具重圓齒的 的英文怎麼說
中文拼音 [jùzhòngyuánchǐde]
具重圓齒的
英文
bicrenate-
It has important meaning for expending the use of double circular - arc gears in works, and bring benefit in products
對于在工程中推廣使用雙圓弧齒輪cad系統，在產品中收到實效，從而帶來較大的經濟效益，具有十分重要的意義。As a new type gear transmission, double circular arc profile bevel gearing carries out its transmission by means of meshing between convex - concave tooth profile in both of the direction of tooth trace and the direction of tooth depth, so it has advantage of high load capacity, long service life, easy forming hydrodynamic oil film between teeth as well as high quality of running - in etc. therefore, more attention has been paid to its application and research in recent years
作為一種新型齒輪傳動方式，雙圓弧弧齒錐齒輪傳動不論在齒線方向、還是在齒高方向，均為凸、凹齒廓相嚙合，因而它比一般的弧齒錐齒輪傳動的承載能力高，使用壽命長；並且在嚙合過程中兩齒面間容易形成潤滑油膜，具有良好的跑合性能，所以對它的應用和研究日益受到人們的重視。Among the results of these researches, cylindrical gears with curvilinear tooth trace have merits as follows : higher bending stress, low noise, better lubrication conditions, and no thrust forces. so this kind of gear can be considered to substitute the helical gear and herringbones
本文提出的弧齒線圓柱齒輪是一種新型齒輪傳動形式，具有傳動平穩、噪聲低、潤滑性能良好、輪齒彎曲疲勞強度大的特點，因此該齒輪可以作為斜齒輪和人字齒輪的替代品用於高速重載場合。After thoroughly analyzing the influence of each pump parameters on the gear pump performance, the paper developes the criterion for optimum gear parameters, which can be utilizied in practice easily for gear manufacturing using normal involute gear hob with two - fillet type. the conclutions studied by the paper are : 1. both the addendum coefficient and the deddendum coefficient of the pump gear should be 1. 125
以目前國內普遍使用的雙圓弧頭全齒高為2 . 5倍模數漸開線標準滾刀作為泵齒輪的加工刀具，通過對齒輪加工原理的分析，提出了欲使泵齒輪參數達到最佳，泵齒輪的齒頂高系數和齒根高系數都為1 . 125 ；對變位系數的確定應考慮到泵齒輪的根切、齒頂厚、重合度以及側隙因素；泵齒輪為避免過渡曲線干涉，必然要存在根切現象。The equation of pressure angle, width coefficient, and contact ratio are calculated and the influences of these parameters on contact are analyzed. based on ordinary involute gear, the diametral deflection principle of curvilinear - tooth
最後針對現有文獻的不足，研究了刀具壓力角、齒寬系數和重合度等參數的計算方法，並分析了這些參數對弧齒線圓柱齒輪嚙合的影響。This paper establishs a integrated system about double circular - arc gears transmission design and optimal design using go a language vb. its emphases are visible design and inspect and measure of double circular - arc gears, and optimal design using crossing mesh optimal design program, it is the development of traditional design of double circular - arc gears. speeding the course of design, shorting the period of development, advancing the quality of design
本論文利用面向對象的vb語言建立了雙圓弧齒輪傳動計算機輔助設計與優化設計系統，著重對雙圓弧齒輪的設計、校核、測量尺寸、精度與公差計算機輔助設計的工程進行了可視化設計，並調用dsp正交網格優化設計方法對設計出的雙圓弧齒輪進行優化設計，並很好地集成為一體，具有通用性，因而是對雙圓弧齒輪傳統設計的一種改進和提高。分享友人