極限尺 的英文怎麼說
中文拼音 [jíxiànchǐ]
極限尺
英文
dimension limit- 極 : i 名詞1 (頂點; 盡頭) the utmost point; extreme 2 (地球的南北兩端; 磁體的兩端; 電源或電器上電流...
- 限 : Ⅰ名詞(指定的范圍; 限度) limit; bounds Ⅱ動詞(指定范圍, 不許超過) set a limit; limit; restrict
- 尺 : 尺名詞[音樂] (中國民族音樂音階上的一級 樂譜上用做記音符號 參看「工尺」) a note of the scale in ...
- 極限 : 1 (最高的限度) the limit; the maximum; the ultimate limit; limitation; extremity; tipping point...
-
Railway transport equipment. berne key operated sockets. dimension limits
鐵路通用器材.鍵控制的套筒.尺寸極限Mj threads - limit dimensions for bolts and nuts
Mj螺紋.螺栓和螺母的極限尺寸Upper limit size
最大極限尺寸Iso metric trapezoidal screw threads ; limiting sizes for nut threads from 8 to 100 mm nominal diameter
Iso米制梯形螺紋.標稱直徑8 100mm螺母螺紋的極限尺Iso metric trapezoidal screw threads ; limiting sizes for bolt threads from 8 to 100 mm nominal diameter
Iso米制梯形螺紋.標稱直徑8 100mm螺栓螺紋的極限尺Rounded trapezoidal threads ; limiting screw thread dimensions and allowances ; permissible deviations and permissible wear of thread gauges
倒圓角的梯形螺紋.第2部分:螺紋極限尺寸與公差.螺紋Round screw thread with clearance and steep flank with pitch 7 mm ; limiting dimensions of screw threads and allowances - permissible deviations and permissible wear of screw thread gauges
螺距為7mm的帶公差和斜側面的圓螺紋.螺紋的極限尺寸Edison thread for d - type fuses ; limit dimensions
D型熔斷器的圓螺紋.極限尺寸Construction drawings - indication of limit deviations iso 6284 : 1996
技術圖樣.建築圖樣.極限尺寸標注Unj threads - general requirements and limit dimensions
Unj螺紋.一般要求和極限尺寸Mj threads - limit dimensions for fittings for fluid systems
Mj螺紋.流體系統用的接頭的極限尺寸Aerospace. mj threads. part 3 : limit dimensions for fittings for fluid systems
航空航天. mj螺紋.第3部分:流體系統連接件極限尺寸Aerospace ; mj threads ; limit dimensions for bolts and nuts ; identical with iso 5855 - 2 : 1988
航空航天. mj螺紋.第2部分:螺栓和螺母的極限尺寸;等I aerospace - mj threads - part 3 : limit dimensions for fitting for fluid systems iso 5855 - 3 : 1988
航空航天. mj螺紋.第3部分:流體系統配件的極限尺寸Valves for vehicle tyres ; valve screw threads ; theoretical values, limiting dimensions of screw threads
機動車輪胎的氣門.氣門螺紋.理論值.螺紋極限尺寸Miniature screw threads. limits of sizes
小螺紋極限尺寸Iso - metric screw thread ; screw threads below 1 mm diameter ; limits
Iso米制螺紋.直徑小於1mm的螺紋.極限尺寸Maximum limit of size
最大極限尺寸Minimum limit of size
最小極限尺寸Iso general purpose metric screw threads - tolerances - limits of sizes for internal screw threads to mate with hot - dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
Iso普通米制螺紋.公差.第5部分:與鍍鋅前公差帶位置為h最大尺寸的熱浸鍍鋅外螺紋相匹配的內螺紋的極限尺寸分享友人