撓曲強度 的英文怎麼說
中文拼音 [náoqūqiángdù]
撓曲強度
英文
flexing strength-
Zijingguan fault zone is characterized with cataclasite series of tectonic rocks and joints alongside the deformational zone, and sometimes with uniclinal flexure or folds. the intensity of deformation increases from the sides to the center of the fault in the section, which appears from joints to cataclastic rocks
紫荊關斷裂帶兩主斷裂變形帶以碎裂巖系列構造巖和節理帶組合為特徵，局部出現撓曲和褶皺，由兩盤至斷裂中心變形強度增大，一般由節理帶過渡為碎裂巖帶。In the hogging condition, double bottom and the side shell remain the ultimate bucking strength, deck and upperwing tank remain the yield stress, and the other parts keep elasticity. then the key to calculate the ultimate strength of ship hull girders is to ascertain the ultimate bucking strength of the stiffened panels. in this regard, the developed formulation is designed to be more sophisticated than previous simplified theoretical method for calculating the ultimate strength of stiffened panels under combined in - plane bending and lateral pressure. fabricatio n - related initial imperfections ( initial deflections and residual stresses ) are included in the panel ultimate strength calculation as parameters of influence. all possible collapse modes involed in collapse of stiffened panels, including overall buckling collapse, column or beam - column type collapse, tripping of stiffeners and local bukling of stiffened web are considered
確定了船體梁整體破壞時的剖面應力分佈之後，關鍵在於確定板架的極限屈曲強度。本文充分考慮了在縱向彎曲、橫向壓力作用下加筋板可能發生的幾種破壞模式，即板架的整體屈曲破壞、樑柱形式的破壞、筋的側傾、腹板的屈曲並同時考慮了初始焊接殘余應力、初撓度的影響，使其更精確的計算加筋板的屈曲強度。對于加筋板中加強筋腹板的局部屈曲，採用解析法推導出筋的腹板的撓度方程及其邊界條件，求解相應的方程，從而計算出腹板的局部屈曲應力。Testing methods for flexural strength of adhesive bonds
膠粘劑粘合點抗撓曲強度的試驗方法Partially prestressed concrete structure has been widely used in the field of civil engineering. the deformation is very important for prestressed concrete members, for they are thinner than those of reinforced concret owe to the adoption of hign - intension material and developed technic of design and construction. at present, there are some formulae for deformation in the criterion of many countries. mostly there are 3 methods in use : double linearity method, method of valid inertia and curvature integral calculus method. this article will discuss the influence of material, spa, construction form, and adjust the formula for stiffness of gb50010 - 2002 to a new uniform formula for deformation
在土木工程領域，部分預應力混凝土結構因其良好的跨越能力和經濟性而得到了廣泛的應用，並發揮了巨大的作用。由於採用了高強度材料並進一步改善了設計和施工技術，預應力混凝土構件一般比普通鋼筋混凝土構件更為細巧，因此，撓曲變形問題顯得尤為重要起來。目前，各國規范對于部分預應力混凝土構件的變形計算均有相應的公式，變形計算的關鍵是剛度的計算。Advanced technical ceramics - methods of testing monolithic ceramics - thermo - mechanical properties - determination of flexural strength at elevated temperatures
高級工業陶瓷.整體陶瓷的試驗方法.熱機械特性.高溫下撓曲強度的測定Testing sprayed concrete - flexural strengths first peak, ultimate and residual of fibre reinforced beam specimens
檢測噴射混凝土.纖維鋼筋梁的撓曲強度第一峰最後和殘余Test method for flexural strength of adhesive bonded laminated assemblies
膠粘劑粘結的層壓部件撓曲強度的試驗方法Standard test method for flexural strength of manufactured carbon and graphite articles using four - point loading at room temperature
在室溫下用四點負荷法測定炭加工品及石墨製品撓曲強度的標準試驗方法Testing method for flexural strength modulus of rupture of fine ceramics
精製陶瓷的撓曲強度試驗方法Testing method for flexural strength modulus of rupture of fine ceramics at elevated temperature
高溫下精製陶瓷的撓曲強度試驗方法In the other method, young ' s modulus, residual stress, and bending strength are characterized under a wedge tip by means of micro bridge deflection tests
利用楔形壓頭和薄膜微橋撓曲法，得到了標準氮化硅、低應力氮化硅和氮化鋁薄膜的楊氏模量、殘余應力和彎曲強度。Methods of test for masonry - determination of flexural strength
磚石建築體的試驗方法.撓曲強度的測定Plastics - determination of temperature of deflection under load - high - strength thermosetting laminates
塑料.載荷下撓曲溫度的測定.高強度熱固性疊層板材Plastics - determination of temperature of deflection under load - part 3 : high - strength thermosetting laminates and long - fibre - reinforced plastics
塑料.載荷下撓曲溫度的測定.第3部分:高強度熱固性疊層板和長纖維增強塑料Test method for flexural strength of manufactured carbon and graphite articles using four - point loading at room temperature
在室內溫度條件下利用四點加載進行碳與石墨人造物撓曲強度試驗方法Plastics - determination of temperature of deflection under load - plastics, ebonite and long - fibre - reinforced composites
塑料.載荷下撓曲溫度的測定.塑料硬橡膠和長纖維增強合成物Plastics - determination of temperature of deflection under load - part 3 : high - strength thermosetting laminates and long - fibre - reinforced plastics iso 75 - 3 : 2004 ; german version en iso 75 - 3 : 2004
塑料.載荷下撓曲溫度的測定.第3部分:高強度熱固性疊Methods of test for masonry - part 2 : determination of flexural strength
圬工試驗方法.第2部分:撓曲強度的測定Agglomerated stone - test methods - part 2 : determination of flexural strength bending
燒結石料.試驗方法.第2部分:撓曲強度Methods of test for screed materials - part 2 : determination of flexural and compressive strength
找平層材料試驗方法.第2部分:撓曲強度和抗壓強度測定分享友人