接縫寬度 的英文怎麼說

中文拼音 [jiēféngkuāndù]
接縫寬度 英文
joint gap
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 縫 : 縫名詞1. （接合處） seam 2. （縫隙） crack; crevice; fissure; slit
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 接縫 : seam; jugum; joint; kiss; unwelded joint接縫刨 jointer; 接縫構造 seam construction; 接縫灌漿 joint grouting
  1. A specialty foot for easy application of ribbons up to 7. 6 mm wide. also may be used to attach sequins

    對于緞帶裝飾應用，設計的一個專業壓腳，縫合寬度高達7 . 6毫米。同樣，可以用來連接亮片。
  2. Thermosetting powder coating of low - temperature curing type is a newly - developed powder coating which is used on the things that are not suitable for high - temperture baking. this type of powder coating opens up wider application by lowering curing temperature to 108 - 130. it can be used for surface coatings on such things as flaw detectors, auto water tanks, springs, electrical appliances with coils, instruments, equipment with tin welding seams. it can also be used on the products made of aluminum and magnesium materials, glass, plastics and wood etc

    低溫固化型粉末塗料是針對那些不宜高溫烘烤的產品，而最新研製的新品種，它不僅具備一般粉末塗料的特徵，而且可以把固化溫度降低到108 - 130 ，從而拓寬了粉末塗料的應用領域；適用於擦傷機械、汽車水箱、發動機、彈簧、線圈電器、儀器儀表、錫焊條接縫設備、鉛鎂材質、玻璃、塑料、木材等製品的表面塗裝。
  3. The reduction factors derived from curve fitting based on calculation results by the finite element program ( ansys ) considering all kinds of damages such as cutouts, corrosion, cracks, denting, initial deflection and residual stress are introduced to modify the effective width of perfect panel in the present paper

    本文考慮板中可能存在孔洞、腐蝕、裂縫、局部撞損和初始焊接變形或殘余應力等損傷和初始缺陷，對不同的損傷形式用有限元程序（ ansys ）進行大量的計算，通過曲線擬合的方法引入折減系數對完好板格的有效寬度進行修正。
  4. Seal the shipping container with either two inches ( 5. 08 cm ) or more width of pressure - sensitive or nylon - reinforced tape or with 60 - pound, three inch ( 7. 62 cm ) wide water - activated reinforced tape. close the box securely, applying three strips of tape to both the top and bottom of the box, so the middle and two edge seams are sealed

    08厘米）或更寬寬度的感壓或尼龍加強膠帶，或者使用60磅、三英寸（ 7 . 62厘米）寬的水活性強力膠帶，密封運輸容器。在包裝箱的頂部和底部貼上三條膠帶，牢固地合上包裝箱，這樣中間的接縫和兩條邊沿接縫就已經密封了。
  5. The influence of stress ratio on maximum crack width of specimens is obvious, and the larger the stress ratio is, the longer the fatigue life is, it can influence the mechanical property of specimens directly

    應力比對試件梁的最大裂縫寬度影響顯著，應力比越大，疲勞壽命越長，直接影響試件梁在疲勞荷載作用下的性能。
  6. In addition, the calculating methods about the gap of the connectors and the maximum width of crack are discussed in the thesis

    另外，作者對組合梁剪力連接件的設計理論及組合梁最大裂縫寬度計算方法作了逐一地探討。
  7. Secondly, according to the basic theory of the general spectrometer, in this paper we discuss the fundamental, the compositions and the characters of tcecs. we analyze the main influencing factors for resolving power, such as the dispersion of the x - ray on the detection circle, spectra location error and the aperture width etc. and we put out the ways to resolving the problems

    接下來，本文根據經典光譜儀器的基本理論，著重討論了雙通道橢圓彎晶譜儀的基本原理，及其基本組成和基本特性，並從x射線波長在探測圓上的彌散度、光度參數與探測角之間的關系、狹縫寬度等方面對譜儀的精度和解析度的影響作了一定的分析，並提出了解決問題的辦法。
  8. 7 seam must be the correct width as per original spec sheet

    接縫寬度必須按原規格資料。
  9. To adapt the width of welding lines and improve the welding quality, adding swing to the moving on theoretical center track is put forward with the actual welding process synthetically thought of. circle swing mode and. sine swing mode are discussed as typical ones and the equations of moving tracks are established

    為了適應焊縫的寬度，提高焊縫的質量，並結合焊接過程的實際情況，確定了在理論中心軌跡的基礎上添加附加擺動，討論了圓擺動和正弦擺動兩種典型模式，建立了運動軌跡的方程。
  10. Geotextiles. tensile test for joints seams by wide width method

    土工織物.大寬度法進行接頭接縫拉伸試驗
  11. The welding speed have evident effection on weld depth and weld width, when welding speed is added, both weld depth and weld width will decrease, for the inputed heat per time is limited

    焊接速度對焊縫厚度和焊縫寬度有明顯的影響，當焊接速度增加時，焊縫厚度和寬度都大為下降，這是因為焊接速度增加時，焊縫中單位時間內輸入的熱量減少。
分享友人
分享到 Line

分享到臉書