最大外移位置 的英文怎麼說
中文拼音 [zuìdàwàiyíwèizhì]
最大外移位置
英文
maximum outward position- 最 : 副詞（表示某種屬性超過所有同類的人或事物） most; best; worst; first; very; least; above all; -est
- 外 : Ⅰ名詞1 （外面） outside; external side 2 （外國） foreign country 3 （以外） besides; beyond; in ...
- 移 : Ⅰ動詞1. （移動） move; remove; shift 2. （改變; 變動） change; alter Ⅱ名詞（姓氏） a surname
- 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
- 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
-
Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc
本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。In this paper, the three level fortification criterion, two stage design method and the elastic response spectrum theory are adopted, and the program of nba ( the program of nonlinear - aseismic analysis for beam bridge ) is used to calculate. through gathering, analyzing and calculating a lot of bridge design materials, this paper induces a simple way to calculate the relative displacement of the beam and the pier, and then according to the current design method, it concludes a better design principle of the supporting length of the beams. at the same time the dynamics is adopted to put forward the design method of the carrying capacity and the lengthen of prestress wire ( steel bar ) falling - off prevention structures of highway bridges
本論文採用三水準設防、兩階段設計方法、彈性反應譜計算理論，運用橋梁結構非線性地震響應分析程序nba （ theprogramofnonlinear ? aseismicanalysisforbeambridge ）進行計算；通過收集大量的實橋設計資料，經分析計算，歸納總結出計算上下部結構相對位移的簡便計算方法；並綜合國內外的經驗值，提出梁的支承長度se的設計原則；同時運用動力學突加荷載的原理，推導分析了預應力鋼絞線式（鋼棒連接式）落梁防止裝置設計承載力的計算方法和設計伸長量s _ f的取值；最後本文通過實橋計算，說明了落梁防止系統設計的方法。This positional inaccuracy may be lowered by introducing additional information in the update message : for example a timestamp stating from which point the speed change was done will make the replicated path finally rejoin the original one, although the temporary phase during when the update message is transitting will have a different path
這種位置上的偏差可以通過在更新包中引入額外信息來降低：比如一個表示速度從什麼時候開始改變的時間戳可以使得復制體的移動路徑最終與實際路徑合併上，雖然在更新包傳輸的過程中，復制體還是會產生一個不大一樣的路徑。
分享友人