殘碳試驗 的英文怎麼說
中文拼音 [cántànshìyàn]
殘碳試驗
英文
carbon tesidue test-
Standard test method for conradson carbon residue of petroleum products
石油產品康拉孫殘碳的標準試驗方法Standard test method for insoluble residue in carbonate aggregates
碳酸鹽集料中不溶性殘渣的標準試驗方法This segregation behavior of sn accords with the mechanism of non - equilibrium segregation. it can be obtained through the theoretical calculations that the critical time of sn non - equilibrium segregation is 124 seconds at 750 and the critical cooling rate is 8 / s when cooling from 1320. it is suggested that controlling the cooling rate during continuous casting to avoid the critical cooling rate ( 8 / s ) and avoiding high stress near the trough temperature ( 750 ) may control the form
通過研究殘留元素sn的偏聚機制及其對o . 15wt . % c鋼熱塑性的影響，對試驗鋼進行脆性預測:建議在該鋼的連鑄過程中彎道矯直溫度盡量避開塑性谷底溫度750 ，二冷區的冷速盡量避開臨界冷卻速率8 / s ，從而可以減少該低碳鋼連鑄坯表面裂紋和橫向裂紋，提高其成材率。The results show that, with the quenching temperature ( 270 ~ 380 ) increasing, the carbon content and percentage content of retained austenite increase first and then decrease, which are up to a maximum value at 360 ; the tensile strength of adi decreases ; the elongation and impact ductility of adi increase first and then decrease, which are up to a maximum value at 360 ; but the hardness of adi decreases first and then increases, which is up to a minimum value at 360
結果表明，在試驗溫度范圍內（ 270 ~ 380 ） ，試樣中殘余奧氏體的含碳量及其含量隨著等溫淬火溫度的升高先增大后減小，均在360等溫淬火時出現最大值；抗拉強度隨著等溫淬火溫度的升高而逐漸降低；伸長率和沖擊韌度隨著等溫淬火溫度的升高先增大后減小，在360等溫淬火時出現最大值；硬度則隨著等溫淬火溫度的升高先減小后增大，當360溫淬火時硬度最低。Standard test methods for residual carbon, apparent residual carbon, and apparent carbon yield in coked carbon - containing brick and shapes
含焦化硬瀝青磚及異型磚的殘余碳表觀殘余碳及表觀出碳量的標準試驗方法Test methods for determination of trace elements in coal, coke, combustion residues from coal utilization processes by inductively coupled plasma atomic emission, inductively coupled plasma mass, graphite furnace atomic absorption spect
用感應耦合等離子體原子發射光譜法感應耦合等離子體質譜法和石墨爐原子吸收光譜法測定煤焦碳和煤利用過程中產生的燃燒殘余物中痕量元素的試驗方法Standard test method for determination of residual contamination of materials and components by total carbon analysis using a high - temperature combustion analyzer
用高溫氧化分析儀全碳分析法測定材料和元件中殘余雜質的標準試驗方法分享友人