接觸電壓降 的英文怎麼說
中文拼音 [jiēchùdiànyājiàng]
接觸電壓降
英文
contact drop- 接 : Ⅰ動詞1 (靠近;接觸) come into contact with; come close to 2 (連接; 使連接) connect; join; put ...
- 觸 : Ⅰ動詞1 (接觸) touch; contact 2 (碰; 撞) strike; hit 3 (觸動) touch 4 (感動) move sb ; sti...
- 電 : Ⅰ名詞1 (有電荷存在和電荷變化的現象) electricity 2 (電報) telegram; cable Ⅱ動詞1 (觸電) give...
- 壓 : 壓構詞成分。
- 降 : 降動詞1. (投降) surrender; capitulate 2. (降伏) subdue; vanquish; tame
- 接觸 : 1. (交往) come into contact with; get in touch with 2. (沖突) engage 3. (挨上; 碰著) contact; touch
- 電壓 : voltage; electric tension; electric voltage
-
The low insertion loss is achieved by optimizing the transistor widths and bias voltages, by minimizing the substrate resistances, and by dc biasing the transmit and receive nodes, which decreases the capacitances while increasing the p1db
通過優化mosfet的柵寬及偏置電壓可以降低插入損耗。在版圖設計中通過增加襯底接觸降低襯底電阻,從而減小插入損耗。另外,為接收和發送端提供直流偏置可以降低p1db 。In famous constructions and key projects such as capital international airport, sanxia three gorges hydropower project, nanjing metro subway, qingdao good - world sea palace, jinan railroad sub - bureau, suzhou amusement park, beijing 1st heating power plant, china 2nd autombile plant, xian peace villa, our products continue to operate safely
其技術性能指標達到目前國內同類產品的領先水平,其空載損耗比s11型配電變壓器的空載損耗降低60以上。同時,由於本產品採用全密封結構,絕緣油和絕緣介質不與空氣接觸,因而可在潮濕的環境中運行,是城市和農村配電網路中理想的配電設備。The pt secondary loop voltage drop is a changing amount and has the characteristics of indirection and certain randomness. the second, according to the cause of pt secondary loop voltage drop, the different methods to reduce the pt secondary loop voltage drop were analyzed and the conclusions are draw as below : 1. changing bigger section wire and maintaining the connector plugs regularly can reduce the pt secondary loop voltage drop effectively, but ca n ' t guarantee which meets the relevant rules
首先,通過對電壓互感器二次壓降的形成機理進行分析,得出以下關於二次壓降的相關結論: 1 、電壓互感器二次壓降等於二次迴路阻抗和迴路電流的乘積; 2 、電壓互感器二次迴路阻抗分為元器件自身阻抗和接觸阻抗兩部分,且接觸阻抗佔主要部分,從而使得電壓互感器二次迴路阻抗具有動態特性,而且具有一定的隨機性; 3 、電壓互感器二次迴路電流與二次負荷和迴路阻抗大小相關,因而二次迴路電流也是變化的; 4 、電壓互感器二次壓降是一個變化量,且具有單向性和一定的隨機性。It will effect the system in safety and running economy directly > test of tradition past the method is an usage to give or get an electric shock the bridge method or direct current to press to decline the method to proceed to measure, and the electric current for producing of is only in the ma class which ca n ' t broke through the oxidize surface
高壓斷路器是電力系統中最重要的控制和保護設備之一,它對系統的安全、經濟運行有著直接的影響。以前傳統的測試方法是使用電橋法或直流壓降法進行測量,所產生的電流僅在ma級,不能擊穿觸頭氧化膜。The principle of ac - dc - ac locomotive is that transformer transforms the high single - phase ac voltage from contact system to lower ac voltage first, then rectifier transforms this ac voltage to steady dc voltage, finally converter transforms this dc voltage to three - phase vfvv ac voltage as the voltage source for asynchronous machine
交?直?交型電力機車系統的原理是:先將從接觸網獲得的單相交流高電壓經變壓器降壓后,再經整流器變換為平穩的直流電壓,直流電壓經逆變器變換為三相交流電壓,供給機車輪對上的牽引電機。The program fearpv is applied to 3 - d transient sealing analysis of nuclear pressure vessel during the total process, including bolt pretensioning process, heating and compression process, thermostated heating and constant pressure process, and the cooling and decompressing process. according to the analysis and computational results in this thesis, although the actual structure and work conditions of the pressure vessel in nuclear power station are much more complex than that of the pressure vessel model, the program fearpv still can get quite good convergence on the plasticity and
由本文分析計算可知,雖然電站核壓力容器的結構及計算工況較壓力容器模擬體復雜得多,然而反應堆壓力容器瞬態密封有限元分析程序對塑性迭代和接觸迭代仍具有很好的收斂性,數值穩定性好,得到的結果具有良好的規律性,在升溫、升壓、恆溫、恆壓、降溫和降壓等過程中其規律和壓力容器模擬體基本相似。In the approach, non - load machine switch is replaced by scr controlled by mpu to regulate the temperature. this control precision is greatly improved, and at the same time parameters can be automatically stored and displayed during the manufacturing process, it also included some other auxiliary controlling functions, such as over - temperature alarm, work piece input or output reminding, etc. the fuzzy pid control algorithm consists of fuzzy control and digital pid adjustment
針對鹽浴變壓器只能進行無載分接、有級調節的問題,本方案採取在變壓器原邊串接晶閘管的方法,將手動轉換的溫度控制,即無載分接開關機械觸點調節電壓改為單片機自動控制晶閘管的導通,將手動控制溫度改為模糊pid控制,從而提高了控制精度,降低了工人勞動強度。分享友人