曲線再現機 的英文怎麼說

中文拼音 [qūxiànzàixiànjī]
曲線再現機 英文
curve regenerator
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 再 : 副詞1 （又一次） another time; again; once more 2 （表示更加） still; further 3 （表示如果繼續怎...
  • 現 : Ⅰ名詞1 （現在; 此刻） present; now; current; existing 2 （現款） cash; ready money Ⅱ副詞（臨時; ...
  • 機 : machineengine
  • 曲線 : [數學] curve; bight; bought; profile; net曲線板 french curve; irregular curve; curve board; splin...
  1. It makes decision on stability state of countryrock according to in - situ surveying datum, and grey prediction model is formed using the deformation curve of country rock. this model can predict latter displacement of country rock. deeper analysis is also been counducted on countermeasure and mechanism of softrock tunnel, and gradation analysis method is applied to select the optimum bracing plan

    再結合現場實測資料對地下洞室圍巖的穩定狀態進行判別，利用圍巖變形曲線建立灰色預測模型，採用該模型對圍巖位移的後期變形進行預測。對軟巖隧道的支護對策、支護作用機理進行了較深入的分析研究，並利用層次分析法選擇最優的支護方案。
  2. The main results show that : ( 1 ) the mechanism of laser bending is very different from that in bending with hard tools. ( 2 ) the bending angle is varied along scanning direction, and there is a deformation wave in the process. ( 3 ) the effects of sheet length on bending can be neglected while the length is more than 10 times of thickness. ( 4 ) the sheet width has much higher influence on the bending process

    分析發現：激光彎曲成形時板料的應力狀態與機械折彎時有根本不同；當激光束沿直線單向掃描時，板料兩端的彎曲角度不同；板料的長度大於10倍板厚或5倍光斑尺寸時，板長對彎曲角度的影響不再顯著；沿掃描方向，距離光斑中心3倍光斑尺寸以外的區域，仍然對彎曲變形量產生影響。
  3. In the paper, based on the method of low pair replacing with high pair, the problem of cam design was transferred to that of linkage design. by means of rotary unit vectors, the equations of displacement, velocity and acceleration of the replacement mechanisms were developed. and then, the virtual linkage ' s length and direction were deduced

    論文基於高副低代原理，將平面凸輪機構設計與再現函數的平面連桿機構設計統一為同一種方法，運用圓向量函數建立代換機構的位移、速度、加速度矢量方程式，求取虛擬連桿桿長和方向，由此展開凸輪理論廓線、實際廓線、曲率半徑和壓力角的求解，並得出用圓形刀具加工凸輪時刀具中心的軌跡方程。
  4. Due to the existing volatility, stochastic and dynamic properties of cash flow, this paper employs exponential smoothing method and moving average method to eliminate the effects of the stochastic factors, use the seasonal exponent to eliminate the seasonal volatility of the cash flow, the exponent curve and polynomial fitting curve to estimate the overall cash flow and also provides the calculating methods and identifying principle of the overall cash flow

    由於現金流量的波動性、隨機性、動態性等特性的存在，依靠單一方法無法科學、準確的預測現金流量。論文提出利用指數平滑和移動平滑的方法來剔除隨機因素影響，利用季節指數來消除現金流量的季節波動，之後再利用指數曲線或者多項式擬合曲線來預測整體現金流量的方法，並給出了整體現金流量的計算方法和確定原理。
  5. The paper is based on the project of " the research of mathematics and computer frequency dynamic simulation theory on knobs not result ". the research content is object to the image of log knobs by vidicon getting to detect the shape of log knobs according to the method of video disposal. the paper apply digital image processing technology to log knobs image to swell and detect borders, then distill the surface shape and characteristic parameter of knobs. the thesis depict the knobs three - dimensional models, build the mathematics models of log knobs and simulation two - dimensional image curve of the log knobs primary section which has been discerned, thereby achieve our researching aim to reappear the knobs image on computer

    本論文是國家自然科學基金資助項目「節子ndt結果的數學描述與視頻動態模擬理論的研究」的基礎研究之一，論文的研究內容是通過視頻處理的方法檢測原木表面節子的形狀，以攝像機採集的原木表面節子圖像為對象，運用數字圖像處理技術對節子圖像進行修正、增強、邊緣檢測等處理，提取節子的形狀特徵參數，並運用數學的方法，歸納總結其規律，應用數學的方法對節子的二維模型進行描述，建立原木節子的數學模型，對識別出的原木節子主截面的三維圖像曲線進行擬合處理，從而在計算機上實現節子的分佈與形態的再現，達到研究節子的空間形態和分佈規律的目的。
分享友人
分享到 Line

分享到臉書