拉絲性能 的英文怎麼說

中文拼音 [lāsīxìngnéng]
拉絲性能 英文
stringiness
  • 拉 : 拉構詞成分。
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 能 : 能名詞（姓氏） a surname
  • 拉絲 : wiredrawing拉絲機 bull block; bull block; drawbench; wiredrawing machine; 拉絲模 wire drawing die
  1. Natural diamond die is one the best for the drawing of precision wires. the diamond is selected meticulously to be complete grains with good. symmetry free from any foreign substances. it is prepared with advanced powdermetallurgicaltechnology that makes the diamond with the strongest strength and antiknock property during the processes

    天然金剛石拉絲模對于各種精密線材的拉制是最好的模具之一，採用的天然金剛石是經過精心挑選的，必須是顆粒完整對稱性好，沒有雜質，又採用先進的粉末冶金技術鑲套從而使金剛石在拉拔過程中獲得最大的強度和抗爆裂能力。
  2. Jiangpai natural diamond die is one the best for the drawing of precision wires. the diamond is selected meticulously to be complete grains with good symmetry free from any foreign substances. it is prepared with advanced powder metallurgical technology that makes the diamond with the strongest strength and antiknock property during the processes

    江牌天然金剛石拉絲模對于各種精密線材的拉制是最好的模具之一，採用的天然金剛石是經過精心挑選的，必須是顆粒完整對稱性好，沒有雜質，又採用先進的粉末冶金技術鑲套從而使金剛石在拉拔過程中獲得最大的強度和抗爆裂能力。
  3. Test methods for tensile properties of carbon fiber multifilament

    碳纖維復絲拉伸性能試驗方法
  4. Energy consume, electric strength, insulation resistance, ground conductivity, leakage current, microwave leakage, power input, normal temperature, humidity treatment, glow wire, horizontal flame, vertical flame, tracking, ball pressure, rainproof, water splash, dustproof, salt fog, endurance, motor load test, cord flexing, cord pulling, pull & torque test, lamp replacement, construction check etc

    能耗、電氣強度、絕緣電阻、接地連續性、泄漏電流、微波泄漏、功率、溫升、濕熱試驗、灼熱絲、水平燃燒、垂直燃燒、漏電起痕、球壓試驗、防雨淋、防濺水、粉塵、鹽霧、耐久性（壽命）試驗、電機負載試驗、電源線彎折、電源線提拉、拉扭力測試、燈頭互換性、安全結構檢查等。
  5. The stretchability is im proved with the reduction of nitrogen content in steel

    鋼絲拉拔性能隨鋼中含氮量下降而有所改善。
  6. Abstract : the contrast experimental trials of three refining processes are car ried out for ladle bottom bubbling with nitrogen, nitrogen - argon or argon. the results show that the nitrogen content in steel has an important influence on the stretchability of steel wire

    文摘:進行了鋼包底吹氮、底吹氮-氬和底吹氬三種精煉工藝對比試驗，結果顯示，鋼中對鋼絲拉拔性能影響顯著。
  7. The cable seals are high security cable seal for use in transport applications, suitable for truck trailers / valves / railroad cars / containers and so on, decoration / printing : laser printing or hot stamping

    鋼絲封，鋼絲長度可根據客戶要求定製，並可運用電腦激光及熱燙印技術刻印公司標志及序列號，價格實惠，抗拉力好，安全性能高。
  8. Aluminium and aluminium alloys - drawn wire - mechanical properties

    鋁和鋁合金.冷拉絲材.機械性能
  9. Test method for tensile properties of carbon fiber strands

    碳纖維復絲拉伸性能檢驗方法
  10. Abstract : the fragile raw silk finished with softer or not and the normal raw silk are warped on the same beam and weaved. the number of end breaking and the tension of warp of different raw silk during weaving, as well as the tensile properties and dyeing behavior of fabric are compared and analysized. the results show : if the fragile raw silk is finished with softer, the number of end breaking during weaving will be obviously decreased, and the strength of fabric will be increased slightly, but the color deviation will be existed compared with the fabric made from normal raw silk

    文摘:將正常生絲、脆弱生絲、經柔軟劑處理的脆弱生絲一起作為經絲上機織造，比較它們織造過程中斷頭、張力情況，並對織物的拉伸性能、染色性能作對比分析，結果表明：脆弱生絲經柔軟處理后斷頭次數明顯減少，織物強力有所增加，但與正常生絲一起染色存在色差。
  11. The intention of this paper is to develop a set of testing system, which has high efficient and reliable performance and advanced technology. it is applied in testing extrusion pressing of new type elevator wire rope tie - in in its making process and tensile strength, fatigue strength of tie - in. then to test the validity of design theory of the new type tie - in by analyzing the testing data and grope for new theory on and on

    本課題研究的目的是開發一套高效可靠、技術先進的測試系統，用於測試新型電梯鋼絲繩繩頭製作過程中的擠壓力、以及繩頭本身的抗拉強度和疲勞強度性能，然後根據測試數據來驗證新型繩頭設計理論的正確性，並不斷進行新理論的探索。
  12. The influence of the melt transfer temperature, spinning temperature, temperature and speed of quench air, the 1st hot rolls temperature, the 3th hot rolls temperature, drawn ratio on dying property of melt direct spun fdy were discussed

    摘要主要就熔體直接紡fdy生產過程中熔體輸送溫度、紡絲溫度、側吹風溫度、風速、第一對熱輥溫度、第三對熱輥溫度、拉伸倍數等因素對染色性能的影響進行探討。
  13. Abstract : coagulation and stretch are two crucial working procedures during precursor fabrication, which play important roles in precursor structure and performance. the fiber tensile strength is affected by concetration, temperature and minus stretch during coagulation, while the fiber structure and performance are obviously influenced by stretch temperature, medium and ratio

    文摘:凝固成形和拉伸是原絲生產過程中兩個十分關鍵的工序，它們對聚丙烯腈原絲的結構和性能有著重要的影響.纖維的拉伸強度在凝固成形過程中受到凝固浴濃度、溫度和負拉伸的影響，同時在纖維的拉伸中拉伸的倍數、溫度和介質等也影響著纖維的結構和性能
  14. While polyester fiber is subject to different draw ratio and heating temperature during high speed spin - fling, its original molecular orientation and crystallinity of polyester fiber are changed

    摘要聚酯在高速紡絲過程中，施以不同的拉伸倍數與溫度，會造成纖維結晶度與取向度的變化，從而影響纖維的物理性能。
  15. When polyester fiber is subject to different draw ratio and heating temperature during high speed spinning, it will result in changes of the original molecular orientation and crystallinity of the fiber, thus affecting its physical properties

    摘要在高速紡絲過程中對聚酯施以不同的拉伸倍數與溫度，會造成纖維結晶度與取向度的變化，從而影響纖維的物理性能。
  16. Testing method for drawability of synthetic filament yarns

    合成纖維長絲拉伸性能試驗方法
  17. Because of the former anchorage systems designed according to matching 1860mpa strength strands in the beginning of 90 ", they can not be suitable any more for the super strength strands with 2000mpa. therefore, some accidents occurred such as strands sliding and broken when tensioning. in addition, the advantages of the new materials as their high mechanics performance are not be used completely as the prestressing structures was designed as per the 1860mpa strands, which will result in the waste of materials, in view of the above - mentioned facts, by means of analyzing the development of anchorage systems home and abroad, in connection with the characteristics of the super strength strands ( 2000mpa ), this topic made a research on hvm15 anchorages by theoretical calculation and finite element analysis, and also on the manufacturing process and test

    隨著預應力技術的發展和冶金工業冶煉技術的不斷進步，預應力鋼絞線的強度不斷提高，由原來1470mpa提高到1860mpa ， 90年代末期已出現了2000mpa超高強鋼絞線，而原來的是在90年代初期按抗拉強度為1860mpa的鋼絞線標準設計的，因此，原有的錨具已不能適應現有超高強度2000mpa的鋼絞線強度要求，在工程中出現了斷絲滑移現象，同時，在使用和設計時仍按1860mpa鋼絞線的指標進行設計應用，沒能充分發揮材料的力學性能，造成材料浪費。
  18. Test method of mechanical propertes of mortar for ferrocement - test of tensile splitting strength

    鋼絲網水泥用砂漿力學性能試驗方法劈裂抗拉強度試驗
  19. Finally, it is realized preliminarily that the fabrication of hollow fibers with sic films, which concludes the process of fiber - drawing and coating, can be done in an organic whole with modified chemical vapor deposition ( mcvd )

    最後，利用改進化學氣相沉積法（ mcvd ）方法，對具有sic內膜的空芯傳能光纖的內層鍍膜、拉絲一次性完成進行了探索。
  20. A study on drawing properties and their dependent factors of low - carbon high - strength dual - phase steel wire

    低碳高強度雙相鋼絲的拉拔性能研究
分享友人
分享到 Line

分享到臉書