擠壓荷載 的英文怎麼說
中文拼音 [jǐyāhézǎi]
擠壓荷載
英文
racking load-
The characteristics of high pressure gyratory sprayed pumping discusses is presented, which is applicable in wide range of scope and ground layers, convenient for construction, long durability, wide source of materials. mechanism for subgrade strengthening : complex foundation of cement solid and earth between piles was formed by pulsant load of flowing pressure and spraying flow, water wallop, cavitation phenomenon, water wedge effect, extrusion force and air flow agitation etc so as to enhance foundation bearing force and reduce settlement and deformation
高壓旋噴注漿技術具有適用范圍、適用地層較廣，施工方便，耐久性好，材料廣闊等特點；其加固地基機理主要是通過流動壓、噴射流的脈動負荷、水塊的沖擊力、空穴現象、水楔效應、擠壓力、氣流攪動等效應形成水泥固結體與樁間土的復合地基，從而提高地基承載力，減少沉降變形。In different in terne die travel, the metal flow characterize in warm extrusion forming processes and the affection for the flow of metal stage which made by the difference between the blank bottom altitude and the axial direction limiting size in warm extrusion forming technique have been analysed we have gotten the equivalent strain field and the velocity field and other field variable that the blank in different in terne die travel and the die travel - load curve. at the same time, we have analyzed the contributing factor for the oil pump stator forming process optimized and achieve thereasonable die parameter for the war m extrusion forming finally, the optimized technics parameters were used into pilot production, then the qualified oil pump stator forging were produced, the analog results were compared with those of pilot production
論文具體分析研究了不同成形工藝過程中金屬流動的特點，並對不同凸模行程下溫擠成形過程中的金屬流動特點、坯料連皮厚度（底部高度）與溫擠壓成形工藝中的軸向界限尺寸的差值對金屬變形階段的影響進行了分析，獲得了坯料在不同凸模行程下的等效應變場、速度場等場變量及凸模行程-載荷曲線，同時對油泵定子成形過程的影響因素等進行了分析，優化並獲得了合理的溫擠成形工藝及模具參數。最後，利用模擬優化獲得的各項工藝參數進行生產實驗，得到實際生產出的合格油泵定子件，並將模擬結果與生產實驗結果進行比較。The stress distributions under load or unload as well as under fatigue tension with or without split - sleeve were studied, so as to reveal the advantage of coldworking with split - sleeve
研究了帶襯套擠壓件在加載、御載及疲勞拉伸載荷狀態下的應力分佈，並和無襯套擠壓時的狀態進行比較，從機理上揭示了帶襯套擠壓在改善試件抗疲勞性能方面的優勢所在。At last, the load transmission property of cast - in - place piles, the developing cause of friction resistance and base resistance, and some factors which influence pile ' s bearing capacity and settlement are analyzed. then, we introduced two parameters, e and c to represent the disturbing effect in pile construction on parameters of modulus es and cohesive c, which determined by the pressed piles
在這個基礎上進一步分析了打入樁的沉樁擠土效應對樁荷載傳遞的影響及其與靜壓樁的差異，在靜壓樁修正系數k _ c和k _ e保持不變的情況下，再引進打入擾動系數_ e和_ c ，以其和原來靜壓樁的k _ c和k _ e的乘積作為打入樁時的修正系數。The fastened end of bar was machined to multi cone - shaped heads. through the cone heads compress the inorganic anchoring material, the load was transmitted from bars to base material. it changes the transfer path of loads and takes advantage of high compress strength of inorganic material, thus enhanced the anchor intensity of inorganically post - installed bars
本文提出一種新型的植筋技術? ?帶錐頭無機植筋，它把鋼筋錨固端加工成多個錐頭，通過錐頭對無機錨固材料的擠壓，將荷載傳遞給基材，使基材與無機錨固材料的界面上產生剪壓復合應力狀態，改變傳統植筋的受力機理，利用了無機錨固材料抗壓強度高的特點，從而提高了無機植筋的錨固強度。Is the residual stress around a cold expanded hole undercyclically tensile applied stress monotonically attenuating
交變載荷下冷擠孔邊壓殘余應力衰減的非單調性In order to overcome the shortages resulted from hypothesis of small deformation in radial symmetry based on thick - wall cylinder, plane stress and uniform pressure about residual stress around cold - expanded hole, a new model was proposed which takes into consideration the effect of split - sleeve, the different states along thick direction of specimen
摘要針對目前在研究冷擠壓孔邊殘餘應力時，大都採用基於厚壁圓筒的軸對稱小變形、平面應力狀態、孔邊受力為均布載荷等假設所帶來的不足，提出了在三維真實模型狀態下，考慮襯套對孔邊受力的影響、試件在厚度方向上的應力差異等因素。All personnel must keep out from under suspended loads, and should not position themselves between a load and a solid or fixed object where the load could swing or move and create a crushing hazard
《承包商》及其雇員不可在懸吊荷載的下方逗留，也不可站在荷載固定物體或固體物之間，以防荷載可能移動或搖擺，造成擠壓危險。分享友人