沖緣加工 的英文怎麼說
中文拼音 [chōngyuánjiāgōng]
沖緣加工
英文
burring-
Highest insulation resistance and low dielectric loss under severe humidity conditions, for use in electronic insulators, telecommunications apparatus and meters. it s also suitable for cold punching, carbon printed, and vr used
高度級電氣絕緣性，耐濕性特佳，製造電氣絕緣電子絕緣器通信及電表等配件，適于冷沖打拔加工碳膜印刷電板及vr使用電木板。Abstract : there are offered many ways how to improve work of a spark plug. but one of the m ost important problems has not been solved yet. this is a thermal mode operation of a spark plug. the ideal spark plug should be instantly heated at the moment of occurrence of a spark and instantly cooled down in expectation of the foll owing electrical pulse. thus it balances between preservation of heat for self ? c leaning from scale and its removal in avoidance self ? ignition. in this article a uthor managed for this time to offer a spark plug with capability “ self ? regula tion ” of heat flux removed from a zone of ignition. essence of the offer is a t ip ， which is transparent for heat flux. it is produced from single crystal of sap phire
文摘:在如何提高火花塞的工作質量方面有多種方法，但是其中最重要的一個問題還沒有得到解決，那就是火花塞工作的熱學模型問題.理想的火花塞應該能在點火的瞬間被立刻加熱，並且在接下來的電脈沖過程中迅速冷卻，由此在熱量的存儲與散發之間取得平衡，以避免自點火.本文力圖展示一種具有自動調節源於點火區域熱流能力的火花塞，其技術的關鍵是頂部絕緣體材料，它是由藍寶石單晶製作，而非傳統的氧化鋁陶瓷Ghg - electrical grade activated silica powder is produced by way of mingling on the basis of electrical grade silica powder. it has activt effect on surface & make silica powder mingled with resin, raise cohesive force between resin & silica powder, raise the water - resestance on the sunface and the compressive strength of pour object, reduce sediment, gradation & split, increase filler of silica powder, and replaced inpoted products on the producing line of imported dry type transfomer & high tension mutual induc tance equiment, it has been the best pouring insulate materual in electrical trade
電工級活性硅微粉是在電工級硅微粉的基礎上進行偶聯化處理而製成，具有表面活性作用，能使用硅微粉與樹脂發生交聯，提高樹脂與硅微粉的粘結力和界面增水性，提高澆注體抗沖擊強度，減少沉澱、分層、開裂現象，增加硅微粉的填充量，在引進的乾式變壓器、高壓互感器生產線上已成功地代替了進口產品，成為電工行業理想的環氧澆注絕緣材料。The influence of microstructure on the flashover performance of alumina ceramics has been studied systematically through investigating the flashover performance of different alumina ceramic samples. experimental results reveal that the flashover performance is affected by the grain sizes and its dispersiveness. the smaller grain size is, the higher flashover performance ; the less dispersiveness of grain sizes is, the higher flashover performance
3 .通過研究用不同工藝制備的氧化鋁陶瓷絕緣子（同一材料配方不同燒成工藝、同樣氧化鋁含量不同添加劑）在沖擊電壓作用下在真空中的沿面閃絡特性和表面帶電特性，首次深入系統地探索了材料微觀結構對陶瓷材料沿面閃絡性能的影響規律。Highest insulation, fire resistance and humidity resistance. it s suitable for use in tv parts, etc
絕緣特性，耐濕製造高級電視零件等，並且具有自熄特性，適于冷沖打拔加工。The main contributions to the study on the flashover of insulators in vacuum are as follows : 1. a set of test system for the studies on flashover of insulators in vacuum has been developed, which consists of vacuum system, electrode system, e - dot pulse voltage measurement system, surface charge measurement system, current monitor system and luminescence signal measurement system
本文主要完成了以下工作： 1 .通過設計加工真空及試驗電極系統，研製e - dot沖擊電壓測量系統、真空中表面電荷測量系統、沖擊電流和表面微弱光信號測量系統，建成了國內第一套用於研究真空中絕緣子沿面閃絡現象的試驗平臺。The solution formula of dwell time is deduced by using the pulse iteration method and the smoothing fourier transition method, and the formula can be simplified referring to workpiece shape. according to the anastomotic status of the tool and workpiece surface, we present the new model of the inherent relation among local pressure density, removal rate, convergence ratio and residual errors, and the corresponding formulas are given. the forming cause of the edge effect in the polishing process is analyzed, and the means which reduces the edge effect is put forward
2 、針對計算機控制光學表面成形（ ccos ）的加工方式、誤差收斂特點，研製了去除函數呈高斯分佈的雙轉子結構研拋模；採用脈沖迭代法、平滑因子傅立葉變換法推導出駐留時間的演算法，求解過程中根據工件面形的特點作了各種形式的簡化；提出了工件表面和研拋模的吻合誤差與局部壓強、材料去除率、收斂比之間內在關系的數學模型，並推導出相應的計算公式；分析了邊緣效應產生的原因，在加工過程中採用相對壓力因子對去除函數進行修正，可以消除邊緣效應的影響。分享友人