材積計算表 的英文怎麼說
中文拼音 [cáijījìsuànbiǎo]
材積計算表
英文
log rule- 材 : 名詞1 (木料) timber 2 (泛指可以直接製成成品的東西; 材料) material 3 (供寫作或參考的資料) ma...
- 積 : Ⅰ動詞(積累) amass; store up; accumulate Ⅱ形容詞(長時間積累下來的) long standing; long pending...
- 計 : Ⅰ動詞1 (計算) count; compute; calculate; number 2 (設想; 打算) plan; plot Ⅱ名詞1 (測量或計算...
- 算 : Ⅰ動詞1 (計算數目) calculate; reckon; compute; figure 2 (計算進去) include; count 3 (謀劃;計...
- 表 : Ⅰ名詞1 (外面;外表) outside; surface; external 2 (中表親戚) the relationship between the child...
- 計算 : 1 (求得未知數) count; compute; calculate; reckon; enumerate 2 (考慮; 籌劃) consideration; pla...
-
It is found that the effects of the latent heat are not negligible in the laser cladding process and their errors depend on the temperature range during phase transformations and the size of melted material region
計算結果表明,在激光塗敷過程的溫度場分析中,潛熱的影響不是總可以忽略的,其誤差取決于材料在物相轉變時交界面溫差的?圍及材料熔解體積的大小。The worm - like mesoporous materials were synthesized and characterized with tem, x - ray diffraction, nitrogen adsorption / desorption and ft - ir techniques, etc. the results showed that all the samples had larger porediameter than the samples through calcinations under resembled conditions, but the mesopore ordered poorly. ft - ir results showed hexagonal structural character were kept, but xrd, tem results showed that the samples have the structure characteristics of msu - x. it was analysized that all n2 adsorption isotherms of the samples belong to langmuir iv category which is related to mesoporous materials
Ft - ir光譜表徵結果顯示,經萃取處理后的介孔sio _ 2材料保持了六方的結構特徵;經xrd 、 tem進一步分析,證實所合成的介孔氧化硅材料具有msu - x材料的結構特徵, xrd譜圖表明樣品具有短程有序性:所合成的材料低溫n _ 2吸附測試結果表明,各樣品的n _ 2吸附等溫線均與中孔(介孔)特徵的第類曲線基本相符;由kelvin公式計算得到的孔徑分佈曲線說明,介孔材料具有較為集中的孔徑分佈;各樣品的bet比表面積比較高。A finite element analysis ( fea ) was eventually conducted, using mori - tanaka model and j - integral, to further explain the toughening mechanisms and fracture behaviour of the particle interleaved composites. the aim of the analysis was to examine the influence of the particle concentration and size, and the interaction between the particle and the crack tip. fea results indicate that interlayer zones can effectively lower j - integral and stress around the crack tip, and the high stress distribution in the region close to the interface can be the driving force for interfacial failure
本文的最後還藉助于有限元方法對層間增韌復合材料進行了宏觀和細觀斷裂韌性分析,基於mori - tanaka等效夾雜理論,計算了顆粒含量和尺寸對j積分的影響,有限元分析的結果同樣表明層間增韌可以有效的降低裂紋尖端應力水平,並暗示界面是可能存在的失效原因,所進行的數值分析起到了進一步支持和解釋增韌機理的作用。Examining results corresponding to different particulate geometry, it shows that the effective thermal conductivity not only depends upon the volume fractions and the properties of components, but also depends on the particulate geometry
對含有其它形狀夾雜的復合材料的計算結果表明,復合材料的有效熱導率不僅僅依賴于夾雜相的體積含量及組分性質,還與顆粒的幾何形狀有關。分享友人