標稱厚度 的英文怎麼說

中文拼音 [biāochènhòudù]
標稱厚度 英文
nominal thickness
  • 標 : Ⅰ名詞1 [書面語] （樹梢） treetop; the tip of a tree2 （枝節或表面） symptom; outside appearance; ...
  • 稱 : 稱動詞（適合; 相當） fit; match; suit
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. Nominal insulated thickness

    標稱絕緣厚度
  2. Nominal thickness of insulatioh should be in accordance with the stipulations of table 1, table2. - 10 % discrepancy is allowed, but the minimum thickness should be not less than 90 % - 0. 1 of nominal thickness

    2絕緣絕緣標和厚度符合表1 、表2的規定，允許有- 10 %的偏差，其最薄厚度應不小於標稱厚度的90 % - 0 . 1
  3. Standard test method for measuring nominal thickness of permanent rolled erosion control products

    永久滾軋防腐蝕產品的標稱厚度的測量的標準試驗方法
  4. In upper level optimization, the thickness and geometry factors of composite skins and webs as well as other structural dimensions are taken as design variables. then, considering the behavior constraints and the side constraints, the structural mass is minimized by the mathematical programming technique. in lower level optimization, the mathematical programming technique or the genetic algorithm ( ga ) is used to search the practical stacking sequence of composite skins and webs to realize the given thickness and geometry factors from upper level optimization

    底層優化設西北工業大學博士學位論文計以復合材料蒙皮和腹板等層合板各分層的厚度（或鋪層數） 、鋪層角和鋪層順序為設計變量，以層合板的幾何因子與頂層優化設計給出的最優幾何因子之間的誤差最小為目標，考慮層合板厚度和製造工藝性約束，採用數學規劃方法或遺傳演算法（ geneticalgorithm ，簡稱ga ）求出底層最優設計變量。
  5. Nominal sheath thickness

    標稱護套厚度
  6. All boards and planks must be cut sufficiently full to stand the nominal thickness after kiln drying to 8 % moisture contents

    拙譯：所有木板必須經充分切割，使其標稱厚度可以承受濕度為8 %的烘烤。
  7. Nominal thickness of jacket

    護套標稱厚度
  8. Insulated nominal thickness

    絕緣標稱厚度
  9. For a sheet of nominal thickness not listed in the table, the permissible variations shall be the same as the next greater thickness

    對于標稱厚度不在所列的優選厚度之一者，其允許偏差應採用下一個較大的優選厚度的偏差。
  10. Tinned flexible copper wire is used as conductor, and its structure and d. c resistance should be in accordance with the stipulations of table1. table2

    2絕緣絕緣標和厚度符合表1 、表2的規定，允許有- 10 %的偏差，其最薄厚度應不小於標稱厚度的90 % - 0 . 1
  11. The name and the code name of the pipeline, pipe material, o. d. and the thickness of pipe, transmitting medium and its temperature, insulator materital and its thickness, the orientation of the pipeline, hight of pipe center

    管線名稱代號，管道材質、外徑和壁厚，輸送的介質及其溫度，絕熱層材質及厚度，支吊處管線走向，管中心（管底）標高。
分享友人
分享到 Line

分享到臉書