極限量 的英文怎麼說
中文拼音 [jíxiànliáng]
極限量
英文
limiting discharge-
Fig. 8. 15 shows some experimental results for limiting adhesion against creep.
圖815表示試驗得出的極限粘著力對爬動量的關系。This time, however, i thought, if i can pass the ball across the court to the center forward, that will stretch my strength to its maximum capacity. but then i immediately became skeptical and thought, ive been skipping lunch lately and eaten very little at my other meals
我想這次如果能把球傳到中鋒手中,也算是我能力的極限了,但隨即又想:這些日子都不吃午飯,其他時候的食量也很少,怎麼會有足夠的勁道呢?By analyzed interactions of combined limit pipe load components, simplified check formula for pipe load strength are put forward and the calculation method of relevant allowable pipe load values based on shell finite element analysis is presented as well
通過對組合極限接管載荷分量相互關系的分析,提出了接管載荷強度驗算簡化公式和以殼結構有限元應力分析為基礎的許用接管載荷計算方法。On the basis of investigations into the progressive yield process and the possible failure modes of rcc gravity dams, the quasi - elasticity design limit state of the ctrtical stability criterion is proposed and the real working state of the dams designed according to the ctriterion is discussed. a check formula using the material strength reducing factor as the safety index and a simplified formula similar to against sliding stability fromula are derived. finally, the corresponding design safety factors are given by using fem calculations with various influence parameters to be taken into account
本文在研究碾壓混凝土重力壩漸進破壞過程和可能失穩方式的基礎上,提出了以準彈性臨界作為穩定臨界準則的設計極限狀態,分析了按該準則設計的大壩的實際工作狀態,導出了以準彈性強度儲備系數為設計安全指標的審查公式以及形式與抗剪斷公式相同的簡化公式,探討了定量計算考慮各種因素影響的相應設計安全系數的合理取值,並與現行規范方法進行了比較Infernal affair trilogy ultimate collectable boxset limited edition
無間道終極珍藏系列限量版At the same time, i discover that the number of the return air inlet has a little influecing and it can be neglected. when there is hot resource at upperside of the room, the hot jet and supply air jet together affecting. at the same lower part heat intensity, a utmost wind speed exist, the supply air speed lower, the more heat intensity on the upside, the less convecting transfer heat, whereas
對于上部有熱源的條件下,則其對流熱轉移量的變化關系是由熱射流與送風冷射流共同作用影響的,在下部熱源強度相同的條件下,存在一極限風速,在該風速以下,上部熱源強度越大,則對流熱轉移量越小,反之在該風速以上,上部熱源強度越大,則對流熱移量越大。Earth - moving machinery - laboratory evaluations of protective structures - specifications for deflection - limiting volume
土方機械.防護結構的實驗室評定.撓曲極限量規范The promise limited edition
無極限量版Inspection of tolerances of plain workpieces. limit gauges. tolerances and permissible wear of manufacture limit gauges up to 500 mm
普通加工件公差的檢驗.極限規.製造用公差與允許磨損量在500mm以下的極限量規Pipe threads where pressure - tight joints are not made on the threads - verification by means of limit gauges
非螺紋密封連接的管螺紋.用極限量規檢驗Pipe threads where pressure - tight joints are made on the threads - verification by means of limit gauges
螺紋上有壓力密封接縫的管螺紋.用極限量規驗證Pipe threads where pressure tight joints are made on the threads - part 3 : verification by means of limit gauges
用螺紋密封的管螺紋.第3部分:用極限量規檢驗Limit gauges for unified screw threads
統一螺紋極限量規This article analyses by micro - economical theory the added throwing for establishing a new social order pattern during the modernization of the legal system and the lost benefit for denying the old social order pattern, and describes the new cost and benefit for modernization of legal system, the cost formation and the maximum and minimum of costs as well as the seeing criteria of the amount limit
對法制現代化過程中,為建立新的社會秩序模式而增加的投入,和因否定舊社會秩序模式而失去的效益等,運用微觀經濟學理論進行了分析,描述了法制現代化成本與效益、成本構成以及成本的上下限及極限量的參照標準。Specification for limits and tolerances on plain limit gauges
普通極限量規的極限和公差規范Verification regulation of smooth limit gauge
光滑極限量規檢定規程Types and dimensions of plain limit gauges
光滑極限量規型式和尺寸Gauge blanks for screw threads limit gauges
螺紋極限量規的塊規Limit gauges for metric screw threads
公制螺紋極限量規Plain limit gauges
普通極限量規分享友人