核心檢測程序 的英文怎麼說

中文拼音 [héxīnjiǎncèchéngxù]
核心檢測程序 英文
kernel program
  • 核 : 核構詞成分。
  • 檢 : Ⅰ動詞1 （查） check up; inspect; examine 2 （約束; 檢點） restrain oneself; be careful in one s c...
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 核心 : core; kernel; kern; heart; centre; elite; nucleus
  • 檢測 : check; detection; test; gauging; detecting; sensing; [工業] checkout; measuring
  • 程序 : 1 （進行次序） order; procedure; course; sequence; schedule; ground rule; routing process 2 [自動...
  1. In the part of detector, it mainly introduces the design of liquor tubes, heater, pressurize, and thermocouple ; in the part of controller, this design uses tms320lf2407 as the cpu. the design part mainly introduces controller circuit design which mainly contains data collection circuit, prepositive magnifying circuit, a / d convert circuit, failure self - diagnosis circuit, the tms320lf2407 interface circuit, temperature control circuit, display circuit, 4 ~ 20ma standard signal output circuit ; in the software part, it mainly introduces software chart of main program and partly linearization subprogram design

    檢測器部分重點介紹了導流管的設計、加熱器的設計、密封技術的設計以及測溫電路的設計;控制器部分以tms320lf2407為核心，重點介紹了控制器電路設計，主要包括數據選擇電路、前置放大電路、 a / d轉換電路、故障自診斷電路、 tms320lf2407介面電路、控溫電路、顯示電路、 4 20ma標準信號輸出電路共八個部分;軟體設計重點介紹了主程序軟體設計及分段線性化子程序設計。
  2. A digital automatic ultrasonic inspection system designation is introduced. this system was developed with pc computer and embedded dsp, combining computer software and hardware, ultrasonic nondestructive testing, digital signal processing, embedded rtos and visual instruments technology. it meet the requirements of automatic inspection such as high repetitively frequency and real time alertation

    該方案以pc機和dsp系統為核心構成主從機系統框架，以基於虛擬儀器思想的pc機應用程序和基於dsp的嵌入式實時操作系統構成雙重軟體結構，把傳統的超聲波無損檢測技術和先進的虛擬儀器技術、數字信號處理技術、嵌入式實時操作系統、計算機介面通信技術相結合，從而滿足了自動化探傷中1k / s的重復頻率和實時報警的要求。
  3. At last, we draw out some core modules of pems. directed by theories and methods of software reliability, we use static check tools pc - lint and splint to check those modules, and write some programs to test them

    最後，抽取pems的核心模塊，應用可靠性理論和方法，使用靜態檢測工具pc - lint和splint對這些模塊進行檢測，開發測試程序進行測試。
  4. First of all, this paper introduces the whole design project and interrelated knowledge about non - destructive detection, ultrasonic detection, and phased - array ultrasonic detection then the paper depicts the principle of phased - array focus and abstracts a set of math model and feasible arithmetic on the base of the real parameter of the system. put forward several problems that exist during the course of system development and program. introduce some measures of distinguish that are often used in non - destructive detecting and echo wave crest

    然後在文中以較大的篇幅，描述了相控陣聚焦的原理，並根據該系統的實際參數，抽象出一套數學模型和可行的演算法，在此基礎上提出了在系統開發過程及編程實現過程中存在的一些問題；介紹了在無損檢測中缺陷的分類和對回波峰常用的識別方法，詳述了系統開發過程中使用的其中一種識別方法，即判別是否存在缺陷的演算法，並給出實現之的部分核心程序；詳述主控程序如何控制各部分並協調各相關軟體的工作，使整個系統發揮最高效能，並給出主要設計框圖和程序。
  5. Therefore, through comparing schemes, we select the ultralow power, high integration msp430f43x series microcontrollers as the center. on software, we take full advantage of the low power modes of the mcu to finish the task in isr ( interrupt service routine ), so, the power of system rest with the isr executive time

    因此，在硬體選擇上，通過方案比較，選用微功耗、高集成度的msp430f43x系列單片機作為控制核心；在軟體設計上，充分利用所選單片機的低功耗模式，讓檢測任務在中斷服務程序中完成，使系統的功耗主要取決于中斷服務程序執行的時間。
分享友人
分享到 Line

分享到臉書