校驗數據 的英文怎麼說

中文拼音 [jiàoyànshǔjù]
校驗數據 英文
check digit
  • 校 : 校名詞1. （學校） school 2. （校官） field officer3. （姓氏） a surname
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 據 : 據Ⅰ動詞1 （占據） occupy; seize 2 （憑借; 依靠） rely on; depend on Ⅱ介詞（按照; 依據） according...
  • 數據 : data; record; information
  1. ( 2 ) the liman problem is normally adopted to check the liability of numerical method. the calculation error was within 9 % by comparison with the theoretic solutions of liman problem in the following case, the dimensionless calculation length was 2 with high pressure zone 0. 8, and the dimensionless state parameters were p1 = 2, p2 = 1, p1 = p2 = 1, u1 = u2 = 0. experiment results in literature [ 8 ] were used to check the adaptability of the numerical model developed here for unconfined gas cloud explosions and the calculation error was within 13 %

    （ 2 ）數值方法的可靠性通常用黎曼問題的解析解檢驗，本文以無量綱計算區長度為2 ，高壓區長度為0 . 8 ，狀態參數為p _ 1 = 2 ， p _ 2 = 1 ， _ 1 = _ 2 = 1 ， u _ 1 = u _ 2 = 0條件下的黎曼問題解析解對所編制的爆炸場計算程序進行了考核，結果表明該程序的計算誤差在9以內；為考核本文計算模型預測開敞空間氣雲爆炸的適用性，以文獻[ 8 ]的實驗數據進行了校核，計算誤差在13以內。
  2. Abstract : a new method for determining proximity parameters, and in electron - beam lithography is introduced on the assumption that the point exposure spread function is composed of two gaussians. a single line is used as test pattern to determine proximity effect parameters and the normalization approach is adopted in experimental data transaction in order to eliminate the need of measuring exposure clearing dose of the resist. furthermore, the parameters acquired by this method are successfully used for proximity effect correction in electron - beam lithography on the same experimental conditions

    文摘:在電子散射能量沉積為雙高斯分佈的前提下，提出了一種提取電子束光刻中電子散射參數，和的新方法.該方法使用單線條作為測試圖形.為了避免測定光刻膠的顯影閾值，在實驗數據處理中使用歸一化方法.此外，用此方法提取的電子散射參數被成功地用於相同實驗條件下的電子束臨近效應校正
  3. Data migration centralizes the research of verifying, extracting, transforming and loading data

    數據遷移主要研究數據校驗、數據清洗、數據轉換和數據加載等方面的問題。
  4. Abstract : this article discussed the causes of errors in nc program of machining screw using non - instant center envelope method. an analytical method to check the accuracy of nc program has been given, thus the theory basis of improving nc program has been provided in this article

    文摘:對目前常用的無瞬心包絡法螺桿加工數控程序中產生誤差的原因進行了分析研究，提出了一種校驗數控程序精度的分析方法，為改進數控程序提供了理論依據。
  5. Using the improved algorithm in edge location, the computing complexity is reduced by avoiding search efforts when using two dimensions error table, and the measuring accuracy is increased

    實驗數據表明，用誤差函數對定位邊緣進行誤差補償不但避免了使用誤差校正表帶來的復雜計算，而且重用性高，還大大提高了測量的精度。
  6. Which command verifies encapsulation as well as layer 1 and layer 2 statistics on a router configured for frame relay

    在幀中繼的配置中，哪一條命令可以用來校驗數據在第一層和第二層上的封裝形式
  7. This validation verifies that all of the elements individual pieces of data exist, are in the expected sequence, and are all of the correct data type

    該驗證校驗數據的所有元素（各片段）均存在，都按預期順序排列，並且均為正確的數據類型。
  8. A new transformer calibrator with dsp technique is designed by the paper, which improves the instrument integration, checkout accuracy and speediness

    本文應用dsp技術設計全新的互感器校驗儀，大大提高了其集成度和校驗數據的準確性和快速性。
  9. The code calibration is completed by comparing the numerical results with data from two experiments, one of which is test of a 2 - d hypersonic inlet with internal compression and the other a sidewall compression inlet. good agreement of numerical and experimental results proves the possibility and credibility of the numerical method

    利用國外文獻公布的二維進氣道實驗結果和本課題組側壓式進氣道炮風洞實驗獲得的實驗數據對本文的計算方法進行了校驗，證明了本文所採用的方法應用於高超聲速進氣道計算的可行性和可靠性。
  10. Based on the theory of system identification and experimental data, the simulating results of many kinds of parameter models have been compared. among them, we can find a parameter model that can precisely express the dynamic character of measurement system. on the system model constructed, the dynamic error of measuring data is processed by inverse filtering method

    本文先後對測試系統進行了多次動態校準，根據所得實驗數據在系統辨識理論的基礎上，比較了多種參數模型的模擬效果，尋找到一類能夠準確地描述測試系統動態特性的參數化模型，並根據所建立的系統模型，採用反濾波方法改進了測試系統的動態特性。
  11. The most commonly applied assay parameters accuracy, precision, detection limit, specificity, selectivity, calibration linearity or nonlinearity, stability, recovery, reproducibility and repeatability are carefully defined along with some recommendations required for assessing data acceptability arrived at the conference on analytical methods validation

    美國分析方法認證會議曾推薦用分析參數（準確度，精密度，檢測限度，專屬性、選擇性、校準線性或非線性、穩定性、回收率、重演性與重覆性）作為判斷實驗數據的可采納性。
  12. It compares and analyses the equipment test voltage emendated to standard atmosphere conditions with the equipment nominal withstanding voltage. and then it concluded that : the emendation value educed by " humidity ratio " integrated emendation method is basically equal or close to the equipment nominal withstanding voltage ; but the values by two traditional emendation methods are mostly higher. it also proves that, " humidity ratio " integrated emendation method is more perfect than any other methods, and it can reflect the influence degree of atmospheric parameters on electrical equipment outer insulation discharge voltage actually

    文中選擇「比濕」綜合校正法和兩種傳統校正法，分別對西高所為羊八井、拉薩、羊湖110kv變電所設備所做的人工氣候室模擬試驗數據及雲南中試所做的zs - 110工頻放電電壓試驗數據進行校正計算，將試驗電壓的校正值與試驗設備的標稱耐受電壓水平進行比較分析；認為： 「比濕」綜合校正法的校正值與設備耐受電壓水平基本相等或接近，而兩傳統校正法的校正值大多高於設備耐受電壓水平；進一步證明， 「比濕」綜合校正法是目前諸多校正法中較為完善的，能真實地反映大氣參數對電氣設備外絕緣放電電壓的影響程度的校正法，在高海拔電力工程設計中應推廣應用。
  13. Crc technology is adopted to verify data and guarantee the dependability in the wireless communication

    採用crc校驗技術檢驗數據，以保證通信的可靠性。
  14. A bit added to a binary code that indicates parity and is used to check the integrity of data

    奇偶校驗位加在二進制碼上的一個標明奇偶數的位，用於檢驗數據的完整性
  15. 3. a series of quasi - dynamic calibration tests by varying the pressure pulse width for the < t > 3. 5 x 8. 75mm pillar copper cylinders and o 4. 763mm copper spheres are done on the dropper - hammer hydraulic dynamic pressure calibration device. by means of data analysis, the regulations of pulse width ' s effect on the two types of plastic pressure - measuring elements are obtained

    3利用落錘液壓動標裝置組織了3 . 5 8 . 75mm柱形銅柱、 4 . 763mm銅球的變脈寬準動態校準試驗，通過試驗數據處理，獲得了兩種型號塑性測壓器件的脈寬影響規律。
  16. Using experiment results as standardized data, the frequency responses collected by seafloor magnetotelluric measurements can be corrected to produce authentic information about the seafloor field source

    實驗數據可作為標定資料，對海底大地電磁探測的實測信號進行校正後，即可還原出真實的海底場源信息。
  17. People can select baud rate, parity check, data bits and stop bits to match with the diverse communication requirements. 3

    用戶可選擇波特率、奇偶校驗、數據位等通信格式，適應採集系統不同的串列通信要求。
  18. After processing the collected data, the results are reached as follows : most students except those from no. 30 middle school which is interfered by the educational experiment seldom participate in voluntary activities. students who often participate have significant difference with those who seldom participate in the aspects of social responsibility, self - efficacy, altruistic attitude, and moral behaviors. the difference in the moral judgment is not significant

    通過對實驗數據的統計分析發現，除經過教育干預的30中以外，大多數學校的學生很少參加志願服務活動；經常參加志願服務活動的學生與不經常參加的學生相比，在社會責任感、自我效能、利他態度和道德行為方面存在顯著的差異；在道德判斷上差異不顯著；幫助老人、保護環境、宣傳、捐贈等志願服務項目都分別和社會責任感、利他態度、自我效能、道德行為存在著不同程度的相關。
  19. Job description : clinical data into clinical trial databases from images or electric file ( i. e. case report forms, laboratory reports, translation data list )

    負責將各類圖象或電子文本（如:病歷報告表格，實驗報告，數據轉換清單）中的臨床數據信息輸入到臨床試驗數據庫中並完成校對
  20. The data processing associate ( dpa ) enters and verifies clinical data into clinical trial databases from images or electric file ( i. e. case report forms, laboratory reports, translation data list )

    負責將各類圖象或電子文本（如:病歷報告表格，實驗報告，數據轉換清單）中的臨床數據信息輸入到臨床試驗數據庫中並完成校對
分享友人
分享到 Line

分享到臉書