時限裝置 的英文怎麼說

中文拼音 [shíxiànzhuāngzhì]
時限裝置 英文
time adjusting device
  • 時 : shí］Ⅰ名1 （比較長的一段時間）time; times; days:當時at that time; in those days; 古時 ancient tim...
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 裝 : Ⅰ名詞1 （服裝） dress; outfit; attire; clothing 2 （演員的化裝品） stage makeup and costume Ⅱ動詞...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 時限 : time limit
  • 裝置 : 1 （機器設備的配件）installation; device; apparatus; equipment; arrangement; gear; appliance; rig...
  1. This paper simply introduces the device of on - line monitoring for the thrust of the rotating maching, then discu ed the finite dement analyses on the on - line monitoring elastic dement for measuring thrust in detail, in order to develop the performance of the se or and the device, we calculated the distribution of the stre 、 strain 、 axial di lacement in the elastic element using the finite element method when the axial forces f = 3 104n, the result is very satisfied

    簡單介紹大型旋轉機組軸向力在線監控裝置，然後詳細介紹軸向力測力彈性元件的有限元分析，為了提高所研製的測力傳感器的性能，採用有限元方法計算了彈性元件在軸向力f = 3 104n時的應變、應力、靈敏度及軸位移等的分佈情況，分析結果表明：所設計的測力傳感器完全符合廠方的要求及儀表性能指標。
  2. Roll over protective structure ( rops ) is a device which installs on out of construction vehicle. the main functions are : when the vehicle rolling over. rops can prevent the vehicle from rolling over further, and reduce the possibility of rolling vehicle injures operator ; when the vehicle traveling on freezing soil. concrete and rock, it has large resist continuous impact ability ; when the vehicle overturning rops can support the whole vehicle. arrangement of falling object protective structure ( fops ) can block objects ( such as trees, rocks ) so that supply protection for operator. this problem is that research rolling over and falling objects protective structure of bulldozer by learning research condition of rops / fops and relative lay down international standard. on the base of theory analysis. detrudes counting formula of rops / fops deformation through founding mechanics analysis model of rops / fops at the stage of elasticity and plastoelastic. and finds a set of feasible nonlinear finite element analysis counting. lt calculates rops / fops plastoelastic deforma variable of 320hp bulldozer, bulldozer has been carried out by optimizing design method

    其主要功能是：當車輛滾翻時， rops能刺入未凍土壤而阻止車輛的進一步滾翻，降低滾翻的車輛對系著安全帶司機軋傷的可能性；保證rops在碰撞和沖擊變形不大的地面（如凍土、混疑土上、巖石）時，能具有相當大的抗連續沖擊能力；當車輛已經處于顛覆狀態時，已經變形的rops應能支撐住整車。落物保護裝置（簡稱fops ） ，其構件的布置方式要能遮蔽墜落的物體（如，樹木、巖石等） ，以便對司機提供適當的保護。本課題主要通過了解國內外有關對rops fops的研究情況和有關國際標準的制定，對大型推土機傾翻和落物保護裝置進行研究，在理論分析的基礎上，通過建立rops fops的力學分析模型，推導彈性、彈塑性階段rops fops變形的計算公式，建立一套可行的rops fops的非線性有限元分析計算方法。
  3. The research studies affect of the hydraulic characteristic of storage equipment to water quality and put forward hygienical limit hrt to storage equipment by mathematics model

    研究蓄水裝置水力特性對水質的影響，應用數學模型對蓄水裝置提出了衛生學極限流動時間和停留時間。
  4. A movable temporary stay arrangement must be used to limit the cantilever stresses during construction to a reasonable level.

    必須採用一個可移動的臨時拉索裝置將施工過程中的懸臂應力限制在合理的范圍之內。
  5. The research aims at the demonstration and the mend of the design on the new purifier and presents a calculation method for solving the two - phase flow in fluid machine by the finite element method. after analyzing the two - phase flow in the new purifier by means of the continuum model, poisson equation, navier - stokes equation and continuous equation are derived and solved by using the finite element method. the solution on pressure, velocity and particle concentration simulates the departure well between oil and water, which proves the accuracy of the design on the new purifier

    本文採用兩相流連續介質模型，由兩相分離流動理論得到控制方程，採用chorin的直接速度-壓力mac法的思路，對新型油水分離裝置內油水兩相流動作了細致的分析，同時首次把科氏慣性力引入兩相流模型中，進行分析和計算，將研究擴展到三維，並用有限元法分別解poisson方程、 n - s方程、連續方程的方法，對流場內壓力場、速度場、濃度場進行了分析和計算，較好地模擬了新型油水分離裝置內油水分離的現象，證明了設計方案的正確性。
  6. The equipment is made up of oil pump set ( driven by gasoline engine 、 electric motor or manpower ) 、 3 - stage telescopic jack 、 horizontal displacement set 、 rescue riggings etc. according to the railway accident, the equipment can rerailing the derailed wagon 、 overturn them out of demarcation or horizontal displace them out of demarcation. the equipment has the characteristics of rapid rate 、 easy operation and high reliability etc. the equipment is suit for railway rescue team to deal with complex derailing accidents and it ' s an efficient implement for improve rescue ability of railway rescue team

    該機具由泵站（手動或機動） 、三級千斤頂頂升裝置、橫移裝置、臺車索具等組成，根據現場事故情況，可選擇將事故車起復復軌、整體翻出限界、整體移出限界，具有省時速度快、操作簡便、安全可靠等特點，適合救援隊處理較復雜的車輛脫線事故，是提高救援隊能力的一種有效工具。
  7. Since the departing process of fire work departing installation is a highly nonlinear transient dynamic process, it relates to many speciality field, and the characteristic of the material is very complex under the highly rate and highly pressure distortion, the design methods and the design formulae by experience which has been used for a long time are very limited, the facter which truly affect the departing process of fire work departing installation cannot been reflected in the design calculation, the structure modelling and optimization of the fire work departing installation is cannot been carried out by the traditional optimization method

    由於火工分離裝置的分離解鎖過程是一個高度非線性的瞬態動力過程，涉及多個學科和專業領域，而且材料在高速高壓條件下瞬時性態十分復雜，長期以來所沿用的經驗設計方法和設計經驗公式的局限性很大，對火工分離裝置分離解鎖過程一些實際有影響的因素不能定量地反映到設計計算中來，採用傳統優化方法無法實現火工分離裝置的結構優化建模和計算。
  8. Inductotherm group china - thermatool shanghai is a sister company of thermatool group, has more than 50 years experience in designing and manufacturing hf welders, seam annealers, tube / pipe inline bring / dull annealers ( stainless steel, carbon steel, etc. ), tube / pipe form mill and relevant spare parts. as the leading supplier of welders and seam annealers in the world, thermatool has provided wide range of welders and seam annealers to pipe and tube industries

    應達工業（上海）有限公司色瑪圖爾分公司和美國色瑪圖爾公司是姊妹公司，同屬美國應達工業集團，具有50多年專業生產製造高、中頻焊機，焊縫退火設備，管材（碳鋼、不銹鋼）在線光亮/暗退火裝置，焊管成型機組及其附件的豐富經驗，為世界上眾多的行業提供了相應的專業化設備，同時也是世界上最大的高頻焊機和焊縫熱處理設備的製造商。
  9. Negative sequence inverse time overcurrent protection

    負序反時限過流保護裝置
  10. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  11. Abstract : during the heating of scrap with carbon or hydrocarbon contented substances in some process, it will bring problems like explosion of carbon monoxide, fume and smell from oil volatilization, etc. ， if incomplete combustion occurs. through laboratory experiments, the time related variation of gas contents and post combustion ratio of fume during the heating of oil - bearing scrap are studied. the results show that the restrictive chain of reaction procedure is the thermolysis of oil ; that temperature and ( co ) / ( co2 ) ratio influence transformation ratio and post - combustion ratio under lower temperature ; that 900 is the temperature above which the complete reaction can be ensured at all ( co ) / ( co2 ) ratios

    文摘:在某些廢鋼熔煉過程中，當爐料中含碳及碳氫物質且燃燒不充分時，會帶來煙氣中一氧化碳的燃爆、油污揮發時造成的煙霧、臭味等問題.通過實驗室裝置研究含油廢鋼在加熱過程中煙氣成分隨時間的改變以及二次燃燒率的變化，試驗結果表明，反應過程的限制性環節是油分的熱分解；在較低的溫度下（ co ） / （ co2 ）比例影響轉化率和二次燃燒率；而在任意比例下保證充分反應的溫度為900以上
  12. The use of wireless devices and their accessories may be prohibited or restricted in certain areas. always obey the laws and regulations on the use of these products

    無線裝置及其配備可能于指定地區受到限制，請于使用該產品時遵守有關條例及守則。
  13. Please use form no. s16 - 3 if the proposed use is temporary for not exceeding 5 years ; and form no. s16 - 5 for public private utility installation exceeding 5 years or for minor relaxation of stated development restriction for column 1 use or use development always permitted under the covering notes

    若擬議用途屬臨時性質，並為期不超過五年，請使用表格第s16 - 3號若屬為期超過五年的公用事業私人設施裝置，或是略為放寬第一欄用途或注釋說明頁經常準許的用途發展的指定發展限制，請使用表格第s16 - 5號。
  14. The rubber roller controlling by peneumatied device. these limit can beadjusted, guaramteeprecision, shorten time

    壓印膠輥擺臂式上下有可調限位裝置，對版時間短，對版精度高。
  15. Vice chairman jennifer a. hillman and commissioner marcia e. miller announced that they will propose a quantitative restriction for a three - year period on imports of the subject pedestal actuators from china

    10月29日建議布希總統對美國從中國進口的電動機械裝置基座致動器施加臨時數額限制。
  16. This article describes a way of special ultrasonic system which monitors thermal stress in seamless welded rails. this monitoring system is a non destructive testing system, which adopts avr mcu and high - precise time chip processing as the core of it, and adopts the critically refracted longitudinal wave as the object of measuring. my studying focuses on the theory of the monitoring system, which will be listed in this arctile : according to the snell theory, the theory of motivating of critically refracted longitudinal wave is described in details, and the finite element software is used to emulate the propagating course. the formulas of calculating the pts of swr are taken from the acoustoelasticity theory, and the calculating the parameters is introduced. according to assemble materials, three kinds of ways of monitoring the pts of swr using critically refracted longitudinal wave are described, which are measuring the sound - time in changeless distance, ultrasonic critical - angle refractomery and frequency spectrum, the first way of ways is used in this experiment system. the factors, which effect the monitoring system, are assaid in some degree based

    本文的研究工作重點在無縫焊接鋼軌溫度應力測量系統的理論模塊，包括根據snell原理，研究極限折射縱波的激發機理，並使用有限元軟體ansys進行模擬;根據聲彈性理論以及公式推導出計算無縫焊接鋼軌中的溫度應力的公式，並對其中參數的求解方法進行介紹;根據收集的資料，介紹了三種使用極限折射縱波測量無縫焊接鋼軌溫度應力的方法，即固定距離測量聲時法、臨界角折射法和頻譜分析法，本實驗系統使用的是第一種;根據實驗經驗以及相關資料，分析了影響極限折射縱波測量溫度應力的幾個因素，並提出了相應的解決方法;根據實驗系統的需要，獨立設計並加工出相關配套的實驗設備，包括實驗鋼塊、有機玻璃楔塊、固定件、載荷外框裝置等。
  17. The commission made an affirmative determination, finding that certain ductile iron waterworks fittings from china are being imported into the united states in such increased quantities or under such conditions as to cause market disruption to the domestic producers of like or directly competitive products

    裁定，從中國進口的球墨鑄鐵水管配件裝置數量激增，對美國廠商造成了損害或構成了威脅。這一裁決可能導致對這類管件施加臨時關稅或配額限制。
  18. After stiff competition from the competing finalists, shau kei wan government secondary school took first place. the winning team had to complete two tasks in 25 minutes. the students first had to place a carton into another carton that was held under the water, and then use a robotic arm to release the key to an underwater buoy, making it a float to the surface

    各參賽隊伍須于限時25分鐘內將機器人由岸上遙控至水底，並完成兩項任務測試： 1將放在泳池邊的膠箱搬往水底，並將之放進水底的另一個膠箱內2利用機器人手臂拉開預先放在水底之裝置上的鑰匙，使其浮件浮到水面。
  19. The timing - and - quantitation precision injection of lpg was realized with high - speed lpg solenoid valve and a set of electronic control system, which was designed by the author and can flexibly control the gas supply system of lpg. based on the analysis of experimental data got by comparing the performances before and after the application of the set of equipment on lr6105q12 diesel engine, the effects of load, speed and replace ratio, etc on the emissions of smoke, hc and co of dual fuel engine were expounded. through optimization, the smoke emission was utmostly reduced and the emissions of hc and co were within the government restriction

    為此，本文通過對各個方案進行詳細比較，選擇了電控多點順序噴射的供氣方案；利用高速lpg噴射閥和自己獨立開發出一套電子控制系統對lpg供氣進行靈活地控制，實現了lpg的定時定量噴射，並把這套裝置應用到中國一拖生產的lr6105q12柴油機上，在對改裝前後的發動機進行大量試驗和分析的基礎上，闡明了負荷、轉速、摻燒比等因素對雙燃料發動機的煙度、 hc 、 co等排放的影響情況，並且通過優化，最大限度地降低了發動機的煙度排放，同時使hc 、 co排放限制在國家標準規定的范圍之內。
  20. Using the simulation method coupling of multi - body and finite element, the simulation model of frontal impact, side impact and car - pedestrian impact of a certain type of vehicle is established by madymo software, and the comparative analysis of impacting performance of the vehicle fitting with or without this equipment is made out. the simulation results show that the vehicle fitting with this equipment has better damping and energy absorption performance. combines with frontal bumper air bag, not only the injury to the occupants and pedestrians in crash accident can be decreased further, but also the damage to the vehicle can be decreased

    3 .採用多剛體與有限元耦合的模擬計算方法，利用madymo軟體建立了汽車正碰、側碰及與行人碰撞的模擬模型，對有無該裝置時車輛的碰撞性能進行了比較與分析，結果表明安裝有該裝置時車輛具有更好的緩沖與吸能特性;結合前保險杠安全氣囊技術，不僅可以進一步減少碰撞事故對乘員及行人的傷害，而且可以減少碰撞事故對車輛本身的損壞。
分享友人
分享到 Line

分享到臉書