嚙合程度 的英文怎麼說

中文拼音 [niègěchéngdù]
嚙合程度 英文
fitness
  • 嚙 : 動詞[書面語]1. （鼠、兔等用牙啃或咬） gnaw （at） 2. （侵蝕） erode
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 程度 : 1. （知識、能力的水平） level; degree 2. （事物變化達到的狀況） extent; degree
  1. The paper studies the surface geometry of globoidal indexing cam by applying the theory of conjugate surfaces and the method of coordinate transformation, presents the equations related to the main inducement curvature of the cam profiles, analysis and deduces the equations of two circumscription curves, which judge if the conjugate surface could mesh properly. some calculate examples and conclusion are given. the surface equation of the globoidal cam and conjugate equation are established

    論文首先在分析空間嚙合原理基礎上，採用坐標變換法推導出弧面分度凸輪的工作廓面方程、嚙合方程和壓力角計算公式，對弧面分度凸輪的嚙合特性進行了深入的分析和研究，對判斷曲面能否正確嚙合的依據如兩類界限線方程以及誘導主曲率等進行推導，並給出算例。
  2. Klingelnberg cyclo - palloid spiral bevel gear has construction cramped, excellent transmission quality, low noise and loaded vehavior, it ’ s the main form of gear drives in the bevel gear ’ s technology field. it ’ s cyclo - palloid system, two - part cutter head and high power gears ( hpg ), has certain technology particular than gleason spiral bevel gear. systemic analysing the manufacture principle and meshing principle of klingelnberg cyclo - palloid spiral bevel gear, for accomplishing design theory and analysis method, for enhancement manufacture precision and loaded behavior, for promotion and applied in engineering field, have important theory value and actuality meaning. main work of the paper is tooth form emulation and tooth contact analyse of klingelnberg cyclo - palloid spiral bevel gear

    克林貝格（ klingelnberg ）延伸外擺線齒錐齒輪結構緊湊、傳動性能優良、噪聲小、承載能力高，是錐齒輪技術發展的主要齒制，其連續切削法，雙層刀盤技術和硬齒面刮削法（ hpg ）相對于格利森制齒輪有一定的技術特點。系統的分析這種齒輪的加工原理和嚙合機理，對完善其設計理論和分析方法，提高加工精度和承載能力，在工程中推廣應用具有重要的理論價值和實際意義。
  3. With the research in the paper succeeded it would be certain that the helical gear pump would replace the spur gear pump now widely existed in the market and also could replace the other type of hydraulic pump in some areas, which surely greatly decrease the cost of manufacture and advance the development of technology. the importance is undisputable

    本論文研究的斜齒嚙合式低脈動齒輪泵可代替現廣泛存於市場上的直齒輪泵，並能在很大程度和范圍內替代其它形式液壓泵的作用，這對于促進機械裝備的技術進步、降低機械裝備的製造成本具有十分重要的意義，其應用前景將十分廣闊。
  4. According to the differential geometry theory, the principle curvatures and principle relative curvature of the spur gear and the fg in line contact and point contact, the tooth surface relative speed and the tooth contact interface are analyzed, whose distributing on the tooth surface are visualized by computer

    在齒面的幾何特性研究中，利用微分幾何的原理分析了圓柱齒輪和面齒輪的齒面曲率、線接觸和點接觸面齒輪傳動的主誘導法曲率以及嚙合過程中齒面的相對速度和接觸區域計算問題，並獲得有益的結論。
  5. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  6. Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance

    根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2
  7. This essay takes the method of listing equations of gears " surface directly and installing them in appropriate coordinate system to establish the mathematic model for analyzing engagement of spiral helical gear. programs use this mathematic model to make numerical computation as well as to output the contact domains diagram and the relative velocity diagram on this foundation

    本文採用直接列寫齒面方程、在適當的坐標系中安裝的方法，建立了螺旋齒輪嚙合分析的數學模型，編製程序利用該數學模型進行數值計算，並在此基礎上輸出接觸區圖和相對速度圖。
  8. In this paper, the plane double enveloping worm ( pdew ) has been researched. the motion equations have been built of it

    並應用matlab語言編制了對嚙合點的運動軌跡程序，嚙合點各分力和運動速度的變化規律曲線程序。
  9. Firstly, a simple and practical representing method of the tooth edge tangential vector is applied to replace the traditional differential formula, the simple solving technique of edge contact problem makes the geometric edge contact analysis of the complex curve surface realize. secondly, using numerical searching and mathematical programming method solves the contact directions and loaded contact problem. finally, whole numerical simulation method is provided for loaded tooth contact analysis of high contact ratio spiral bevel gears

    首先以一種簡單實用的輪齒邊緣切矢量的數學表示方法取代了經典的微分表達式，大大簡化了幾何邊緣接觸的求解，使復雜曲面的幾何邊緣接觸分析得以實現；其次又採用數值搜索與數學規劃法求解了邊緣接觸的主方向和承載接觸問題，為高重合度弧齒錐齒輪承載嚙合全過程的數值模擬提供了完整的方法。
  10. Applying the computer program developed by this paper, and choosing the real values of the gear transmission, this paper has completed more than 50 sets of calculations of the thermal elastohydrodynamic lubrication based on the non - newtonian fluid. the following conclusions can be drawn according to the computational results : 1, when the gear teeth are engaged at the pitch point, the changes of both the gear rotational speed and the load have little influence on the pressure distribution and the film shape, but they have large influence on the film temperature distribution

    應用本文研發的計算機程序，選用齒輪傳動的實際參數，先後進行了50餘組的基於非牛頓流體的熱彈流潤滑計算，所得的主要結論如下： 1 、當齒輪在節點嚙合時，齒輪轉速及載荷的變化對壓力分佈口太原理工大學碩士學位論文和油膜形狀的影響不大，但對溫度分佈有明顯的影響。
  11. Taking the meshing theory of conjugate curved surface as a foundation, utilizing array method of rotation transformation of vector, the meshing equation and contour surface equation of conical cam mechanism with swinging conical roller follower were analyzed and derived, and the calculation formula of pressure angle and synthetic curvature of the mechanism was presented, thus laid a solid theoretical foundation for enhancing the machining accuracy of conical cam, improving its processing method and achieved the integration of cam cad / cam

    摘要以共軛曲面嚙合理論為基礎，運用矢量的旋轉變換矩陣法，分析並推導了圓錐滾子擺動從動件圓錐凸輪機構的嚙合方程和廓面方程，並給出了機構的壓力角和綜合曲率的計算公式，為圓錐凸輪加工精度的提高，改進其加工方法，實現凸輪cad / cam一體化奠定了堅實的理論基礎。
  12. The main work and results are as followings. according to gear engagement principle, the math model of swing movable teeth drive is established. the engagement curve, engagement equation, relative speed between eccentric gear and movable teeth, and between movable teeth and internal gear are presented, and the gear equation of internal gear is presented

    取得了以下研究成果：根據齒輪嚙合原理，建立了基於齒輪嚙合原理的擺動活齒傳動的數學模型，推導了偏心輪激波器與活齒、活齒與中心輪內齒圈的接觸線方程、嚙合方程、相對速度和中心輪內齒圈的齒形方程。
  13. This thesis reviewed the mesh theory of plane double - enveloping worm gearing : the equations including the first enveloping equation, the second enveloping equation, contact line equations of the first enveloping and the second enveloping, boundary equations of the first enveloping and the second enveloping, the equations of relative velocity and absolute velocity

    本文介紹了平面二次包絡環面蝸桿傳動的嚙合原理基礎：第一次包絡嚙合方程和第二次包絡嚙合方程，相對速度、相對角速度方程，第一次包絡的接觸線方程，第二次包絡的接觸線方程，以及第一次、第二次包絡的一界線方程和二界線方程。
  14. Electromechanical components for electronic equipment. basic testing procedures and measuring methods. part 1 : general examination. section 3 : test 1c : electrical engagement length

    電子設備用機電元件.基本試驗程序和測量方法.第1部分:一般檢驗.第3節:試驗1c :電氣嚙合長度
  15. 4 ) combining the local synthesis method for the machine - tool setting parameters, tca and ltca, and the numerical simulation of stress procedure constructs the optimal design circle with feedback. the developed software system provides an efficient design tool for the spiral bevel gears with excellent transmission behavior, high strength and lower noise

    4 ）結合加工參數設計的局部綜合法、幾何接觸分析（ tca ） 、承載接觸分析（ ltca ）及應力過程數值模擬，構成了具有反饋的閉環優化設計迴路，並形成了相應的軟體系統，為設計嚙合性能良好、高強度、低噪聲的弧齒錐齒輪傳動提供了有效的工具。
分享友人
分享到 Line

分享到臉書