沸騰傳熱系數 的英文怎麼說

中文拼音 [fèiténgzhuànrèxìshǔ]
沸騰傳熱系數 英文
boiling heat transfer coefficient
  • 沸 : Ⅰ動詞（滾開） boil; bubbleⅡ形容詞（滾開的;沸騰） boiling; bubbling
  • 騰 : 騰象聲詞（形容猛然動作發出的聲音）
  • 傳 : 傳名詞1 （解釋經文的著作） commentaries on classics 2 （傳記） biography 3 （敘述歷史故事的作品）...
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 沸騰 : 1 [物理學] （液體氣化） boiling; ebullition; ebullience; elixation 2 （情緒高昂） seethe with exc...
  • 系數 : [數學] coefficient; ratio; modulus; quotient; factor
  1. Using the opened thermosiphon of 38x3 as experimental element and water as working fluid, the characteristics of dynamic low load boiling, stable severe boiling heat transfer coefficient and critical heat flux are gotten for the opened thermosiphon at the pressure of 0. 02 - 0. 1mpa and 0. 1 - 0. 8mpa respectively, which makes up the drawback that the opened thermisiphon has not yet accurate boiling heat transfer relationship formulas. by means of experimental results, an opened thermisiphon waste heat recovery boiler is designed for the high temperature gases that the positi e electrode copper refining furnace exhaust, which overcomes effectively the drawback of short life, little capacity and unable to inspect that the closed steel - water thermosion has

    本文以工程上常用的38 3的開口封底為實驗元件，以水為工質，對開啟式熱管內的動態低負荷沸騰、穩態旺盛沸騰及臨界沸騰特性進行系統的可視化實驗研究，實驗壓力為0 . 02 0 . 8mpa ，實驗得出了38 3的開口封底管在工作壓力為0 . 02 0 . 8mpa和0 . 1 0 . 8mpa下的管內沸騰傳熱系數及臨界熱負荷計算關聯式，彌補了開口封底管? ?這一新型傳熱元件尚無準確的沸騰換熱關聯式的缺陷。
  2. Boiling heat transfer coefficient

    沸騰傳熱系數
  3. It was shown that under the conditions of the present study, when x < 0. 4, nucleate boiling was dominant, whereas when x > 0. 4, the forced convective boiling was dominant

    分析了沸騰傳熱系數隨干度的變化關系，結果表明在本實驗工況下：當干度小於0 . 4時，起主導作用的傳熱機制為核態沸騰，而當干度大於0 . 4時，起主導作用的傳熱機制為強制對流沸騰。
  4. On the basis of heat transfer theory, this paper analyzes heat transfer process in film boiling stage when axial workpiece is quenched vertically and distribution of steam film thickness as well as corresponding variation of heat - transfer coefficient

    摘要以傳熱學理論為基礎，對軸類工件豎直淬火時膜沸騰階段的傳熱情況進行分析，分析了工件表面蒸汽膜厚度的分佈情況和傳熱系數的相應變化。
分享友人
分享到 Line

分享到臉書