峰值聲壓 的英文怎麼說
中文拼音 [fēngzhíshēngyā]
峰值聲壓
英文
excess sound pressure-
From the simulation results, we can see that, for the presented cmos preamplifier - latch comparator, its transfer delay time is 231ps, and the power dissipation is 118. 6 w
時,其回饋噪聲對輸入信號和電阻串參考電壓產生的毛刺峰值分別是6 . 35mv , 1 . 57mv ;各級子adc的總功耗為5 . 57mw 。The following results were found, i. e., the water ratio affects obviously the acoustic wave velocity of rock sample ; the wave velocity is higher in saturated rock samples than in unsaturated ones ; and it decreases gradually with the strain of samples during uniaxial compression ; and also with the lengthening holding time at 160 ; when heating the samples the acoustic wave velocity increases slightly in initial stage and comes to the peak value at 60, then decreases gradually with increasing temperature ; meantime, there is a certain temperature effect on rock samples size
實驗發現含水率對波速影響比較大,飽和巖樣的聲波傳播速度高於不飽和巖樣的聲波傳播速度;人工預制裂紋對聲波傳播速度影響不大;單軸壓縮條件下,聲波傳播速度隨應變增加逐漸降低;在同一溫度( 160 )下,波速隨保溫時間的增加而逐漸降低;在對巖樣逐漸加熱情況下,初始加熱階段波速略有升高,當溫度達到60時,巖樣波速達到峰值,之後隨著溫度繼續升高其波速逐漸下降;波速隨溫度變化具有一定的尺寸效應。Firstly it discusses the value, meaning, background and method of this topic. then it deducts the single - bubble sound pressure, spectrum of sound pressure, power spectrum. according to the real situation of traveling bubble cavitation noise around a schiebe body, the mathematical model of single - bubble collapse is selected, furthermore, the mathematical model of mass traveling bubbles without interference effect is established, and the multi - peaks and rebound phenomenon while bubbles collapse is also analyzed with statistical method
首先論證了本項研究的意義,價值,背景和方法,然後推出了單空泡輻射噪聲聲壓,聲壓譜和功率譜,針對回轉體流動泡空化噪聲的具體情況,選擇了雙指數模型作為單空泡潰滅的數學模型,進一步建立了無干涉條件下的群泡輻射噪聲的數學模型,並用統計的方法分析了空泡潰滅時的多峰值和反彈現象。After analyzed the basic principle of optimized noise reduction on tyre pattern, summarized three approaches to noise reduction. the first is trying to reduce size of single block or socket to reduce noise amplitude on time domain, the second is to adjust stripes sorting order and their interlace value to avoid noise - made by every single block - peak values on time domain overlayed and the last is to adjust ratio of blocks and sockets, ratio of stripe interval and stripe sorting order to avoid noise periodical distribution and abnormal high peak values in some frequency strip
論文第四章分析了輪胎花紋優化降噪的基本原理,總結出三條降噪途徑:在允許范圍內盡量減小單個塊或槽的大小、刻刀槽軟化花紋塊來減小噪聲時域波幅度;調整節距排列順序、花紋條之間的錯位值,使各發聲單元發出的聲壓時域波形的同向峰值錯開,避免同向峰值疊加;調整花紋塊和槽比例、節距比例、節距排列順序,盡量避免周期性分佈,使輪胎所發出的噪聲趨于白噪化,避免某些頻段的異常高峰值。In the final, we evaluated and analyzed the quality of a series of compressed images with the fuzzy image and psnr ( peak signal - to - noise ratio ) measurement. we have also made some other experiments such as add noise to the images and so on
然後用峰值信噪比和本文提出的模糊圖像度量分別對一系列壓縮后的圖像質量進行評價,並且分析了它們的評價結果,最後還進行了對圖像添加各種噪聲等實驗。Peak sound pressure
峰值聲壓分享友人