接觸型轉速計 的英文怎麼說
中文拼音 [jiēchùxíngzhuǎnsùjì]
接觸型轉速計
英文
contact tachometer- 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
- 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
- 轉 : 轉構詞成分。
- 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
- 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
- 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
- 轉速 : speed; revolution; rotation rate; speed of revolution; rotating speed; rotational speed轉速指示器...
-
Based on the theories of gear engagement, contact analysis, friction and heat transfer, a three - dimensional finite element model of gear tooth was established to investigate temperature distributions and variations along the contact path over a range of applied loads and operating speeds with consideration of lubrication conditions. sensitivity analysis of surface temperature to gear configuration, frictional heat flux, heat transfer coefficients, and oil and ambient temperature was conducted and the major parameters influencing surface temperature were evaluated
本文基於齒輪嚙合原理、輪齒接觸分析、摩擦學和傳熱學，以有限元分析方法和理論分析計算相結合為手段並以實驗測量結果作為參考，建立了適用於工業應用並具有較高計算精度的高速齒輪傳動輪齒溫度分析的模型和方法，系統地分析了輪齒本體溫度的大小和分佈以及齒輪幾何、載荷及轉速和潤滑冷卻條件等對輪齒本體溫度的影響。According to the different work conditions, analysis of the bearings ratio of revolution and rolling were inverted from the slipping of the bearing
針對實際生產中工況的不同，分2種情況建立高速角接觸球軸承分析計算模型，並將高速角接觸球軸承的旋轉打滑分析轉化為旋滾比的分析。In the test, choose the angle contact bearing as test bearing, and work in the different position of spindle system, then test the temperature and vibration of the bearings in different speed and different loading, and analysis the data to verified the mathematics models
首先根據理論計算，選用適用於高速運轉的一組角接觸球軸承，各軸承處在軸系中不同位置，然後通過試驗分別對各軸承的工作溫度和軸系振動量進行測量，最後對數據進行分析，通過試驗驗證前面所建立的數學分析模型的正確性。Then the complete simulink simulation model of soft cut - in system is established. what is more, an effective control strategy of soft cut - in unit that the cut - in rotate speed of wtg and scr phase - shifting rule should be adjusted in accordance with the rotate acceleration of rotor is put forward. on the basis that the simulation model is validated, the simulation and analysis of direct cut - in and soft cut - in process of wtg are carried out, which aims at supplying necessary referential material for the r & d of soft cut - in unit
本文以軟並網裝置主電路的分析與設計?軟並網控制系統的建模與模擬分析?可控硅移相觸發軟並網控制電路的設計為主線，首先進行了軟並網裝置主電路部分的分析與設計；然後建立了雙繞組風電機組的完整模擬模型，在對模型進行驗證的基礎上，提出了有效的風電機組軟並網控制策略，即機組並網轉速與可控硅移相規律應隨電機轉子加速度進行調節，並進行了風電機組直接並網與軟並網過程的模擬分析，得出了相應的結論，為軟並網裝置的研製提供了必要的參考依據；最後設計了軟並網系統的可控硅移相觸發控制電路的硬體與軟體的實現方案，並提出了系統硬體與軟體的抗干擾措施，重點闡述了主要軟體模塊的實現方案。分享友人