數字伺服 的英文怎麼說

中文拼音 [shǔzìcìbì]
數字伺服 英文
digital servo
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 字 : Ⅰ名詞1 （文字） character; word 2 （字音） pronunciation 3 （字體） form of a written or printed ...
  • 服 : 服量詞（用於中藥; 劑） dose
  • 數字 : 1. （表示數目的文字; 表示數目的符號） figure; digit; numeral; character; numeric character 2. （數量） quantity; amount
  1. The circuit receives feedback signal of encoder, disposes it by pid and in the form of digit sends control signal which is transformed by d / a into analogue signal to servo amplifier, so further to control motors

    電路板接收碼盤反饋信號，通過內嵌的pid演算法，以數字形式給出控制量，經過d a轉化為模擬控制信號給伺服放大器，進而控制電機運行。
  2. At the aspect of hardware design, it adopts pulse distributor and the technology of single polar voltage drive to accomplish the function of controlling and driving stepmotor ; it adopts the technology of pulse width modulation and cmos h - bridge drive to accomplish the function of controlling and driving dc servomotor ; it adopts d / a convertor to accomplish the function of controlling ac transducer ; it adopts the technology of digital phase detection to accomplish the function of detecting the feedback position signal of induction phase shifter ; it adopts dsp ’ s capture cell to accomplish the function of detecting the feedback position signal of photoelectric coder

    硬體方面，採用脈沖分配器和單極性電壓驅動技術實現了步進電機的控制和驅動功能;採用脈寬調制技術和cmos互補h橋驅動技術實現了直流伺服電機的控制和驅動功能;採用d / a轉換器實現了交流變頻器的控制功能;採用數字化相位檢測技術實現了感應移相器位置反饋信號的檢測功能;採用dsp的捕獲單元實現了光電編碼器位置反饋信號的檢測功能。
  3. The author will research two different realizations : 1 ) to design a can bus interface system based on scm system. this interface system would change the digital commands obtained from the c ' an bus into the analog control signals and send these signals to the existing analog electric servos

    這項工作將研究兩種實現方案： 1 ）設計一個基於單片機系統的canbus介面系統，用來將can總線上的數字指令轉換為模擬控制信號，送給已有的電動伺服模擬控制系統。
  4. The author will research two different realizations : 1 ) to design and realized a can bus interface system based on scm system. this interface system would change the digital commands obtained from the can bus into the analog control signals and send these signals to the existing analog electric servos

    這項工作將研究兩種實現方案： 1 ）設計一個基於dsp的can總線介面系統，用來將can總線上的數字指令轉換為模擬控制信號，送給已有的電動伺服模擬控制系統。
  5. The design of digital ac pmsm controller

    交流永磁同步電機全數字伺服控制器設計
  6. The machine is equipped with 8 sets of numerical ac servo systems and motors as well as floor structure of 3 guide lights controlled by step motor

    本設備採用8套數字交流伺服系統及電機，採用落地式、步進電機控制的三激光燈標結構。
  7. Considering the realization of the system, the paper adopts incremental mathematical pid controller and manufactures the power board, servo amplified board and signal processing board. and the hardware circuit and sensors are checked and debugged

    考慮到系統的可實現性，利用了增量式數字pid控制器，設計了電源板、伺服放大板和信號調理板，對硬體電路和傳感器進行了標檢和調試。
  8. If we tracked satellite by the tradition narrow beam antenna, that should caused the jumping tracking between multi - aircraft. that is difficult to achieve by the immense antenna boot and the follow - up system. using digital beam forming realize aircraft target tracking and controlling should be best means to resolve this problem

    隨著我國多星測控系統的發展，在一個測控站作用范圍內將出現多星，同時要求地面站對多星同時進行跟蹤測控；如果採用傳統的窄波束天線對目標進行跟蹤測控，必然導致天線在多個飛行器之間進行跳動跟蹤，這對于龐大的天線引導、伺服系統來說難以實現，採用數字波束對飛行器目標進行跟蹤測控是解決此問題的最好方法。
  9. Digital simulation for the forging process of bearing ring

    基於全數字伺服控制單元的運動控制演算法的研究
  10. In the first part, a style of digital servo - system is developed, which will be applied to the electronic interference device

    第一篇介紹用於某型通用電子干擾設備的數字伺服系統的研究。
  11. This platform is used for testing the performance of su - 27 aircraft and 31e - mk optoelectronic collimation integrated system. it uses all - digital servo control system to enhance the performance of the simulation platform in order to get higher precision and better stability

    其用於在內場檢測蘇二七飛機31e - mk光電瞄準綜合系統的工作性能，在本模擬狀態中採用全數字伺服控制系統，使模擬轉臺控制精度更高，穩定性更好。
  12. The full - digital servo control system of satellite antenna has already passed the whole satellite payload system test. the result shows that the system has good speed stability, high precision scan period and can work reliably under the simulative space environment

    本文所設計的衛星天線全數字伺服系統已通過衛星有效載荷系統的聯試實驗，結果表明：該系統具有較高的轉速穩定性和高精度的掃描周期，可以在外太空模擬環境下長期可靠地運行。
  13. Data communication protocol based on dual can bus for digital servo drive

    總線的數字伺服通信協議
  14. We have established an exact mathematics model, and analyzed the adjustable parameters of pneumatic servo system theoretically, at the same time, we have putted forward a special programmable structure and method, and provided theoretic gist for the development of pneumatic digital servo robot

    建立了較準確的氣動數字伺服缸的數學模型，並對氣動伺服系統的調節參數進行了理論分析，提出了一種可以節省可編程式控制制器空間的特殊程序結構和編程方法，為氣動數字伺服機器人的發展提供了理論依據。
  15. In this paper, a dual - axis digital ac servo - system is studied. the overall design of this system was introduced

    文中介紹了該交流數字伺服系統的總體設計方案。
  16. Its main traits are as follow : the system is an intellectualized digital servo system based on microcomputer measurement & control technology

    該系統的主要特點是：它是一個智能化的數字伺服系統，又是一個典型的基於微機測控技術的伺服控制系統。
  17. Abstract : the operation principle and control method of electro - hydraulicdigital servo valve are first introduced

    文摘:介紹了一種直動式電液數字伺服閥的結構原理及其控制方法。
  18. Pneumatic digital servo technology is the developing production of pneumatic and digital technology ; it delegates the highest level of pneumatic technology

    氣動數字伺服技術是氣動技術與數字技術共同發展的產物，代表著當今氣動技術發展的最高水平。
  19. In addition, as the digital missile develops fast the mil - std - 1553b bus becomes more and more popular in missile system, so designing the digital controller with communication function for servo systems has great meanings

    另外，隨著數字化導彈的迅速發展， mil - std - 1553b總線在導彈系統中的應用的越來越多，設計具有1553b通訊功能的數字伺服控制器對于提高導彈性能具有重要意義。
  20. At last, this paper puts forward that the further study is to install video equipment on pc so as to monitor the real image and realize network manufacture and remote trouble diagnosis as well as to develop the cnc system employing digital servo - dc and servo - ac motors, which help to form a series of commercial products

    最後，本文指出了進一步研究的方向是通過攝像設備在pc端進行真實圖像監控，實現網路化製造和遠程故障診斷以及開發使用數字伺服直流和交流電機的數控系統，形成商品化的系列產品。
分享友人
分享到 Line

分享到臉書