殘余破裂 的英文怎麼說

中文拼音 [cányúpòliè]
殘余破裂 英文
residual fracture
  • 殘 : Ⅰ形容詞1 （不完整; 殘缺） incomplete; deficient 2 （剩餘的; 將盡的） remnant; remaining 3 （兇惡...
  • 余 : Ⅰ動詞（剩下） remain; leave: 9減4 余 5。 nine minus four is five ; four from nine leaves five ; i...
  • 破 : Ⅰ動詞1 （完整的東西受到損傷） be broken; be damaged 2 （使損壞） break; break down; damage 3 （使...
  • 裂 : 裂動詞[方言] （東西的兩部分向兩旁分開） open
  • 破裂 : break; fracture; burst; split; rupture; crack
  1. Upon cooling, the thermal mismatch between residual silicon and quartz usually results in the fracture of the crucible.

    當冷卻時，殘余的硅和石英間的熱失配往往導致坩堝破裂。
  2. Specifically, according to the w - w five parameters failure theory, the fracture criterion of crack is established, and the state of crack ( open or close ) is judged by the values of the crack strain. combining the two points, the predict - model about the failure of concrete material is established. this predict - model can predict 16 failure forms, and basing the different failure form predicted after crack, the stress - strain relationship matrix of concrete material is adjusted

    具體來講，根據w - w的五參數混凝土破壞理論，建立混凝土的開裂準則，根據開裂應變值來判斷裂縫是張開還是閉合，從而在兩者基礎上建立了裂縫的開裂預測模式，總共有16種開裂模式；裂后根據具體的開裂模式及殘余抗剪能力來調整混凝土的本構關系矩陣，即用等效剛度代替原有剛度，考慮到垂直於裂縫方向的剛度為零，這樣會使裂后的總剛出現病態，為此文中通過引用鬆弛系數來對出現裂縫的單元進行預處理，一方面可解決因過大的舍入誤差導致計算結果的不可信問題，另一方面就是可加速收斂。
  3. Thermal and welding residual stress often produces in the proceeding of the electronic package, the residual stress release and thermal deformations of the microelectronics will reduce the assemble intensity between the chip and package, and then debase the electrical performance of the assemble circuit, numerous thermal cycling will lead to thermal fatigue or thermal failure of the microelectronics

    電子封裝器件在生產的工藝過程中，往往會產生熱殘余應力以及焊接殘余應力，殘余應力的釋放作用及器件在使用過程中的熱變形，會降低集成電路晶元與封裝體的結合強度，進而降低集成電路的電性能，反復的熱循環，將導致器件的熱疲勞失效，嚴重時可導致矽片或陶瓷片破裂，使整個器件遭到破壞。
  4. The critical crack and stress put forward provides theoretic foundation for monitoring portal machine. 3. applying steady theory of board, studying the problem of early curvature, flexibility model, welding remaining stress, elastic transmutation and brace condition and so on, conclude that structure of beam is primary place where metal structure of portal crane lose stabilization and the break of main beam is result of losing partial stabilization of main board

    文章提出的界限應力和臨界裂紋對于港口機械的監測提供了理論依據； 3 、運用板的穩定理論，探索了作為薄壁構件的門機金屬結構在失穩破壞中所涉及到的初曲率問題、彈性模量問題、焊接殘余應力問題、彈塑性變形問題以及支承條件問題等，得出了門機金屬結構發生失穩破壞的主要部位為臂架結構，且主臂架的折斷是由於受壓翼板局部失穩引起整體破壞； 4 、探討了焊接對結構承載的影響。
  5. In this dissertation, the research trends for the problem have been introduced ; the ‘ dim ’ and ‘ point ’ has been strictly defined in mathematics from machine vision and human vision ; the ideal clutter suppression system based on clutter predication and the realization and evaluation of evaluation index has been studied, in succession the clutter suppression technologies have been researched. firstly, the classic nonparametric algorithm has been analyzed in detail and systematically, for it ’ s weakness that it cannot remove the non - stationary clutter ideally, kalman filter algorithm for clutter suppression in 2d image signal has been built. secondly, fast adaptive kalman filter is presented based on fast wide - sense stationary areas partition algorithm : limited combination and division algorithm based on quarti - tree algorithm, new taxis filter route algorithm which can break through the limitation of the necessity of pixel neighborhood of 2d filter and laplace data model with two parameters which is perfectly suitable for the residual image of kalman clutter suppression

    首先分析了經典的非參數法，對於四種具有代表性的核，從前述的三個性能評價方面做了分析和對比，指出了其速度快的優點和對非平穩圖像適應性差的弱點，針對非參數法的弱點，重點研究了對非平穩圖像適應良好的卡爾曼雜波抑制技術:建立了非平穩圖像的類自回歸模型，在此基礎上建立了二維卡爾曼濾波基礎的兩個方程:狀態方程和測量方程;建立了非平穩圖像準平穩區域快速劃分演算法:基於四叉樹法的有限分裂合併演算法;二維空間的基於k排序的濾波路線演算法，突破了空域濾波路線上區域相鄰的限制;在這些研究的基礎上實現了快速卡爾曼估計，實驗驗證了該方法相對逐點卡爾曼估計可以提高運算速度三倍左右;雜波抑制結果表明傳統的高斯性檢驗並不適合卡爾曼估計后的殘余圖像，由此建立了殘余圖像的雙參數拉普拉斯模型，實驗表明其可以完好的吻合殘余圖像的概率密度曲線。
分享友人
分享到 Line

分享到臉書