數據補償程序 的英文怎麼說

中文拼音 [shǔjùbǔchángchéngxù]
數據補償程序 英文
data compensation routine
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 據 : 據Ⅰ動詞1 （占據） occupy; seize 2 （憑借; 依靠） rely on; depend on Ⅱ介詞（按照; 依據） according...
  • 補 : Ⅰ動詞1 （修理; 修補） repair; mend; patch 2 （補充; 補足;填補） fill up; add supplement; supply; ...
  • 償 : 動詞1. （歸還; 抵補） repay; compensate for 2. （滿足） meet; fulfil
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 數據 : data; record; information
  • 補償 : compensate; make up; make up for; make it up to sb. ; make sth. good; compensation; offset
  • 程序 : 1 （進行次序） order; procedure; course; sequence; schedule; ground rule; routing process 2 [自動...
  1. ( 2 ) by using the methods of analytic geometry and mbs and parameter measure map along x - axes by 9 - line distinguish method, the formulas for correctly identifying the error parameters have been established

    （ 2 ）針對sk - 21數控磨床開展誤差參數檢測實驗，通過現場測量，獲得凸輪工作臺直線運動誤差和旋轉誤差數據，運用9線辨識法進行分析，經數學處理后為補償程序提供必要數據。
  2. A routine or storage used to compensate for a difference in rate of flow of data, or time of occurrence of events, when transferring data from one device to another

    當數據從一個設備傳送到另一個設備時，用於補償數據流速率差或事件發生時間差的一種例行程序或存儲器。
  3. The software design uses c51 high - level language to write the modularization programme. by dint of matlab, the precision of system improve by software compensation. in order to avoid the blindness of temperature coefficient, meanwhile, an auto - temperature compensation way via single - chip is brought out

    軟體部分使用c51高級語言編寫模塊化程序，並藉助matlab的數據擬合功能，實現對誤差的軟體補償，提高了測量精度;同時提出了一種運用單片機實現測量系統自動溫度補償的在線查表法，避免了傳統的選擇溫度補償系數存在的盲目性。
  4. Firstly, the text introduces the general circs of guided weapon and the principle of gfimu theory, then discusses the way, as well as the reason, to design the hardware of the system, which is composed of accelerometer configuration, compensating circuit, signal regulating circuit planning, and signal processing unit designing ; thereon is about software design philosophy, including data acquisition, compensation algorithm, digital filter, gfimu algorithm and data transmission method ; during the design procedure, accuracy and speed are fully been considered ; finally, through experiment and analysis we reveal the problems exist in the system and bring forward the corresponding improvements

    論文首先講述了制導武器的發展概況、無陀螺慣性測量的發展和原理，然後詳細介紹了系統各部分硬體的設計思想和設計方法，包括傳感器配置結構、傳感器補償電路、信號調理電路以及信號採集處理單元;文章接下來介紹了系統軟體設計:主要分為數據採集、補償演算法、濾波演算法、無陀螺慣性測量演算法和數據傳輸幾個部分。系統設計過程中著重考慮了測量精度和程序執行速度的問題;論文的最後是系統實驗和數據分析，並根據實驗中發現的問題對現有系統作了進一步的改進。
分享友人
分享到 Line

分享到臉書