最終冷卻 的英文怎麼說

中文拼音 [zuìzhōnglěngquè]
最終冷卻 英文
final cooling
  • 最 : 副詞（表示某種屬性超過所有同類的人或事物） most; best; worst; first; very; least; above all; -est
  • 終 : Ⅰ名詞1 （最後; 末了） end; ending; finish 2 （指人死） death; end 3 （姓氏） a surname Ⅱ形容詞（...
  • 冷 : Ⅰ形容詞1 （溫度低; 感覺溫度低） cold:冷水 coldwater; 你冷不冷? do you feel cold?; are you feeling...
  • 卻 : Ⅰ動詞1 （後退） step back 2 （使退卻） drive back; repulse 3 （推辭; 拒絕） decline; refuse; reje...
  • 最終 : final; ultimate最終裁定 absolute decree; 最終裁決 final ruling; 最終產品 [工業] final products; e...
  1. Electromotor joins with high efficiency selected water pump, scm ( single chip micyoco ) control system commands water pump according to cooling water temperature which substitutes traditional strap - driving mechanism pump and forms tael - level intellectualized control cooling system combining with electromotion control of cooling fan. consequently it realizes that water pump and fan autoregulate with engine working status and assures t hat cooling water temperature keeps in the best range all the time and advances the reliability of engine working and realizes exact control of cooling water temperature in deed

    選用高效率水泵與電機聯接，改由單片機控制系統根據冷卻水溫控制水泵的工作，代替傳統的皮帶帶動的機械水泵，結合冷卻風扇的電動控制形成兩級智能化控制的冷卻系統，從而，實現了水泵和風扇轉速隨發動機工況變化的自動調節，真正實現了冷卻水溫的精確控制，保證了冷卻水溫始終保持在最佳范圍內，大量減少傳熱損失降低油耗，並提高了發動機工作的可靠性。
  2. It was a recurring human fever fated to cool and pass.

    它是一種不斷復發的人類的熱病。最終註定要冷卻，消退。
  3. Results show that the brittle fracture is mainly caused by hydrogen brittleness that results from the oxidation arid absorbing hydrogen of copper tube during braze welding

    同時在加熱和冷卻時，由於異種材料的熱脹系數差別過大，產生的較大熱應力作用於已存在的裂紋，促使裂紋二次擴展，甚至使得晶粒脫落產生空洞，最終導致焊接接頭漏氣失效。
  4. End firing cooling relaxation temperature 3

    最終焙燒冷卻松開壓力溫度3
  5. End firing cooling relaxation temperature 2

    最終焙燒冷卻松開壓力溫度2
  6. Mr albert cheng wai - shing, a chartered engineer from black veatch hong kong limited : " the continued adoption of seawater cooling is a logical technical solution for the end users as there will be minimum interruption to the formal operation of existing pumping stations during the reprovisioning works.

    -博威工程顧問有限公司特許工程師鄭偉成先生： "在技術上，繼續採用海水冷卻系統對最終用戶來說是合理的解決方法，因為在重置工程期間，對現有抽水站的運作所造成的干擾可減至最少。
  7. Because of the effect of sip porous skeleton, the primary si and the eutectic si were separated on the surface of sip porous skeleton under slow cooling conditions, and there were no typical eutectic microstructures in the al - alloys phase of the composites. 6

    處于si相顆粒間隙的過共晶al - si合金液在緩慢冷卻凝固時，初晶si和共晶si會附著在si多孔體骨架上析出，在最終的復合材料中沒有典型的al - si共晶組織。
  8. The water - cooled " alien spacesuits " are being handed out to turret gunners in their notoriously vulnerable humvee vehicles. the protective suit, based on those worn by bomb disposal officers, was intended to cut spiralling casualties for one of the most dangerous jobs in modern warfare

    據每日電訊報5月9日報道，這款具有水冷卻功能的「外太空服」裝甲衣主要為易受攻擊的裝甲車炮兵提供保護，防止他們遭到路邊炸彈的襲擊，最終降低炮兵的高死亡率。
  9. Simulation and rolling test results showed that the effect of laminar cooling patterns on the plate products is small in final phase composition but great in ferrite grain size

    模擬結果和軋制實驗表明，對于低碳中厚板，層流冷卻方式對最終相組成的影響較小，而對產品的鐵素體晶粒尺寸有較大的影響。
  10. The mass flow rate coefficients increase and achieve a constant at last with increasing blowing ratio. the influence of blowing ratio on the heat transfer coefficients and film effectiveness is complex

    流量系數隨吹風比的增大而增大並最終趨于某個定值，但吹風比對氣膜孔下游換熱系數和冷卻效率則較為復雜。
  11. Note : moisture vapor transmission will also increase with permeability and higher wind speeds and promote cooling

    注意：潮氣的散失也會隨滲透性的增加，風速的增加而增加，最終加快冷卻。
  12. The installed capacity of a generator is 777. 8mv ? a, air cooling is finally determined through analysis and comparing the advantages and defects for a variety of cooling ways and combining the features of longtan hydro - generator

    龍灘水電站水輪發電機單機視在功率達777 . 8mv ? a ，通過對各種冷卻方式優缺點的分析比較，並結合龍灘水輪發電機的特點，最終選用空冷方式。
分享友人
分享到 Line

分享到臉書