收縮缺陷 的英文怎麼說

中文拼音 [shōusuōquēxiàn]
收縮缺陷 英文
shrink defects
  • 收 : Ⅰ動詞1 （把攤開的或分散的事物聚集、合攏） put away; take in 2 （收取） collect 3 （收割） harvest...
  • 縮 : 縮構詞成分。
  • 缺 : Ⅰ動詞1 （缺乏; 短少） be short of; lack 2 （殘缺） be missing; be incomplete 3 （該到而未到） be ...
  • 陷 : Ⅰ名詞1 （陷阱） pitfall; trap2 （缺點） defect; deficiency Ⅱ動詞1 （掉進） get stuck or bogged do...
  • 收縮 : 1 （由大變小; 由長變短） contract; shrink 2 （緊縮） concentrate one s forces; draw back 3 take u...
  • 缺陷 : defect; fault; faultiness; vitium; lesion; flaw; disorder; imperfection; drawback; blemish
  1. But high strength concrete has many defects itself. mainly foy : with higher strength be much fragility ; the final strength increments are smaller for high volume silica - ash concrete ; because high strength concrete ’ s self - shrinkage is large, so the deformation performance is much severely with the strength increments

    而高強混凝土又有其自身缺陷，主要是:強度越高，脆性越大;摻入硅灰量大的高強混凝土，後期增長減小;由於高強混凝土自收縮大，因而變形性能也隨強度等級的提高而變得嚴重。
  2. Characteristic defects are of two main types; regression and syneresis.

    特徵缺陷主要有兩類：即退化和脫水收縮。
  3. The thesis studies the influence of compounding polypropylene fiber and expansion agent to plastic shrinkage of mortar

    摘要混凝土的塑性收縮裂縫，是其結構原生缺陷的主要來源，無論是否可見，都會影響混凝土的耐久性。
  4. Ptfe is one of the most corrosion - resistant materials in the world. however it has defects such as the hot expansion and cold contraction rate is10 times larger than that of steel and the original cold fluidity ( creeping ) etc. therefore, as temperature increases, ptfe extends so excessively that it would collapse and then block the flow of media ; as temperature decreases, ptfe contracts so excessively that it would be ripped and then cause leakage

    Ptfe是當今最耐腐蝕的材料之一，可它被製造成襯里的時候，會存在熱脹冷縮比鋼鐵十多倍及固有的冷流性等缺陷，致使ptfe襯里管道、設備，在使用過程中，溫度高時， ptfe襯里層會伸長過多而內癟，阻塞了介質流通；溫度低時， ptfe層會收縮過大被拉裂而泄漏。
  5. The injection process parameters influencing on injection, debinding behavior and process influencing on defects, sintering influencing on shrinkage, density, mechanical properties, and stainless steel adding cu for injection molding were examined. the experiment showed that flowing property of mixing was improved other than stability with increasing temperature and paraffin ratio in binder

    用石蠟、聚乙烯、聚丙烯為添加劑，油酸為表面活性劑，組成石蠟基多組元粘結劑體系，研究注射成形工藝過程，工藝參數對成型的影響，脫脂行為和脫脂工藝對脫脂缺陷的影響，燒結工藝對收縮率、密度、力學性能的影響，以及含銅不銹鋼對不銹鋼耐蝕性的影響。
  6. This paper studies the theoretical disadvantages of the effective modulus method ( emm ) for calculating the restraining stress of the walls restrained by basement, especially those adopting the shrinkage compensation concrete ( scc ). to avoid these disadvantages, a new time - tracing method ( tim ) is proposed, and base on its analysis results, the effectiveness of the scc for the cracking control of the walls is revisited

    本文研究了在計算基礎墻（尤其是補償收縮混凝土澆築的基礎墻）的約束應力時，等效模量法存在的理論缺陷，提出了更為完善的時程方法，並基於時程方法的計算結果，對補償收縮混凝土在基礎墻中的控裂效能進行了重新評價。
  7. Abstract : the paper puts forward a strengthening plan of defective cast in - place short pile through quality accident analysis. the properties of no shrinkage and high mobility concrete, and its aplication for short pile strength are discussed. result for strengthening is ascertained by measuring. an effective method is given for this case

    文摘:本文就缺陷性鉆孔灌注短樁基礎進行了質量事故分析，提出了加固方案，評述了無收縮高流態混凝土的性能及其在加固中的應用，並對加固的效果進行了檢測，為特定條件下的類似短樁的加固處理提供了實例。
分享友人
分享到 Line

分享到臉書