptive closed - loop flux observer and different from the traditions. a new adaptive speed - observation - way is deduced out according to the popov ' s stability theories ; ( 2 ) to improve the performance of dtc at low speed operation, we have to exalt the accuracy of the stator flux estimation and a new way of bp neural network based on extended pidbp algorithm is given to estimate and tune the stator resistance of an induction motor to increase the accuracy of the stator flux estimation ; ( 3 ) digital signal processor is adopted to realize digital control. an device of direct torque control system is designed for experiment using tms320lf2407 chip produced by ti company ; ( 4 ) bring up a distributed direct torque control system based on sercos bus, sercos stand for serial real time communication system agreement which is most in keeping with synchronous with moderate motor control ; ( 5 ) the basic design frame of the hardware and software of the whole control system is given here and some concrete problem in the experiments is described here in detail

    針對上面提到的直接轉矩控制的缺陷和未來直接轉矩控制技術發展方向，本論文重點做了以下幾個方面的工作，目的在於提高dtc系統的綜合性能： （ 1 ）提出一種新型的速度磁鏈觀測器，新型的速度磁鏈觀測器採用自適應閉環磁鏈觀測器代替傳統的積分器從而提高磁鏈觀測的精度，並且根據popov超穩定性理論推導出轉速的新型自適應收斂律； （ 2 ）改善系統的低速運行性能，主要從提高低速時對定子磁鏈的估計精度入手，提出了一種提高定子磁鏈觀測精度的新思路? ?利用基於bp網路增廣pidbp學習演算法來實時在線地修正定子電阻參數； （ 3 ）採用數字信號處理器dsp實現系統全數字化硬體控制，結合ti公司生產的tms320lf2407晶元，設計了直接轉矩控制系統的實驗裝置； （ 4 ）提出了基於sercos總線網路化分散式的直接轉矩控制系統， sercos （ serialrealtimecommunicationsystem ）是目前最適合同步和協調控制的串列實時通信協議； （ 5 ）基本勾勒出整個控制系統的硬體和軟體設計基本框架，詳細描述一些實驗中的具體的細節問題。
  6. The logic control principle by locomotive computer and its control logic process are introduced. the control system for the electronic fuel injection of diesel engine on this locomotive has been introduced. the emphases is put on the way to realize the constant power control for the diesel engine by the electronic fuel injection system, and how to transfer the auxiliary power of the locomotive and how to modify the locomotive tractive effort to compensate its temperature swing as the calculation result of the tractive effort by direct torque control is dependent on the temperature

    論文第6章深入研究了機車微機控制系統的工作原理、控制流程，介紹了機車微機實現邏輯控制的方式及控制邏輯關系；介紹了柴油機電子噴射控制技術在本機車上的實現方式，重點研究了電子噴射控制系統西南交通大學碩士研究生學位論文第11頁如何進行柴油機的恆功率控制，以實現機車的輔助功率轉移，並對機車牽引力進行修正，以彌補直接力矩控制所產生的牽引力隨溫度而變化的問題。
  7. The current estimated normalized magnetic field direction, corrected for the fields generated by the torque coils

    目前經由修正轉矩線圈產生的磁場而估計到的正規化磁場方向。
  8. Using gyro measurements during periods of thruster firing, with thruster outputs, mass property identification is achieved through recursive least squares algorithms on the basis of the refined dynamics equation. the approach addresses the issue by segmenting the problem into two sub - problems which both allow closed form solution to reduce computation load

    該方法利用衛星上的陀螺輸出和推力器控制指令作為演算法的輸入，在修正的衛星姿態動力學模型基礎上，推導了衛星質量特性在線辨識遞推最小二乘演算法，將質心位置和轉動慣量矩陣的辨識解耦以降低辨識演算法的維數，減少計算量。
  9. Steel frame with welding joint easily occur brittle collapse because of having a low ductility at joints then ， a semi - rigid connected steel frame has large the energy absorption capacity which can resist dynamic loads and the using steel qualities of bracing system and joints are small so adopting a semi - rigid jointed steel frame is economical and stable but for semi - rigid connections are complex and variable ， in conventional analysis and design of steel structures ， it is usually assumed that the connections between columns and beams are either rigid or pinned the analysis of steel frames adopting the assumption can simplify the procedure of analysis and design ， but cannot precisely reflect structural practical circumstance and the errors of calculating results are large ， even ， get incorrect conclusions semi - rigid connection was referred to in chinese code for design of steel structures ( 2001 ， 10 ) ， however ， it isn ’ t specified how to apply semi - rigid joints in design in fact it cannot be carry out the purpose of the paper give a calculating method that accords practical engineering and easily put into effect worthwhile it is going to promote the development of semi - rigid jointed steel frame in design and heighten structural stability in the paper ， at first some commonly employed methods for the modeling of connection behavior are introduced richard abbott function modeling of connection is adopted for extended end plate bolted connection by the 34 test data comparing to regression analysis indicate richard - abbott function modeling of connection represents an excellent fit to test data then after a semi - rigid joint behavior can be modeled as a finite stiffness rotation spring ， base on rotation and displacement equation derive the element stiffness matrixes with semi - rigid connections where the effects ofj ointed flexibility geometric non - linearity and shear forces in the connection deformations have been considered in and fixed - end forces are modified finally, a program for calculating semi - rigid with incremental - iterative method has been

    本文的目的就是為半剛性連接鋼框架的設計提供一種既符合工程實際又簡便易行的計算方法，供規范使用過程的補充、延伸或參考；同時，也將促進半剛性連接鋼框架設計技術的發展，為提高結構安全性能、節省工程成本發揮應有的作用。本文首先介紹了常見的幾種應用較為廣泛的樑柱連接彎矩轉角關系模型，在分析比較的基礎上，選用richard ? abbott函數模型作為外伸端板連接彎矩轉角關系模型，通過對34個外伸端板連接的實驗數據與回歸分析得到的參數比較可知，經回歸分析得到的此模型參數與實驗數據符合較好。然後用彈簧表徵連接點的轉動剛度，根據梁的轉角位移方程推導出半剛性連接的剛度矩陣，在單元剛度矩陣中考慮了節點柔性、幾何非線性和剪切變形的影響，並對固端力進行了修正，最後用增量迭代法編制有限元程序進行計算和分析。
  10. Then a semi - rigid joint behavior can be modeled as a finite stiffness rotation spring. basing on rotation and displacement equation, we obtain the element stiffness matrixes with semi - rigid connections where the effects of material nonlinear, hysteresis behavior and shear forces in the connection deformations have been considered in and at the same time we modify the fixed - end forces. finally, a program for calculating the elastic - plastic earthquake seismic of semi - rigid connected steel frame structure by step and step integration of wilson -

    本文在介紹和分析半剛性連接彎矩與轉角連接關系模型的基礎上，用帶有轉動剛度的彈簧表徵半剛性連接，推導出半剛性連接的剛度矩陣，並對桿件固端力進行修正，同時在考慮剪切變形、材料彈塑性、及構件的動力滯回性能的基礎上，編制了結構彈塑性地震動力時程分析有限元計算程序。
  11. Then after a semi - rigid joint behavior can be modeled as a finite stiffness rotation spring, base on rotation and displacement equation derive the element stiffness matrixes with semi - rigid connections where the effects of jointed flexibility and shear forces in the connection deformations have been considered in and fixed - end forces are modified. finally, a program for calculating system reliability of semi - ridge steel frames with monte carlo method and finite element analysis has compiled for calculating and analyzing. by calculating results of several examples for steel frame in semi - rigid joints case show the change of joint stiffness and other kinds of factors affect the system

    接著本文在介紹和分析半剛性連接彎矩和轉角關系模型的基礎上，用帶有轉動剛度的彈簧表徵半剛性連接，推導出半剛性連接的剛度矩陣，對固端力進行修正，同時考慮了剪切變形的影響，編制了半剛接鋼結構平面框架的有限元程序bhpfl ，並在其基礎上編制了基於蒙特卡洛法的montecarlo - bhpfl有限元相結合的方法，進行體系可靠度的分析。
  12. On the basis of previous work, we developed a new data processing system by use of dsp & oop. the new system overcame the problems existed in the old data processing system successfully, such as the bug which cause program dead loop when the data is too long, and the frequency leak due to principle limit of fft filter. in addition, we eliminated the measurement error brought on by phase warp

    我們在前人的工作基礎上，利用現代數字信號處理技術和面向對象的軟體開發技術，統一了彈上黑匣子數據處理系統的操作平臺，完善了轉速、掃描角測試數據處理系統，修正了原有處理程序中的因數據長度過長而導致程序死鎖的bug ；利用有限沖擊響應（ fir ）濾波器，在濾去噪聲的同時，有效地解決了矩形窗fft濾波的頻譜泄漏問題；另外還解決了因相位偏差而導致的測試誤差。
  13. The principal contributions of this dissertation are : 1. a high fidelity and real - time rotor wake inflow model was built up. based on peters - he finite states wake theory, a new influence coefficient matrix for high speed flight was derived, the modified wake model is better suitable for the flight state with a large wake skew angle

    本模型以peters - he有限狀態尾跡理論為基礎，修正了大尾跡傾斜角時的誘導速度影響系數矩陣，並結合了王氏渦流理論，導出了旋翼誘導速度垂向分量和旋轉分量的表達式，可計算平尾、尾槳和垂尾氣動中心處誘導速度各分量。
  14. By the theory of z transformation of linear system and matrix, we proved the validation of the averaging filter method using in ietd to cancel oscillation. then we illustrate the disadvantage of using averaging filter and give a new averaging filter that we note as phase - modified averaging filter, which can reduce the disadvantage. at the end of this chapter, we study the potent of reducing the time - cost of ietd by taking account the short duration characteristics of incident impulse

    本文第二章，首先簡述了時域積分方程遞推解法（ ietd ） ，然後推導了應用於旋轉對稱體的，能夠減少計算量的ietd方法，重點闡述並應用線性系統的z變換理論和矩陣理論研究了ietd方法中遇到的穩定性問題，從理論上證明了平滑濾波技術的有效性，指出了它對計算精度的影響，並在分析的基礎上提出了新的相位修正平滑濾波方法。
分享友人
分享到 Line

分享到臉書