橋連結構 的英文怎麼說

中文拼音 [qiáoliánjiēgòu]
橋連結構 英文
bridged structure
  • 橋 : 名詞1. （橋梁） bridge 2. （姓氏） a surname
  • 連 : Ⅰ動詞1 （連接） link; join; connect 2 （連累） involve （in trouble）; implicate 3 [方言] （縫） ...
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 結構 : 1 （各組成部分的搭配形式） structure; composition; construction; formation; constitution; fabric;...
  1. Those of multi - span, middle - length ( about 25 - 40 metres ) are of large percentage among advanced bridges. simply - supported girder bridges with continuous decks are inferior to those of continuous girders because their decks crack easily. owing to the complex construction of continuous girder bridges, which is laboursome and time - consuming, people have been thinking about an approach to combining the advantages of the two so as to speed up the building and reduce the work procedures

    在高等級公路橋梁中，多孔中等跨徑（跨徑在25 40米左右）的橋梁占很大的比重，橋面連續的簡支梁結構體系由於存在橋面容易開裂等缺點而在與連續梁結構體系的競爭中常常處于下風。
  2. This paper presents the structural design of the main bridge of lhasa river bridge, makes a deep - going study of the key techniques for design of the bridge, such as the reasonable span length ratio of each span of the 5 - span girder and arch hybrid structure, mechanical behaviour of the dual arch ribs, and section of the continuous girder tie beam, and also works out rigidity and stress conditions of the continuous girder tie beam and stress conditions of the concrete - filled steel tube arches of the main bridge

    摘要介紹了拉薩河特大橋主橋結構設計情況，對於五跨梁拱組合橋梁各孔跨合理的跨度比、疊拱的受力行為及連續梁系桿截面形式等設計中的關鍵性問題進行了深入的研究，給出了主橋連續梁系桿的剛度和應力情況、鋼管混凝土拱的應力情況。
  3. Spatial analysis on continuous plate - truss compositesteel truss bridge across the wuhu changjiang river

    蕪湖長江大橋連續板桁結合梁的空間結構分析
  4. Abstract : the system, in the span - by - span construction of brid ge, willexperience three kinds of shifts from the state of simple beam to the continuous state, from overhanging beam to the continuous beam and from few - spans continuous beam to required degree span by span. meanwhile, structural calculatin g graphics and the internal force are changing with the three shifts

    文摘:在橋梁工程逐孔施工過程中，體系將發生由簡支梁狀態到連續梁狀態，由懸臂梁到連續梁，由少跨連續梁逐孔延伸到所要求的體系三種轉換，同時結構計算圖式和內力也發生變化。
  5. The structure of simply supported - continuous system is now common used in small span bridges and bridge approach of large span

    簡支轉預應力連續的施工方法是中、小跨徑橋梁和大跨度橋梁的引橋中普遍採用的結構型式。
  6. In order to meet the demand of bridgework, we monitor and analyze the stress and the deflection during the process of bridge construction

    本論文根據橋梁工程建設的需要，對施工過程中簡支轉預應力連續結構的應力和撓度進行理論分析和施工監測。
  7. 3 ) the influences on the internal forces by some variable parameters such as the ratio of the rise to span and the stiffness ratio are compared. the optimal range of these parameters is pointed out and some advances are also given

    研究探討了矢跨比、拱梁剛度比等參數對預應力混凝土連續梁拱組合體系橋梁結構內力的影響，並得出合理的取值范圍，為設計人員選取結構參數提供參考。
  8. The prestressed continuous beam - arch composite bridges are a special structural system where the horizontal thrust of the arch rib is absorbed by a prestressed tie at deck level. in some cases, this type of structure is preferable because it does n ' t have the large thrust at the spring hi traditional arch bridges and the somewhat large bending moment and shear force in traditional beam bridges. as a result, the performances of the prestressing reinforcement can be efficiently utilized

    它利用拱肋承擔壓力，系梁預應力束抵抗拱端推力，吊桿及縱橫橋面系結構承受橋面荷載，既克服了傳統拱橋巨大的拱端推力，又改善了連續梁橋較大的彎矩和剪力的受力狀況，最大限度地發揮了拱梁混凝土和預應力鋼筋各自的特點，經濟效益顯著。
  9. When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved

    分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。
  10. Generally, the skew bridge ' s calculation theories can be divided into three types : the category 1 is the plank theories method, such as the finite difference method, the finite element method and the finite strip method, etc ; the category 2 is the beam theories, such as the grid beam theories, the general grid theories, the rigid cross - beam method, the elastically - supported continuous beam method and the bar system analytical method, etc ; the category 3 is the practical method, such as the g - m revising method, the grid - beam simple method and ghali form coefficient method, etc

    目前關于斜梁橋的計算理論和方法概括起來，大致可以分為三類：第一類為板理論方法，如有限差分法、變分法、有限單元法、有限條法等；第二類為梁理論法，如格構梁理論、一般格構理論、剛性橫梁法、彈性支承連續法、桿件結構的分析方法；第三類為實用計演算法，荷載橫向分佈的計算方法如g ? m修正法、格構梁的簡易法、 ghali表格系數法等。
  11. Abstract : the paper presents the evaluation procedures and the major tests carried out on gangwan bridge in dalian port, illustrating the scope and methods of tests necessary for the evaluation and assessment of the strength and useful life of an aged steel bridge

    文摘:通過介紹大連港港灣橋的檢定試驗過程與主要項目內容，說明對老齡鋼結構橋梁的強度負荷與壽命評估所必須實施的內容與手段。
  12. From the view point of the whole topologies of current mode hfl inverters, two topologies of half - bridge and push - pull current mode hfl inverters are proposed, which are composed of four power switches. hfl inverters in discontinuous current mode ( dcm ) are extended to those in continuous current mode ( ccm )

    從完善電路拓撲和降低成本的角度出發，本文提出了兩種結構的電流源高頻鏈逆變電路，它們分別是由四個功率管組成的半橋和推挽雙向電流源高頻鏈單級逆變電路，並將工作在電感電流斷續模式的逆變電路擴展到電感電流連續模式。
  13. So the application of partial shear connectors in the building and bridge structure to supporting the fatigue load is feasible, and will bring considerable economic benefits

    因此必要的情況下在建築結構和橋梁結構中採用部分剪力連接來承受疲勞荷載的作用是可行的，並可帶來良好的經濟效益。
  14. In this paper, the three level fortification criterion, two stage design method and the elastic response spectrum theory are adopted, and the program of nba ( the program of nonlinear - aseismic analysis for beam bridge ) is used to calculate. through gathering, analyzing and calculating a lot of bridge design materials, this paper induces a simple way to calculate the relative displacement of the beam and the pier, and then according to the current design method, it concludes a better design principle of the supporting length of the beams. at the same time the dynamics is adopted to put forward the design method of the carrying capacity and the lengthen of prestress wire ( steel bar ) falling - off prevention structures of highway bridges

    本論文採用三水準設防、兩階段設計方法、彈性反應譜計算理論，運用橋梁結構非線性地震響應分析程序nba （ theprogramofnonlinear ? aseismicanalysisforbeambridge ）進行計算；通過收集大量的實橋設計資料，經分析計算，歸納總結出計算上下部結構相對位移的簡便計算方法；並綜合國內外的經驗值，提出梁的支承長度se的設計原則；同時運用動力學突加荷載的原理，推導分析了預應力鋼絞線式（鋼棒連接式）落梁防止裝置設計承載力的計算方法和設計伸長量s _ f的取值；最後本文通過實橋計算，說明了落梁防止系統設計的方法。
  15. The steel structure design of the connecting building and the connecting bridge of guangzhou new baiyun international airport

    廣州新白雲國際機場連接樓及連接橋鋼結構設計
  16. In order to ascertain the real stress and deflection of structure this paper puts forward experimental scheme. by measuring data during the process of construction, we can know the distribution of stress in simply supported - continuous beam and compare with initial design, then we can adjust it by control method to ensure quality of the bridge

    提出具體的試驗方案，論述了測試元件的測試原理，通過測量各控制點在不同階段的應變和撓度，確定橋梁結構的實際應力大小和變形狀態，了解簡支轉預應力連續結構各跨主梁與連續處的應力分佈情況，並與設計相互驗證，通過施工控制使結構符合設計要求，保證施工質量。
  17. Using theory of structure intensity and prestressed concrete bridge, this paper reviews theoretical computing method of stress and deflection. making use of the procedure of computing bridge structure, the structure of simply supported - continuous system is calculated and the result is analyzed, the character on force and deflection is generalized in the paper

    運用力學理論、混凝土結構強度理論和橋梁結構相關理論論述了橋梁應力與變形的理論計算方法；利用專用橋梁結構計算程序結合具體工程項目中的簡支轉預應力連續結構進行了數值模擬計算，並對計算結果進行理論分析，提出這種結構型式在受力狀態與結構變形上的特點。
  18. Especially the bridge engineering has to be concerned with high, new and difficult technologies. new technologies firstly adopted are post - tensioned prestressed concrete simply - supported box girder, assembly two - way prestressed concrete simply - supported t - girder, reinforced concrete continuous rigid frame, and steel - concrete composite continuous girder. all these have formed a series of new bridge structures taking prestressed concrete simply - supported box girder as main feature

    由於秦沈客運專線的特殊技術要求，在鐵路建設史上首次採用了后張法預應力混凝土箱形簡支梁、裝配式雙向預應力混凝土t形簡支梁、鋼筋混凝土剛構連續梁、鋼與混凝土結合連續梁等橋跨結構，形成了以預應力簡支箱梁橋跨結構為主要特徵的一系列橋梁新結構。
  19. Abstract : in this paper, a new simple method is put forward to on - line survey and analyse the real - time response of bridges loaded under random vehicles and people. based on linear elastic hypothesis and finite element method, the dynamic whole displacement state and load of the bridge can be obtained through surveying partial displacements, so the problem that load is unknown and difficult to determine when calculating is solved in a sense. this method is adap ted to girder bridge, arch bridge, cable - stayed bridge and suspension bridge. through the instrumentality of ways and means in this treatise, a real - time system to survey and analyse a working bridge can be established

    文摘:在線彈性假設基礎上，根據有限元理論和橋梁隨機車輛（行人）荷載的特點，討論並提出了一種通過監測部分位移，計算橋梁其餘位移和橋面荷載的簡化分析方法，解決了橋梁在隨機車輛（行人）荷載作用下的荷載確定問題，建立了動位移和等效節點荷載的有限元列式.該方法為橋梁結構的在線監測和實時分析提供了理論基礎，適用於連續梁橋、拱橋、斜拉橋和懸索橋等橋梁結構形式，具有實際應用價值
  20. At first, the soft of bridge structure, gqjs, is used to calculate the structure of prestressed concrete continuous beam bridge and the deformation and stress of the concrete box beam are given out ; then by measuring and analyzing the datum of the stress in the prestressed steel rope and the stress of section in the concrete box beam, this article presents two ways to identify the reasonable friction deviation factor k between longitudinal prestressed tendons and the wall of duct ( indirectly and directly ), and discover the regular pattern of prestressed friction loss

    首先運用橋梁結構分析專用軟體gqjs對預應力混凝土連續梁橋進行結構計算，得到了各施工工況下混凝土箱梁的撓度和截面應力；然後給出了識別引起結構預應力損失的孔道偏差系數k的兩種方法（間接法和直接法） 。通過對測得的預應力索沿程應力和混凝土箱梁截面應力數據的分析處理，得到了合理的預應力孔道摩擦偏差系數及預應力摩阻損失規律。
分享友人
分享到 Line

分享到臉書