末端小管 的英文怎麼說

中文拼音 [mòduānxiǎoguǎn]
末端小管 英文
end-tube
  • 末 : Ⅰ名詞1 （東西的梢;盡頭） tip; terminal; end 2 （非根本、非重要的事物） nonessentials; minor detai...
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  • 小 : Ⅰ形容詞1 （體積、面積、數量、強度等不大） small; little; petty; minor 2 （年紀小的; 年幼的） youn...
  • 管 : Ⅰ名詞1 （管子） pipe; tube 2 （吹奏的樂器） wind musical instrument 3 （形狀似管的電器件） valve;...
  • 末端 : end; terminus; terminatio; terminal; tail end; extremity末端棒 terminal bar; 末端朝上 endways
  1. Lobular cis consists of a neoplastic proliferation of cells in the terminal breast ducts and acini

    小葉原位癌由末端乳腺導管與腺泡內的瘤性細胞增生形成。
  2. This neoplasm arises in the terminal ductules of the breast

    腫瘤見于乳腺末端小管。
  3. It spend 20 - 21 months from spermatogonial proliferation to spermiation. during this period, sperm live through the winter by storing in lumens at the end of testicular lobular or spermatic duct

    在此期間，成熟精子貯存在精巢小葉末端的管腔內或在輸精管內越冬，貯存期為7 - 9個月。
  4. For example, when the design flow of upward of the peace bridge of upward of the east - one main canal is 45m3 / s, the actual flow quantity is 23. 8m3 / s on the 30th of september in 1989, the water level of the transition region terminal of the mouth of hao wan flume of the east - one main canal had gained the design level of 4. 3m, and the level between downstream and shang tian yuan tunnel was generally higher. it says that the actual discharge capacity now is only about 24m3 / s which is half of the design value. this not only make the benefit of the irrigation district abnormal, but also greatly hinder the economic development of the irrigation district, and lead to the canal run frequently at small flow, high water level, lengthen the discharge duration

    如東一乾渠上段太平橋以上設計流量45m ~ 3 s ， 1989年9月30日實測通水流量23 . 8m ~ 3 s時，東一乾渠郝灣渡槽出口漸變段末端水位已達到設計水位4 . 3m ，其下游至上天院隧洞水位也普遍偏高，即東一乾渠上段目前僅能通過流量24m ~ 3 s左右，只有設計值的50左右，不僅使灌區效益得不到正常發揮，嚴重阻礙了灌區范圍內的經濟發展，而且使渠道經常處于小流量、高水位運行，延長了次通水時間，大大增加了渠道工程的安全管理難度。
  5. ( 3 ) the most principal factors that influence the supersonic atomization process include the flow ratio of the gas - liquid metal ( gmr ) value, the flow of atomizing of gas and the range of the inverse vortex taper. the more of the value of three factors, the more advantage they are for the atomization and the more fine the powders are. ( 4 ) the produced powders are the best in efficient atomization efficiency, particle diameter, particle shape and dispersion when the solder alloy is zhl63a, atomizing medium is n2, the protrusion h = 6. 0mm, atomizing gas pressure p = 100mpa, over - heat temperature t = 167 ( t = 350 )

    研究結果表明： （ 1 ）超音速霧化器的氣體流場在導液管下端形成一個倒渦流錐，在二維空間上呈軸對稱的雙峰分佈，負壓形成於這個倒渦流錐內； （ 2 ）修正後的霧化氣體速度公式可以滿足超音速霧化的要求； （ 3 ）影響超音速霧化工藝最根本的因素有氣液質量流率比（ gmr ）的大小、霧化氣體流量和倒渦流錐范圍，三個因素的值越大，對形成細粉越有利； （ 4 ）在焊錫合金為zhl63a ，霧化介質微n _ 2 ，導液管突出高度取h = 6 . 0mm ，霧化氣體壓力取p = 1 . 0mpa ，合金過熱度取t = 167 （ t = 350 ）時，所制得的粉末在有效霧化率、顆粒球形度、粒度及其離散度三個方面綜合性能最好。
分享友人
分享到 Line

分享到臉書