比熱容 的英文怎麼說

中文拼音 [bǐrèróng]
比熱容 英文
capacity, specific heat
  • 比 : Ⅰ動詞1 （比較; 較量高下、 長短、距離、好壞等） compare; compete; contrast; match; emulate 2 （比...
  1. Also the theoretical basis of the method have been checked through simple deducing simulation and the influences of various physical parameters on the method have been studied. it is shown that the method is theoretically reliable for the production oil wells without very high production rate and is more suitable in field production for oil wells ( i ) in area with bigger geothermal gradient ; ( ii ) producing fluids ( oil and water ) with distinguish thermal characteristics ; ( iii ) producing oil with lower heat capacity or water with higher heat capacity ; ( iv ) with good surface measurement accuracy, as well as the method h as certain requirements on the accuracy of the temperature and flowmeter logs sensors

    就該產出剖面方法的理論基礎進行了簡單的正演模擬和可能影響該方法的各項物理參數進行了全面的考察，結果表明，該方法對于非高產的生產油井來說在理論上是可靠的，在實際生產中適合於（ 1 ） 、油井所在地區地溫梯度較大的油井； （ 2 ） 、油水熱特性差別較大的油井； （ 3 ） 、油比熱容值偏低水比熱容值偏高的油井； （ 4 ） 、井口計量精度較高的油井，並且對井溫測井和流量測井的傳感性精度有一定的要求。
  2. Testing methods for specific heat capacity of plastics

    塑料比熱容的測試方法
  3. Specific heat capacity at constant pressure

    定壓比熱容量
  4. What is the specific heat of the metal in the pan ?

    這只鍋的金屬的比熱容是多少？
  5. Specific heat depends not only on the material in question but also on the external conditions of its heating.

    比熱容不僅取決于所研究的物質，而且依賴于加熱的外部條件。
  6. The specific heat of a material is the amount of heat that must be added to a unit mass of the material to raise its temperature by 1 degree.

    物質的比熱容是使單位質量的物質溫度升高1度所須加給的熱量。
  7. 05. 02 test method for specific heat of liquids and solids

    測定液體和固體比熱容的試驗方法
  8. Specific heat capacity at constant volume

    定容比熱容量
  9. Test methods of thermal diffusivity, specific heat capacity, and thermal conductivity for fine ceramics by laser flash method

    激光閃爍法測定精細陶瓷的熱擴散率比熱容量熱傳導率試驗方法
  10. With high temperature and high pressure in nozzle of wind tunnel, the effect of variable specific heat on nozzle design must be considered

    本文針對超音速、高超音速噴管內馬赫數、溫度變化劇烈的特點，研究了比熱容變化對設計噴管型面產生的影響。
  11. The principles and its system error analysis of measuring specific heat ratio of the air

    空氣比熱容比實驗的原理和系統誤差分析
  12. Standard test method for determining specific heat capacity by differential scanning calorimetry

    用差示掃描熱量測定儀測定比熱容量的標準試驗方法
  13. Specific heats of various inorganic materials

    各種無機材料的比熱容
  14. Test method for mean specific heat

    纖維增強塑料平均比熱容試驗方法
  15. Specific heats of the various phases of water

    各種相態水的比熱容
  16. Test method for mean specific heat capacity of fiber reinforced plastics

    纖維增強塑料平均比熱容試驗方法
  17. Specific heats of organic compounds

    有機化合物的比熱容
  18. To prove the accuracy of the mach number, and the parameter homogeneity of the design nozzle " s exit, cfd calculate has carried on the design results. under the condition of supersonic and hypersonic flow, and a certain range of temperature, and mach number, the conclusion of the influence of specific heat to nozzle design is drawn

    為了驗證所設計的噴管出口馬赫數的大小和噴管出口流場的均勻性，採用nnd格式和b l湍流模型求解雷諾平均n - s方程，對設計結果進行了cfd驗算，得出了在一定溫度范圍內，超音速、高超聲速流動的條件下，不同馬赫數范圍內變比熱容對噴管型面和噴管出口馬赫數的影響。
  19. Advanced technical ceramics - monolithic ceramics - thermo - physical properties - determination of specific heat capacity

    高級工業陶瓷.整體陶瓷.熱物理特性.比熱容的測定
  20. Ln chapter 4, imbalanced counterflow of indirect evaporative cooling is simulated while taking into account the non - linearity of the saturation line of moist air. four diagrams are provided to assist in determination of the optimum heat capacity ratio

    第四章針對蒸發冷卻過程中飽和濕空氣比熱容隨溫度的非線性變化關系，研究了非平衡流逆流間接蒸發冷卻過程（火用）損失及最佳熱容量比的計算線圖。
分享友人
分享到 Line

分享到臉書