接觸電位差 的英文怎麼說

中文拼音 [jiēchùdiànwèichā]
接觸電位差 英文
contact drop
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 觸電 : get an electric shock; electric shock
  1. It creates the model of layer soil by using the cdegs software, analyses the resistance error which is measured by traditional three - poles way, measures the grounding grids resistance and soil resistance rate of hejin power plant, creates the electromagnetic model of layer soil and grounding grids model of hejin power plant, calculates the step voltage > touch voltage n voltage distribution of earth surface in fault of hejin power plant. in the end, it compares the measuring value and calculating value of grounding grids resistance in hejin power plant

    本文利用cdegs軟體建立分層土壤接地模型，對傳統三極法測量接地電阻誤差進行分析；對河津電廠接地網接地電阻和土壤電阻率進行測量；建立河津電廠分層土壤電磁模型和接地網模型；計算河津電廠接地網電阻和事故狀態下跨步電壓、接觸電壓和地表電位分佈；最後對河津電廠接地網電阻實測值與計算值進行比較分析。
  2. With the mathematic model of tracking beam current by velocity, real - time tracking can be obtained ; with current simulation controlling transducer and subsection linearity, precision of velocity ( error in ? 1 % ) is triumphantly can be controlled ; with inspection of the pulse numbers of switches, the position of all vehicles are checked to eliminate the error of calculating distance between all ones

    通過建立速度跟蹤束流的數學模型，較好地解決了速度跟蹤束流的實時性問題;通過採取用電流模擬量控制變頻器和分段線性處理的辦法，成功地解決了速度精度問題（誤差在士1 %內） ;通過檢測接近開關觸發的脈沖數，適時校核所有小車位置，消除各車之間距離計算誤差，從而很好地解決了距離累計計算誤差。
  3. The research about the non - invasive inspection of pcb that is based on ir image is introduced. the detection principle, the components of hardware and software are introduced in this paper. some key technical problems and the project of software are presented in detail : graphics of user interface ( gui ) of the projection, gray scale transformation ( gst ), image contour extraction through edge detection algorithm based on the approaching contour optimization, image registration based on corner detection, the position of hidden trouble pcb through add - minus algorithm image

    本文介紹了利用紅外圖像對印製電路板進行不接觸式故障檢測的系統研究，主要介紹了本系統的檢測原理，硬體組成及軟體的製作，其中詳細地介紹了軟體的製作過程以及其中的幾個關鍵部分：本系統的人機交互界面；圖像的灰度轉換；基於最優輪廓逼近的邊緣提取演算法進行輪廓提取；基於角點檢測的圖像配準；用差影法得到故障電路板的故障隱患或故障部位。
  4. At the same time, the method of disposal phase shift of ct by compensation is introduced. then the analysis and statistic of electrical power quality, the control scheme and compensating amount of capacitor for reactive power compensation are analyzed respectively. and in the paper, the control with a / y and the switch with ac contactor and solid state switch is valid measure not only for improving operate level economically and amending electrical power quality but also for avoiding of replacing switch frequently and decrease economic loss

    然後對現有的演算法進行了詳細的分析、比較，篩選出既能滿足硬體要求又可降低投資、保證精度、簡化軟體的方案，確定了準同步采樣的方案，並通過對準同步采樣誤差的分析，提出了一種從45開始采樣，從而提高精度的采樣數據處理辦法，同時，對于電流互感器相位漂移提出了一種補償辦法，接著對裝置中電能質量分析與統計以及無功補償中電容器的補償量、投切原則也作了相應分析，其中對于無功補償採用y混合接線，並利用交流接觸器和固態開關共同投切電容，不但提高了經濟運行水平、改善了電能質量，而且有效的避免了頻繁更換開關，減少了經濟損失；最後，設計了裝置的硬體電路並繪制了相應的軟體流程圖。
分享友人
分享到 Line

分享到臉書