均勻流公式 的英文怎麼說

中文拼音 [jūnyúnliúgōngshì]
均勻流公式 英文
uniform-flow equation
  • 均 : Ⅰ形容詞（均勻） equal; even Ⅱ副詞（都; 全） without exception; all
  • 勻 : Ⅰ形容詞（均勻） even Ⅱ動詞1. （使均勻） even up; divide evenly 2. （分出一部分） spare
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 公 : Ⅰ形容詞1 （屬于國家或集體的） state owned; collective; public 2 （共同的;大家承認的） common; gen...
  • 式 : 名詞1 （樣式） type; style 2 （格式） pattern; form 3 （儀式; 典禮） ceremony; ritual 4 （自然科...
  1. Brings forward the basic network cell model of symmetrical blast vault and asymmetric blast vault. then studies and analyses airflow in vault of main voltage switchyard hall of xiluodu hydropower station which is far cry and large numbers of airflow conflux, brings forward concept of “ virtual embranchment ” and corresponding basic network cell model, regresses calculate expressions of flux uniformity coefficient and impedance of “ virtual embranchment ” of vault of main voltage switchyard hall of xiluodu hydropower station

    而後又採用cfd數值模擬的方法對溪洛渡水電站主變洞排風拱頂這種多股氣流匯流的長距離通道內的氣流流動進行了分析，提出了「虛擬分支」的概念和相應的網路基元模型，並回歸得到了溪洛渡水電站主變洞排風拱頂各個排風「虛擬分支」風量均勻系數以及阻抗的計算公式。
  2. Abstract : thermally induced stress and the relevant warpage cause by inappropriate mold design and processing conditions are problems that confounded the overall success of injection molding. a thermorheologically simple thermoviscoelastic two - dimension material model is used to simulate the residual stress and warpage within injection molded parts generated during the cooling stage of the injection molding cycle. the initial temperature field corresponds to the end of the filling stage. the fully time - dependent algorithm is based on the calculation of the elastic response at every time step. numerical results are discussed with respect to temperature and pressure

    文摘:不均勻的熱殘余應力及其變形是注塑成型加工中常見的工程問題之一.應用熱流變簡單材料的二維熱粘彈本構方程得到的遞推公式，數值模擬了成型中的熱殘余應力及其翹曲變形，並用數值實驗討論了溫度、壓力對注塑件殘余應力及變形的影響，發現溫度變化不均勻是注塑件翹曲變形的最主要原因，其影響遠大於壓力的作用，與工程實驗的結論一致
  3. Based on the green ' s formula and the assumption of the propeller blade ' s thin sections, a lifting - surface method of propellers with the vortex lattice and equal source panel distributions on the mean camber surface has been introduced for the prediction of steady propeller ' s hydrodynamics in this paper. an approximate kurta condition was applied

    基於creen公式和薄翼理論假設導出的升力面方法，採用在螺旋槳拱弧面上分佈離散渦、源布置方法預報均勻流場中的螺旋槳的定常性能，螺旋槳尾渦面上壓力連續性條件採用近似的kutta條件處理。
  4. The radial distribution function was introduced in order to take into account the effect of the uneven local particle concentration on the particle collision probability

    推導了高顆粒濃度氣固兩相流顆粒間碰撞概率的計算公式，引入徑向分佈函數來考慮局部顆粒濃度不均勻性對顆粒碰撞概率的影響。
  5. In order to know the relationship between gas - content and pipeline ' s pressure drop, the thesis deduces the pressure drop calculating equations based on uniform flow pattern and separating flow pattern. the equations show that pressure drop is made up of three parts, that is, friction resistance effect, gas acceleration effect and the gravity effect. and the research has shown that the gas has little effect on pressure drop. in the horizontal pipeline, the resistance effect must be overmatched the acceleration effect

    為探討加入的氣體對管道壓力的影響，本文基於分相流和均相流兩種模型分別推導了三相流管道的壓降公式，表明無論是分相流模型，還是均勻流模型，管道內流體總的壓降是由三項組成的，即摩擦項、加速項和重力項，並得出了加氣對管壓變化不大的結論，所以認為在水平管道中，要獲得有效的減阻，則要使摩擦阻力分量的減小效應大於漿體加氣的加速效應。
  6. Sewage pipe flow is hypothesized as single - phase and uniform flow, and we are used to applying the chezy formulas for designing sewer systems

    目前的污水管道設計是將污水在管道內的流動視為單相均勻流，主要用謝才（ chezy ）公式進行水力計算。
  7. The measurement and test apparatus of limiting oxygen concentration ( loc ) of combustible dusts were introduced with the loc of some conventional combustible dusts given

    根據氣體均勻混合假設，導出了採用加壓或抽真空惰化情況下惰化次數的計算方法和採用通流惰化情況下惰化時間的計算公式。
分享友人
分享到 Line

分享到臉書