梁箍筋 的英文怎麼說

中文拼音 [liánggūjīn]
梁箍筋 英文
beam stirrup
  • 梁 : 名詞1 （屋架中架在柱子上的長木） beam 2 （通常也指檁） purlin 3 （橋） bridge4 （物體中間條狀隆起...
  • 箍 : Ⅰ名詞（緊緊套在物體外面的圈） hoop; ferrule; band Ⅱ動詞（用竹篾或金屬條捆緊; 用帶子之類勒住） bin...
  • 筋 : 名詞1 （肌的舊稱） muscle2 [口語] （肌腱或骨頭的韌帶） tendon; sinew 3 [口語] （可以看見的皮下靜...
  1. Here the hsc of sompa is achieved through adding super - effective water reducer, fined slag and silicon fume, and decreasing the water / cement ratio. by varying the area ( spacing ) of tension bars, compressive bars, vertical links and distribution steel and embedding steel fiber and polypropylene fiber we try to improve the behaviors of reinforced high performance concrete one - way spanning slabs in bending, so that its ductility be greater than 5. with the same arrangement of steel the width of bending member is varied to observe the effect of the width / depth ratio on the ultimate compressive strain of concrete

    通過變化受拉筋含筋率和受壓筋、箍筋（鉤筋、分佈筋）含量，或摻加纖維使之成為鋼纖維高強混凝土（ sfrhsc ）和聚丙烯纖維高強混凝土（ pfrhsc ） ，對高強混凝土雙筋截面梁、板的受彎性能進行了試驗研究，試圖改善高強混凝土受彎構件的延性，使其延性比大於5 ；並在相同配筋情況下，通過變化截面寬度，研究了高強混凝土受彎構件的寬高比對壓區混凝土極限應變的影響；並對試驗構件的裂縫發展情況進行了觀測。
  2. It also has important reference value for the similar construction. by the safety and seismic evaluation of this aqueduct bridge, it has shown that ( 1 ) besides the structure of this aqueduct bridge was basically unharmed without some flake of concrete cover and revealing stirrup, its intensity basically reached the need of primary design. ( 2 ) from the side of carrying capacity, rib arch could satisfy the needs under the action of wind and earthquake, but some individual frame crossbeams and most rib arch tie beams could n ' t satisfy the need

    通過對東滑峪渡槽進行安全性能和抗震性能評估后表明： （ 1 ）渡槽除肋拱頂面有保護層剝落、箍筋外露，結構基本完好，其強度基本達到西安理工大學工程碩士專業學位論文原設計的強度要求； （ 2 ）從承載力方面看，在風荷載、地震作用下，肋拱基本滿足要求，個別排架橫梁不滿足要求，肋拱連系梁普遍不滿足要求；計入水平橫槽向地震作用的工況為設計控制工況。
  3. Secondly, this paper made some theoretic researches on its engineering classfication and applicable scope for this technology ; then combining with project example, this paper carried out scheme design for this technology, and compared some different kinds of underpinning scheme and node and structure design, and put forward the method of " reinforcce steel bar through column " to build pile cap beam, " resistant bend and shear anchored reinforce steel bar " to strengthen column consolidation effect, and the method of " steel plate hoop " to build reinforcing bar connection of the foundation beam, etc. in the process of the consturction scheme research and implement, this paper synthetically elaborated the organizaton for project construction, put forward the construction technical measure of specific aim on the artificial pile, and pile cap beam, and underground adding layer and structure stabilization, and overall structure stabilization and so on. for this project, adopt reinforcing bar concrete to brace hole wall to ensure the safety of engineering in the artificial pile construction, use flexible connection catch to make the cage hoisting easier to simplify the construction process, use the method of earthwork statified symmetrical balance in the process of underground adding layer excavation

    本文首先對于基礎托換與結構加固技術的目的和意義、國內外發展狀況進行了綜合闡述；其次對該項技術工程分類及適應范圍進行了理論上的分析研究；然後結合工程實例對該項技術進行了方案設計，對比幾種不同的托換方案和節點及構造設計，提出了「通筋穿柱法」做承臺梁， 「抗彎抗剪錨筋法」強化柱加固效果， 「鋼板箍法」做地基梁鋼筋連接點等多項技術；在施工方案的研究和實施過程中，對于工程施工組織進行綜合闡述，並就人工挖孔樁、承臺梁、地下加層及結構加固、整體結構穩定等專項施工方案提出有針對性的施工技術措施，人工挖孔樁施工採用鋼筋砼護壁確保挖孔樁的安全成型，使用柔性連接鉤進行鋼筋籠吊裝簡化施工工序；承臺梁施工採用梁主筋橫穿柱身化學膠錨固等；地下加層綜合施工技術採用土方分層對稱平衡開挖，分段挖土做筏基結構自穩等；最後對于該工程實施后的效果分析，說明該項綜合施工技術的可行性。
  4. The research shows that : 1 ) the ductility of the hsc bending members constructed is much greater than 5 ; 2 ) increasing the vertical links and distribution steel can increase the deflection under ultimate moment ; 3 ) with appropriate compressive bars, vertical links and distribution steel the increase of moment after yield and the decrease of moment under ultimate moment can be ignored, so the ductility of the hsc bending member is much larger ; 3 ) the width / depth ratio of hsc bending member has no obvious effect on the ultimate compressive strain of concrete ; 4 ) the method used here to calculate the deflection is applicable ; 5 ) the location of crack coincides with the location of vertical links and distribution steel ; 6 ) the bending property of the hsc structure under the blast load can meet the demand of protective engineering

    研究表明：本文研究的梁、板構件的延性比遠大於5 ；增加箍筋（鉤筋、分佈筋）含量，可以提高壓區混凝土剝落時的撓度；在適當的受壓筋、箍筋（鉤筋、分佈筋）含量下，可以忽略壓區混凝土剝落瞬間的承載力下降，從而大大提高構件的延性；受彎構件的寬高比對壓區混凝土極限應變的影響不明顯；受彎構件的裂縫間距受箍筋（鉤筋、分佈筋）的布置影響；文中所用的承載力和變形計算方法是可行的。化爆試驗表明，高強混凝土構件的動載抗彎性能能夠滿足防護結構的要求。
  5. Based on measurement of strains of both horizontal stirrups in the joint core and longitudinal reinforcement passing througth the joint, in different stages, transfer mechanism and factors affacting seismic behavior of the joint, were analysed. under different shear compression ration, effect of axial force ratio on seismic behawior of the joint was also evaluated, static shear and seismic shear of the joint based on capacity design were investigated. on this basis, new governing criteria and conditions of seismic behavior of the joint were put forward

    通過對節點區水平箍筋以及貫穿節點梁、柱縱筋在不同受力階段應變的精細量測，對節點的傳力機理以及影響抗震性能的因素進行了分析研究；對不同剪壓比條件下軸壓比對節點抗震性能的影響規律進行了分析研究；對不同受力階段梁筋的粘結退化規律以及節點區的剪切變形進行了分析研究；對節點的靜力抗剪與建立在能力設計思路上的抗震抗剪問題進行了深入研究，提出了建立在新思路基礎上的節點抗震性能控制準則和控制條件。
  6. The difference between axial compressive capacity of beam - column joints and that of columns is introduced when joints are strengthened by various measures. influence of shapes, spiral hoops and ratio of beam depth to side dimension of square column upon axial compressive capacity of beam - column joints is discussed. then economy and security of the relative article in current code are demonstrated and the design recommendations of beam - column joints are given

    本文通過6個不同強度等級混凝土樑柱節點試驗，了解在不同的加強措施情況下，節點區的軸心抗壓承載力與柱的理論軸心抗壓承載力的差異，探討了角鋼、螺旋箍筋及梁高與柱截面尺寸的比值h c對節點區軸心抗壓承載性能的影響，驗證了我國現行規范有關條款的安全性和經濟性，並且在此基礎上，為不同強度等級混凝土樑柱節點的設計提出了相關建議。
  7. There is not composite enhancing effect to shear resistance of reinforced concrete beams between steel fiber and stirrups

    鋼纖維與箍筋之間在提高鋼筋混凝土梁斜截面承載力方面不存在「藕合增強效應」 。
  8. ( 3 ) the beam stirrups are very important to the anchorage of the upper longitudinal bar in the beam outside the wall " s width

    節點區的寬梁箍筋對于凸出在墻外的寬樑上部縱筋的錨固具有比較重要的作用。
  9. According to the test of the shear beams reinforced with the stirrup of hrb400 steel bars, the mechanical property of stirrup in the members is studied

    通過hrb400級鋼筋作箍筋的不同剪跨比的受剪梁的試驗，分析了此類鋼筋作箍筋的受力情況。
  10. If the quantity of the beam stirrups is not enough, the wide beam would have more crack in the joint area thus decrease bearing capacity and ductility of joints

    如果節點區的寬梁箍筋數量不足，寬梁在節點區將出現較多斜裂縫，最終使結構的承載力和延性變差。
  11. The minimum shear resistance of beams in the paper is close to the one in the code for design of concrete structures " gb50010 - 2002 '. according to the actual project, the destroy of 448 kinds of beams are analyzed by computer by taking account of the effective coefficient " " of the strength of concrete confined by hoops, the relationship with the section property of beams, the critical point of the arch - rib failure transiting to the shear - compression failure which is advanced in the anti - theory, and the contribution to the beam ' s shear resistance of the concrete in the shear - compression zone

    引用箍筋約束混凝土的有效系數，利用其與梁截面特性的關系並結合理論分析中提出的梁剪壓破壞與斜壓破壞的分界點，同時考慮了剪壓區混凝土的抗剪貢獻，從工程實際出發，編程擬算了448種梁構件的破壞情況，計算結果表明，梁發生在剪壓破壞范圍內的最大抗剪承載力值比混凝土結構設計規范gb50010 - 2002值略高。
  12. At first, development of various cracks carefully recorded and strains on both the rebars and the stirrups were measured in detail, together with the deflections of the beam. in such a way, correlation between the measured strain profiles of the reinforcement and the observed cracking development of each specimen was pursued. principal factors contributing to the cracking pattern and failure mode were figured out as a result

    首先，通過單調靜力加載試驗研究，對梁的裂縫延伸和開展、縱筋應變、箍筋應變、梁的撓度等指標進行了細致的量測，試圖追蹤每一試件在裂縫發展及破壞過程中縱筋應變狀態的變化和裂縫發展程度的相關性，進而總結出有腹筋約束梁裂縫開展及鋼筋應力分佈的一般規律。
  13. At this background, though coupling beams with the small ratio of the span to depth have no sufficient test results, in order to satisfy the needs of engineering design, the code for design of reinforced concrete high - rise structure ( jgj3 - 2002 ) still adopt the design method of decreasing the maximum shear force and increasing the quantity of stirrups. but in china code for design of concrete structures ( gb 50010 - 2002 ) the content of seismic design methods for these kinds of coupling beams continue to be blank

    在這一背景下， 《高層建築混凝土結構技術規程》 （ jgj3 - 2002 ）為了滿足工程設計需要，對小跨高比連梁在沒有充分試驗結果的情況下，仍採用降低最大作用剪力和提高箍筋用量的設計方法（雖然這種方法已被國外試驗證明在跨高比小於1 . 50的連梁中是肯定不能保證延性要求的） ，而《混凝土結構設計規范》 （ gb50010 - 2002 ）則把這部分內容繼續留作空缺。
  14. ( 2 ) based on deterioration model of owerage bond stress of beam reinforcement accounting for effect of axial compression ration and number of displacement loops, and stress - strain relationship of the concrete in the joint core accounting for effects of both softening and confinement, the modified compression field theory was employed to simulate behavior of the joint core under loading reversals. analysis by means of the program jap on the tested specimens in this paper and those obtained from other researchers produced consistent results

    根據本文建立的考慮軸壓比和位移循環次數影響的梁筋平均粘結應力退化模型和考慮軟化效應、約束效應的核心區混凝土應力應變關系，通過在試驗中得出的節點核心區混凝土、箍筋、節點正面、背面柱筋在反復荷載下的受力特點，利用斜壓場理論模擬節點核心區在反復受力過程中的受力狀態。
  15. 3 the results denote that for non - flanged slw, when the limb is shallow, the longitudinal bar in the limb will firstly yield ; on the other hand, when the limb is deep, the stirrup in the linking - beam will firstly yield

    對于無翼墻結構，當肢厚比為5時，試體墻肢底部縱筋首先屈服，而當肢厚比大於5時，試體連梁端部箍筋首先屈服。
  16. The objective function is the cost of anti - slide pile " s per meter ; the constraint conditions are the strength of anti - slide pile " s normal section and inclined section, the ratio of reinforcing design and the size of section in the design code ; the design variables are the height of section, the area of reinforcement and the amount of hoop. and the optimization model is solved by 0. 618 method

    本文提出的優化設計方法，以樁單位長度的總造價為目標函數，以規范對單筋梁的正、斜截面強度，配筋率及截面尺寸等要求為約束條件，以樁截面高度，抗彎縱筋面積，抗剪箍筋數量等為設計變量，來建立優化模型，並用0 . 618法進行求解。
  17. The shear strength of the no corroded rc beams with stirrups is divided by two parts, that is the strength provided by the stirrups and the beams without web reinforcement. on the basis of this shearing mechanism of rc structural elements with web reinforcement, considering the confining effects of the stirrups, the shear carrying capacity expression of the corroded rc structural elements is given. the present results are compared with corresponding references and some reasonable conclusions are drawn

    對于銹蝕有腹筋梁的抗剪承載力問題，基於未銹蝕有腹筋梁抗剪強度公式建立的原理，即未銹蝕有腹筋梁的抗剪強度為相應未銹蝕無腹筋梁的抗剪強度和箍筋對梁抗剪強度貢獻兩部分的疊加，考慮箍筋的約束作用對斜截面抗剪強度的貢獻，建立了有腹筋構件斜截面抗剪承載力的計算表達式，且與相關文獻的結果進行了比較。
  18. An equation to calculate ultimate shear - resistant capacity of src column and steel beam joint is discussed, with consideration of the actions of concrete, steel web and horizontal hoop. the effects of axial press and steel wing under loads are also discussed

    探討考慮混凝土、型鋼腹板、箍筋共同貢獻的勁性柱?鋼梁節點極限抗剪承載力計算公式，並就軸壓力、翼緣在節點受力過程中的作用進行了分析與評價。
  19. First, the paper sets up finite element models of 4 - point bending rc beam strengthened with frp sheet. not only material nonlinear of concrete and steel bar but bond style of longitudinal steel, stirrup and frp are taken into account

    本文首先建立了纖維布加固鋼筋混凝土梁四點彎曲的有限元模型，考慮了混凝土、鋼筋的材料非線性以及縱向鋼筋、箍筋和纖維布與混凝土之間的聯結關系。
  20. 2. based on the test results published over the word of steel fiber reinforced concrete beams without web reinforcements and with stirrups, the effects of steel fiber to shear resistance and the relationship of steel fiber to stirrups are analyzed, the improvements of steel fiber to failure states of reinforced concrete beams without web reinforcements are discussed. it is proposed that the formula of shear resistance of steel fiber reinforced concrete beams based on the model of the current design and construction spectification of steel fiber reinforced concrete structures ( cecs38 : 92 ), used of the uniaxial tensile strength of steel fiber reinforced concrete, and combined with different formulas specified in current design codes of concrete structures issued by different trades

    根據收集到的國內外對鋼筋鋼纖維混凝土無腹筋梁和鋼筋鋼纖維混凝土有腹筋梁的斜截面受力性能試驗研究成果，對鋼纖維在增強鋼筋混凝土無腹筋梁和有腹筋梁斜截面承載力方面的作用及其在箍筋抗剪承載力的關系進行了總結分析，對鋼纖維改善鋼筋混凝土梁破壞形態方面的作用進行了分析討論，提出了採用鋼纖維混凝土軸心抗拉強度指標，基於現行cecs38 ： 92 《鋼纖維混凝土結構設計與施工規程》計算模式、能夠與目前國內各行業現行混凝土結構設計規范中不同的鋼筋混凝土梁受剪承載力設計方法配套使用的鋼筋鋼纖維混凝土梁受剪承載力設計方法。
分享友人
分享到 Line

分享到臉書