比例針閥 的英文怎麼說

中文拼音 [bǐlìzhēnfá]
比例針閥 英文
proportional action needle valve
  • 比 : Ⅰ動詞1 （比較; 較量高下、 長短、距離、好壞等） compare; compete; contrast; match; emulate 2 （比...
  • 針 : Ⅰ名詞1 （縫衣物用的工具） needle 2 （細長像針的東西） needle like things 3 （針劑） injection; sh...
  • 閥 : 名詞1 （指在某方面有支配勢力的人物或家族） established house or power group; a powerful person or...
  • 比例 : 1. （長度上縮小和放大的倍數） scale; scaling 2. （比率） proportion; ratio; proportionality
  1. Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc

    本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。
  2. Based on advanced technology, this thesis bring forward the optimal scheme and set down general system - drawings and flow charts. using step7 - micro software, we achieve the auto - control aim in drinking water treatment. in practice, the complexity and non - linaerity exit in the system of water treatment, so we apply fuzzy control in water treatment and design a kind of controller which structure can be altered according to the using - rate of ozone and the variety of water quality

    實際飲用水處理系統由於存在復雜性、非線性、時變性，本文根據臭氧生物活性炭水處理工藝存在復雜性、非線性、時變性等特點，將模糊控制應用在水處理這一不確定的非線性時變系統，針對不同水溫下臭氧利用率及水質的變化，設計一種基於系統過程狀態的變結構的模糊控制器，以單片機作為主要控制硬體，按查表方式設計軟體，對進水閥門開度進行在線控制，調節臭氧氣體與進水的比例（臭氧流量及濃度不變） ，達到氣水比最優化。
  3. Aiming at the disadvantages of present loading system applying proportional relief valve or servo valve, loading system with 3 - way proportional pressure reducing valve is proposed

    針對目前採用比例溢流閥和伺服閥加載存在的不足，提出在鋼坯修磨機上採用比例三通減壓閥加載。
  4. Research status and performance of pneumatic ratio servovalve are deeply analyzed. they provide theoretical base for high accuracy orientation control of servo control system and pointers for improving system performance. additionally

    對氣動比例伺服閥的特性與研究狀況進行了較為深入的研究，為伺服控制系統的高精度的定位控制提供了理論基礎，改善系統性能提供了指針。
  5. This paper establishes the mathematic model which expresses the dynamic characteristic of the water hydraulic proportional valve, and performs emulation study on time - domain and frequency - domain dynamic characteristic of the valve using matlab

    針對設計的水壓比例節流閥，建立了動態特性的數學模型，並利用matlab軟體對水壓比例節流閥的時域動態特性和頻域動態特性進行了模擬研究。
  6. This paper analyses the type, function and characteristics of usual proportional control valves and raises a new modificative version in the light of their drawback. that is, basing on the principle of flow amplification and electrical feedback and throughout calculation and analysis on flow closed loop control and pressure flow combination., determination of the minimum controlled pressure difference as well as flow controlling range and structure of main valve and research of the dynamic and static characteristic, the paper puts forward control principle of " flow - load pressure change - displacement revision " and pressure / flow double closed loop, and further expounds that using a proportional controller and a electric mechanical transducer can separately serve the control function of pressure or flow as well as flow pressure combination

    本論文分析了目前常用比例閥的類型、功能、特性，並針對其不足提出新的改進方案，即：以流量放大，電反饋兩個原理為基礎，通過對流量閉環控制及壓力流量復合的計算分析、確定上最小控制壓差及流量控制范圍，確定主閥結構、功能特性研究等，提出了「流量? ?負載壓力變化? ?位移修正」的控制原理和壓力流量雙閉環控制原理，並進一步論述了利用一個比例控制器和一個「電?機械轉換器」就可完成獨立的壓力或流量控制功能以及流量壓力復合控制功能。
  7. In order to solve the problems that large energy consumption, temperature variation, high, cost trouble maintenance in current electro - hydraulic servo control system for material testing machine, a new design scheme that electro - hydraulic proportional control system for material testing machine based on extension control strategy is proposed. the design scheme is successful by means of designing new main frame system, hydraulic cylinder system, digital electro - hydraulic micro - fluid proportional valve and electrical control system, and its results lay a foundation for material testing machine industries in our country

    針對國內外材料試驗機主要採用電液伺服控制系統，存在能耗大、溫升、成本高、維護困難等問題，本課題提出了基於可拓控制策略的材料試驗機電比例負載適應控制系統這一新型研究方案，通過開發新型試驗機主機系統、液壓缸系統、數字式微小流量電液比例流量閥及電控系統，實現了材料試驗機電液比例負載適應控制，為我國材料試驗機自動控制系統的產業化打下了基礎。
  8. The objective of this dissertation is a kind of press - high speed numeric control oil - press. with a theoretical analysis and study about proportional control system, this paper sets up the mathematical model of proportional valve controlled non - symmetry hydraulic cylinder via the hydraulic system model building. then analyzes and modifies the model based on the matter of this study, and simulates the model with matlab software to confirm pid parameters, thus designs the pid controller

    本學位論文針對一具體的研究項目?高速數控壓機的開發，對比例控制系統進行理論分析與研究，通過對液壓系統的精確建模，建立起比例閥控非對稱液壓缸的數學模型，然後根據所研究問題的實際情況對模型進行必要的分析和修正，再運用模擬軟體matlab分析系統模型及確定pid控制參數，設計出pid控制器，使得控制系統的設計具有更多的可靠性和靈活性，最後運用pic單片機實現此控制，並結合整機調試試驗驗證了pid控制的成功。
分享友人
分享到 Line

分享到臉書