摩擦泵 的英文怎麼說

中文拼音 [mócābèng]
摩擦泵 英文
friction pump
  • 摩 : 摩構詞成分。
  • 擦 : 動詞1 （摩擦） rub 2 （用布、 手巾等摩擦使干凈; 揩拭; 抹） wipe; scrub; clean 3 （塗抹; 搽） spre...
  • 泵 : 名詞（吸入和排出流體的機械） pump
  • 摩擦 : 1 （互相接觸的兩物體作來回相對運動） rub; chafe 2 [物理學] （相互接觸的兩物體在接觸面上發生阻礙相...
  1. Based on the ostwald - de waele equation, the leakage characteristics of power - law transmitted by helical gear pump are researched, and the leakage model of power - law in the clearence is founded, and - the velocity distributing and the leakage capacity are worked out by the boundary condition. the power loss of leakage is got through the clearence leakage capacity, and the friction power loss is attained by the velocity distributing. the mathematic calculation model

    利用冪律流體本構方程，首次對聚合物流體在斜齒齒輪泵中的漏流特性進行了研究，建立冪律流體在間隙中的泄漏模型，利用邊界條件求出速度分佈及泄漏量；由間隙泄漏量得到漏流損失功率，由速度分佈得到流體摩擦功率損失，並得到間隙最優解的數值計算數學模型，同時給出實例及數值計算結果。
  2. The paper analyses the stress and relative motion of piston / cylinder and swash plate / slipper matching pairs in water hydraulic pisto n pump, based on which the proper experimental research method is determined

    對水壓柱塞泵柱塞、滑靴摩擦副的受力和相對運動形式進行了分析，確定了摩擦副合理的試驗研究方法。
  3. Aim of this study was to meet the need for development of tribological parts in pumps. at room temperature tribological properties of different sliding pairs of silicon carbide and alumina - based ceramics were tested using a laboratory tribometer in the ring - on - plate geometry under reciprocating sliding linear contact in different media, such as distilled water, aggressive media and air

    本文針對目前泵用摩擦零部件材料發展的需要，在實驗室摩擦磨損試驗機上研究了按環/塊線接觸方式作往復運動條件下的碳化硅和氧化鋁基陶瓷材料摩擦副在水、化學腐蝕性介質作潤滑劑和無潤滑時室溫下的摩擦磨損特性。
  4. As one of the four important parts of water hydraulic axial piston pump, the design of sliding shoes friction matching mainly takes hydrostatic bearing

    作為水壓軸向柱塞泵的四個關鍵組件之一，滑靴摩擦副的設計主要採用靜壓支承的方法。
  5. Zhou shi ? yu, duan zhan ? xu. experimental investigation of gap of port plate / cylinder block in axial piston pump j. chinese hydraulic & pneumatic, 1986, 3 : 1214

    許耀銘.軸向柱塞泵滑靴和配流盤摩擦副的設計與實驗研究j .液壓與氣動， 1977 ， 2 ： 312
  6. The forces acting on a sliding hoot, the key element of swash - plate axial piston pump. are analyzed and the formulas computing squeezing and repelling forces are derived ; the redundant squeezing force method is presented, including the selection of parts materials, squeezing force factor and the determination of geometric parameters of a sliding hoot

    摘要分析了斜盤式軸向柱塞泵的關鍵摩擦副零件滑靴的受力，導出了壓緊力和分離力的計算公式；介紹了滑靴設計方法中的剩餘壓緊力法，包括零件材料、壓緊力系數的選擇以及滑靴關鍵幾何參數的確定。
  7. The autonomous underwater vehicle which carries liquid oxidizer and liquid incendiary agent and uses the outside seawater as coolant request the oxidizer 、 incendiary agent and coolant can supply the power system according to accurate proportion and reasonable flow on any condition. the system should have small volume and light weight and should be easily realized. the system and control mode introduced in this article can fit these requirements well

    控制或降低液壓系統油液的污染度和提高液壓元件的污染耐受能力是確保液壓系統可靠工作的兩個重要方面，本文分析了液壓柱塞泵所在系統油液污染特性一定時影響泵污染耐受能力的諸多因素，指出了在結構形式確定的條件下設計高污染耐受度液壓柱塞泵所要求的摩擦副材料與主要表面工藝
  8. Application of disk friction pump in axis seal

    圓盤摩擦泵在軸封中的應用
  9. Fluid physical properties, pressure measurement, forces due to static fluids, bernoulli ' s equation, general energy equation, energy losses due to friction, pipe line systems, pump selection and application, open channel flow

    本課程含流體物理性質、壓力測量、沉體平面和曲面所受作用力、柏努利方程式、一般能量方程式、摩擦形成的能量損失、管線系統、明渠流、泵的選擇與應用。
  10. In the third chapter, the mathematical models of project system have been established, and simulation has been done on the simulink enviroment of matlab software kits. the simulation focus on the effects of main parameters on the dynamic characteristics of speed control system, and the main parameters include viscosity damp coefficient and friction torque of electrical motor shaft, internal leakage coefficient of pump / motor of hydraulic circuits, gas volume of pressure accumulator, viscosity damp coefficient of cylinder piston and different running building floors, etc. at last, theoretical research effects of the flow and pressure pulsation of pump / motor on car speed and oil volume leakage theory are discussed. the fourth chapter of this thesis concerns the research on the key items about hydraulic power control system according to the ens 1 - 2 and other hydraulic elevator standards

    論文第三章針對組成系統的各個模塊進行了機理建模，並且通過matlab軟體中的simulink圖形化模擬環境進行了本課題系統的模擬研究，主要針對影響系統特性的主要參數變化，動態分析系統的輸出特性，在上下行工況中，分析了電機軸系粘性阻尼系數、軸系摩擦力矩、主迴路蓄能器迴路液壓泵馬達內泄漏系數、蓄能器氣體容積、液壓缸柱塞粘性阻尼摩擦系數以及不同運行樓層工況等參數對系統特性的影響；最後對軸向柱塞泵馬達的流量壓力脈動對電梯轎廂速度的影響和蓄能器內油液體積損失機理進行了理論研究。
  11. As a new type of power transmission device utilizing the shear of oil of film between two sets of discs. it is widely used for speed regulation and energy saving in large fans and pumps

    液體粘性調速離合器是一種靠摩擦片之間的油膜剪切力來傳遞動力的新型傳動方式，在大功率風機、水泵調速節能方面有著廣泛的應用前景。
  12. This task will be foundation to develop a new type hydrostatic transmission piston pumps with high efficiency, long life, high pressure and high speed, which combined the item of nature science fund of zhejiang province, tribology study on sealing, hydrostatic support and piston on hydrostatic transmission piston pump. in this paper, a new design idea of the ball friction coupling based on hydrostatic bearing was given, and analysis was carried out to the static state properties and the dynamic properties of the oil - film of this friction pair

    本課題是結合浙江省自然科學基金項目「靜壓傳動柱塞泵的密封、靜壓支承和柱塞的摩擦學研究」 （ 501073 ） ，為研發高效率、長壽命、高速、高壓靜壓傳動柱塞泵提供一定的理論基礎，著重研究了滑靴副和球鉸副的動靜態特性，提出了基於靜壓支承的球鉸副設計原理。
  13. In this paper, a new radial piston pump is brought out. the traditional stator - piston is replaced by rotor - piston in this pump. the both properties of static state and the dynamic of the oil - film of this friction pair are analyzed

    本文提出一種新的徑向柱塞泵，該泵採用滾子?柱塞副代替了傳統的柱塞?定子副，並對該泵重要摩擦副的靜態特性和動態特性進行了研究。
  14. The peculiar mechanical character about pumping liquid concrete is discussed. based on the supposition that the ability of transferring hydraulic pressure of liquid concrete is orthotropic and the friction forces exists between concrete and steel tube, the pressure formulas of liquid concrete and the allotting formulas of deadweight are reasoned out. a new method is brought forward for allotting deadweight of liquid concrete during simulation analysis in pumping - core - concrete construction phase, which improves the calculation precision

    在探討泵送液態混凝土的特殊的力學性質基礎上，在假定液態混凝土傳遞壓強能力為正交各向異性、混凝土與鋼管壁之間的存在有摩擦力的前提下，推導出液態混凝土壓強公式和自重荷載的分配公式，提出了在進行鋼管內混凝土灌注過程的施工模擬分析時處理液態混凝土自重荷載分配的合理方法，從而提高施工模擬分析的計算精度。
分享友人
分享到 Line

分享到臉書