斜孔道 的英文怎麼說
中文拼音 [xiékǒngdào]
斜孔道
英文
flume-
The thermal visualizations of jet impingement cooling with single or double row holes inside semi - enclosed channel are measured by using infrared camera and then the impingement cooling heat transfer coefficients are deduced. the effects of flow and geometry parameters on convective heat coefficients are obtained. the results show that : for a single row normal impingement, the impingement cooling effectiveness is enhanced with the increase of impinging reynolds number or the decrease of hole space to diameter ratio, and the best effectiveness is achieved under the jet - to - surface spacing equals to 2 ; when the jet is oblique to the confined wall, the cooling effectiveness is weaken especially under the jet - to - surface spacing ratio is greater than 2 ; for double rows normal impingement cooling, the cooling effectiveness of rear row jet is weaker than the front row under lower impinging reynolds number or bigger jet - to - surface spacing
對于單排垂直射流，沖擊冷卻效果隨射流雷諾數的增加、孔間距與直徑比的減小而得到提高，沖擊間距比為2時換熱效果最好;沖擊孔中心線向通道封閉一側傾斜后，射流沖擊冷卻的范圍變窄，當沖擊間距比大於2時駐點區的對流換熱能力明顯降低;對于雙排沖擊射流，孔排間距與直徑比的增加使沖擊冷卻范圍變大，但在兩排孔之間區域的對流換熱系數有所下降;在較小的沖擊射流雷諾數和較大的沖擊間距比下，後排射流的沖擊換熱效果要遜於前排射流。Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating
箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。This method offers more precise geometry for spaceborne sar system design and simulation. 3. in the analyzing on the radar doppler properties, under the ellipsoid earth model and ellipse orbit model, considering the earth rotation, the radar doppler properties with different orbit eccentricity are compared, and the fact that orbit eccentricity affects doppler frequency rate is found
在雷達多普勒特性分析中，論文採用橢球地球模型和橢圓軌道模型，結合地球的自轉，通過不同偏心率下雷達多普勒特性的比較，研究了軌道偏心率對合成孔徑雷達系統設計與模擬軟體研究雷達多普勒調頻斜率的影響。A flap vlave used in pumping station is a kind of hydraulic - operated automatic gate, which is similar to a hinged check vaive. because of their simple structure and reliability, being able to shorten the length of outlet passage and facilitate the starting of pumping system in comparison with siphonic vacuum - distroied cutoff scheme. so it is propitious to be used and save investment but at the same time, flap valves always show some disadvantage
因拍門簡單、可靠，與虹吸真空破壞截流閉鎖方式相比，可以縮短出水管道（流道）長度，並利於泵系統起動，與快速閘門相比，拍門也有諸多優點，閘門門體易關閉不到位或卡住不能活動，因為門槽和?塊較軸孔容易殘留異物，閘門門體克服滑動阻力不僅無機械增益，且阻力和動力不在一直線上，門體易傾斜而自鎖，而拍門的工作可靠性則遠高於快速閘門。With two structures of bore cylindrical or tapered and retainers made of steel sheet or synthetic resins, the bearings are characteristic of their spherically formed outer ring raceways allowing for misalignment within 3 degree deflection between inner ring and outer ring, so as to compensate concentricity and deflection errors
詳細信息:調心球軸承由圓柱孔和圓錐孔兩種結構，保持架的材質有鋼板、合成樹脂等，其特點是外圈滾道成球面形，具有自動調心性，可以補償不同心度和軸撓度造成的誤差，但其內、外圈相對傾斜度不得超過3度。分享友人