氣焊熱 的英文怎麼說

中文拼音 [qìhànrè]
氣焊熱 英文
gas-welding heat
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  1. " blowtorch : a portable burner for mixing gas and oxygen to produce a very hot flame, used for soldering, welding, and glass blowing.

    噴燈:使混合氣體和氧氣產生更熾熱火焰的便攜助燃劑，常用於接合、焊接和玻璃吹制。
  2. Phenolic foam is a new generation heat preservation prevent fire soundproof material and polystyrene together ammonia ester foaming rubber etc, material to compare, and it is good that its biggest characteristics is a heat - proofound the low temperature contractility is smatt, and have te special prevent burning wit the size stability under 2000 heat, not burning, not melt not contract constant form not poisonous spirit hove no thick smoke, just surface formation layer

    信息內容：酚醛泡沫為新一代保溫防火隔音材料與聚苯乙烯聚氨脂發泡橡膠比，其最大特點是耐熱性好，低溫收縮性小，具有獨特的阻燃和尺寸穩定性，在焊槍火焰下，不燃燒不收縮不變形，無毒氣無濃煙，只是表面炭化，性質穩定，耐化學腐蝕抗老化。
  3. ( 2 ) design of the implantating device : some quantity of 316l stainless steel, perform forging and thermal rolling, drawing filament ( diameter 0. 4mm and 0. 23mm respectively ), enlacing and jointing, after that assembling the products into guiding filum, a technical examination was carried out to appraise their physical capability. the second part : experimental study : animal experiments were used to screen and observe its validity and security : under general anesthesia, tracheotomy was performed on the healthy dog, the bronchus was localized using x - ray fluoroscopy fibrobronchoscope and with the help of the implanting equipment, several niti alloy occludes were implanted into the target bronchus of the dogs through the biopsy channel in the fibrobronchoscope

    （ 2 ）推送器的研製：取316l不銹鋼熱軋，分別拉製成不同直徑的不銹鋼絲分別用作製作內芯、外環及車制螺絲，再經纏繞、焊接、裝配成推送器。對上述兩者進行技術鑒定。第二部分：支氣管封堵器的實驗研究：四種形狀的封堵器分四組（上述四種封堵器各12隻）進行動物實驗，分別觀察其安全性與有效性。
  4. Welding of thermoplastics - machines and equipment for hot gas welding including extrusion welding

    熱塑焊接.熱氣焊機械和設備
  5. Welding of thermoplastics - machines and equipment for hot gas welding including extrusion welding ; german version en 13705 : 2004

    熱塑性材料焊接.熱氣焊機械和設備
  6. Mag welding for 12ni14 low temperature steel heat exchanger

    14低溫鋼換熱器的混合氣體保護焊
  7. With an introduction of the influences of the final quality of rail aluminothermic welding, such as : the quality of welding kits ( esp. the portion ), the result of pre - heating, the welding operation and the level of operators etc., this paper analyzes some problems when rail welding under special conditions

    摘要介紹了焊接材料質量、預熱效果、操作人員水平等因素對鋼軌鋁熱焊接接頭質量的影響，以及幾何誤差不同、軌頭寬度不等、寒冷氣候等特殊條件下進行鋁熱焊接應注意的問題。
  8. Usages : exhaust pipes of aircraft, boiler covers, heat exchangers, boiler pipes, some parts that are impossible for heat treatment after welding or assembling

    航空器排氣管、鍋爐蓋罩、熱交換機、鍋爐用管、延展接頭等的焊接、接合后無法熱處理的零部件及設備。
  9. After a nationwide restructuring of colleges and departments in 1952, the department was renamed as the department of machine manufacturing, comprising 5 disciplines manufacturing technology, foundry technology and equipment, forging and pressing technology end equipment, welding technology and equipment, and etall. graphy and heat treatmento in addition, on the basis of the original power machinery teaching group, the department of power machinery was set up, having 3 disciplines : thermal electr

    1952年院系調整，更名為機械製造系，設機械製造工藝鑄造工藝及設備壓力加工工藝及設備焊接工藝及設備金相熱處理5個專業，並且由原動力組擴建成立了動力機械繫，正式設有熱力發電后改為鍋爐燃氣輪機汽車拖拉機3個專業。
  10. Gas welding equipment - thermoplastic hoses for welding and allied processes ; german version en 1327 : 1996

    氣焊機.焊接及相關工藝用熱塑軟管
  11. Results show that the brittle fracture is mainly caused by hydrogen brittleness that results from the oxidation arid absorbing hydrogen of copper tube during braze welding

    同時在加熱和冷卻時，由於異種材料的熱脹系數差別過大，產生的較大熱應力作用於已存在的裂紋，促使裂紋二次擴展，甚至使得晶粒脫落產生空洞，最終導致焊接接頭漏氣失效。
  12. Hot - rolled atmospheric corrosion resisting steels for welded structure

    焊接結構用耐大氣腐蝕熱軋鋼材
  13. On the basis of the experiment, the reason that high strength 7a52 aluminum alloy produced the familiar defects such as hot cracking, porosity, slag patch, etc. in the welding was analyzed, and the preventive measures of every defect were adopted

    摘要在實驗的基礎上分析了高強7a52鋁合金焊接時出現的常見焊接缺陷：熱裂紋、氣孔、夾渣等產生的原因，並對每種缺陷提出了預防措施。
  14. Our main products are plate heat exchanger, unit heat exchanger, spiral heat exchanger, displacement heat exchanger, air radiator, welded plate heat exchanger, shell and tube heat exchanger, heat exchange boiler, etc

    公司主要產品有板式換熱器、換熱機組、螺旋板式換熱器、容積式換熱器、空氣散熱器、釬焊板式換熱器、全焊板式換熱器、列管式換熱器、全自動換熱開水器等設備。
  15. Semiconductor devices - mechanical and climatic test methods - part 20 : resistance of plastic - encapsulated smds to the combined effect of moisture and soldering heat

    半導體裝置.機械和氣候試驗方法.第20部分:塑料密封的smds抗濕氣和釬焊熱綜合影響的性能
  16. About design programs of propylene tower post weld whole heat treatment, we have made analyses and compare from the various technical and economic aspects, and in vertical state of large pressurized vessel, we propose to adopt the internal combustion heat treatment method, in horizontal state of it, to adopt high temperature flue gas heat treatment method, and propose center combustion tube method as the future direction of technical developmnet insights

    摘要圍繞丙烯塔焊后整體熱處理的各種設計方案，從技術、經濟等方面進行分析對比，提出對超大型壓力容器，立置狀態下宜採用內燃法熱處理；臥置狀態時宜採用高溫煙氣法熱處理，並提出將中心燃燒管法作為今後技術發展方向的見解。
  17. Semiconductor devices - mechanical and climatic test methods - resistance of plastic - encapsulated smds to the combined effect of moisture and soldering heat

    半導體器件.機械和氣候試驗方法.塑料包封的smds的抗濕及釬焊熱度綜合影響
  18. Gas welding equipment - thermoplastic hoses for welding and allied processes

    氣焊設備.焊接和類似工藝用熱固性軟管
  19. Gas welding equipment. thermoplastic hoses for welding and allied processes

    氣焊設備.焊接和相關工藝用熱塑性塑料軟管
  20. Steam heating : adopting total copper tube bending method without welding, so it ' s stronger and can extend the heater ' s life

    蒸氣加熱，採用整支銅管彎曲成型未經焊燒保持銅管耐久不破，使加熱器壽命延長。
分享友人
分享到 Line

分享到臉書