板式給料機 的英文怎麼說

中文拼音 [bǎnshìgěiliàojī]
板式給料機 英文
apron feeder
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 式 : 名詞1 （樣式） type; style 2 （格式） pattern; form 3 （儀式; 典禮） ceremony; ritual 4 （自然科...
  • 給 : 給Ⅰ動詞1 （送對方某物; 使對方得到） give; grant 2 （用在動詞后 表示交與 付出） pass; pay 3 （叫; ...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 機 : machineengine
  1. Against to the outside of belt has installed the lever scraper cleaning device, it can remove adherent materials on the belt effectively

    給料機輸送膠帶的外側裝有杠桿式刮板清掃裝置，有效除去粘附在表面的物料。
  2. The spout feeder feeds the material, water, and grinding balls, into the mill and consists of a lined spout feeder, a feed trunnion liner, and a sandwheel assembly

    管式給料機將物料，水，球給入磨機，它由直線管式給料機，給料軸襯板，和砂輪組成。
  3. With the material dynamic constitutive equation including damage and the effect of stain rate the predictable formula about ballistic limit velocity of fiber composite target. secondly based on the damage feature about ceramic / fiber composite target caused by impact load, analysis model about defense performance of ceramic / composite material target is formed and the predictable formula about ballistic limit velocity is also given. lastly using the reflection and projectile theory of stress wave the paper discusses the design of ceramic / composite material target, optimizes the design of double layer ceramic / composite targets, gains optimal coefficient under certain area density and discusses the variety relationship of area density and thickness with optimal coefficient u nder some ballistic limit velocity 3

    首先，分析了纖維類正交鋪層復合靶板在沖擊載荷作用下的損傷破壞機理，結合包含損傷和應變率效應的材料動態本構方程，建立了纖維復合材料板彈道極限速度的預測公式；其次，根據陶瓷/纖維材料復合靶板在沖擊載荷下的破壞特點，建立了陶瓷/復合材料靶板抗彈性能分析模型，給出了彈道極限速度預測公式；最後，利用應力波反射和透射理論討論了陶瓷/復合材料靶板的設計問題，對雙層陶瓷復合靶板的優化設計進行了分析，給出了在一定面密度下的最佳優化系數，討論了一定彈道極限速度下的面密度和厚度隨優化系數的變化關系。
  4. We research on the thermal buckling characteristics of double layer membrane which is composed of different materials with different thermal expansion coefficiens under uniform temperature elevation. the energy method is proposed which is used to solve the problem and the symbolic relation between central buckling height and substrate height under small buckling height is also given. it is the primary theory of membrane resonant sensor, which makes the research and development of novel thermal sensor possible

    本文對微機械中熱脹系數不同的材料構成的雙層復合薄板在均勻溫升下的撓曲特性進行了研究，提出了在均勻溫升下雙層薄板熱撓曲求解的能量法，並給出了小撓度下中心撓度與板厚的解析關系，為薄膜諧振式傳感器溫度特性的研究和新型溫度傳感器的設計與開發打下了基礎
  5. And relying on this, our laboratory proposes a new cladding method. by means of large dynamic explicit fem code ansys / ls - dyna, the numerical simulation was carried out in bimetal forming process. during the simulation of the forming process, the large deformation of the strip should be considered, as well as geometrical and material nonlinear, the contact between the roller and the strip, the contact between two metal sheets and the load. as for these problems, we can use node to surface contact and relative parameters, biso model is introduced, the load is applied as array

    本文採用ansys / ls - dyna計算程序為分析工具，對鋸齒形雙金屬復合板成型過程進行計算機數值模擬，在對軋制過程模擬時，針對軋件變形的幾何非線性和材料非線性特點、軋輥與軋件間的接觸、軋件間的接觸以及模型的加載等問題，給出了在ansys / ls - dyna中相應的解決方法：應用nodetosurface接觸方式，設定相應參數，選用雙線性等向硬化模型，載荷作為array施加在剛體質心。
  6. Light - duty slat feeder

    輕型板式給料機
  7. Heavy - duty slat feeder

    重型板式給料機
分享友人
分享到 Line

分享到臉書