法向壓應力 的英文怎麼說
中文拼音 [fǎxiàngyāyīnglì]
法向壓應力
英文
direct compressive stress-
Based on the close analysis of the influence factors of the vertical bearing capacity, circular aperture extension theory is employed to establish the computing formulas for the pile vertical stress and the foundation vertical bearing capacity, respectively. moreover, with analyzing the features of the calculation parameters such as materials of gunite mortar, jet pressure, diameter of the jet pipe, pile length, pile layout, a design theory for chemical churning pile composite foundation is proposed. then, the variation of the pipe deformation with loads, the deformation coordination of pile and soil are studied
在此基礎上深入探討了旋噴樁的樁土受力特性及其復合地基的加固機理，從影響旋噴樁復合地基豎向承載力的因素入手，基於圓孔擴張理論給出了樁體豎向應力及旋噴樁復合地基的豎向承載力計算公式;通過對噴射漿液、噴射壓力選取、噴射直徑估算、樁長及樁位設計等各種計算參數的深入分析和研究，提出了一套相應的旋噴樁復合地基設計計算方法;通過計算分析，深入探討了旋噴樁復合地基變形隨荷載變化規律、樁和樁間土變形協調關系、樁土應力比及復合地基壓縮模量的確定，並提出相應的設計方法和修正參數;此外，結合工程應用，對旋噴樁復合地基的施工技術及其現場質量檢測方法進行了較全面的探討。The dynamic tensile stresses of earthquake may balance or exceed to the precompression stresses due to static watef, this may arouse opening of joints along the normal direction. if the altemate actions of earthquake join, the joints may behave gradual opening and closing
由於地震作用時的動拉應力將抵消並超過靜載作用下的壓應力，導致橫縫面沿法向張開，加上地震的交變作用，橫縫可能會呈現反復的「漸開漸合」現象。This paper referred to the massive domestic and foreign technical material, elaborated in the sheet forming value simulation theory essential technology in detail, points out when analysis sheet forming question should use the big distortion ball plasticity fem and introduce the application characteristic and the function summarizes of the sheet forming simulation software dynaform. secondly, analyzed the cover forming characteristic, simultaneously introduced the influence cover forming factor in detail : such as ramming direction, the craft addendum surface and the material pressing surface, the radius of convex - concave mold, draw bead, pressure strength, blank size and craft margin and so on. and simulates many typical automobiles cover panel with software : such lateral board, back taillight pedestal and storage cover
其次，分析了覆蓋件成形的特點和要求，同時詳細介紹了影響覆蓋件成形的因素如沖壓方向、工藝補充面和壓料面、凸凹模圓角、拉延筋、壓邊力、坯料尺寸和工藝切口等，並用數值模擬軟體對多個典型的汽車覆蓋件汽車后側圍板、后燈座以及轎車后備箱蓋的沖壓成形情況進行模擬，用模擬結果優化拉延工藝方案，比較了內覆蓋件和外覆蓋件在成形特點和要求的一些異同點，以及常見的起皺、拉裂和回彈、成形不足等缺陷的產生機理和相應對策，重點介紹工藝補充面和壓料面的設計及優化方法，因為拉延是沖壓工藝的關鍵工序，而工藝補充面和壓料面的設計是拉延工序的關鍵，對消除缺陷至關重要。It is determined that with accurate knowledge of the complete stress - strain curve of concrete in compression, steel in tension, and with an iterative computerized non ? linear method, it is possible to predict the entire moment - curvature, moment - flexural rigidity and axial rigidity relation ship of a cross - section of a structure member
可以確定，只要知道混凝土受壓和鋼筋受拉的完整的應力應變關系，採用選代的非線性計算方法，就有可能預測結構截面彎矩一曲率、彎矩一彎曲剛度和軸向剛度的關系。The precision of its calculating results has an direct effect on the design, construction and safe usage. in the typical calculation of the settlement of foundation, additional stress incurring by loading is calculated according to elastic theory which has the same characteristics in semi - indefinated space, the condesion of soil is decided by the condesion experiment of one - demension and the settlement is calculated by adding results of respective layer
地基沉降計算一直是困擾巖土工程技術人員的一個難題，其準確與否將直接影響建築物的設計、施工和安全使用。在經典的地基沉降計算方法中，荷載作用下地基中附加應力場是根據半無限空間各向同性彈性體理論計算的，土體壓縮性是根據一維壓縮試驗確定的，並採用分層總和法來計算地基的沉降量。Obtain these chief research achievements. ( 1 ) the method of hydraulic fracturing, kaiser effect experiment and the finite element numerical simulation computation results, the direction of maximum horizontal principal stress intersect the small - angle of tunnel axial line, it is favorable to the stability of tunnel peripheral rock ; according to the test rust of field stress - relief method, at the present time, zhe gu mount tunnel have n ' t access to high crustal stress site, maximum principal stress magnitude is 17mpa ~ 20mpa
主要獲得以下研究成果： （ 1 ）綜合水壓致裂法、室內巖石kaiser效應試驗和有限元數值模擬計算研究成果，最大水平主應力方向與隧道洞軸線小角度相交，對隧道圍巖穩定性有利；根據現場應力解除法測試結果，目前鷓鴣山隧道尚未進入高地應力段，最大主應力量級為17mpa 20mpa 。In the hogging condition, double bottom and the side shell remain the ultimate bucking strength, deck and upperwing tank remain the yield stress, and the other parts keep elasticity. then the key to calculate the ultimate strength of ship hull girders is to ascertain the ultimate bucking strength of the stiffened panels. in this regard, the developed formulation is designed to be more sophisticated than previous simplified theoretical method for calculating the ultimate strength of stiffened panels under combined in - plane bending and lateral pressure. fabricatio n - related initial imperfections ( initial deflections and residual stresses ) are included in the panel ultimate strength calculation as parameters of influence. all possible collapse modes involed in collapse of stiffened panels, including overall buckling collapse, column or beam - column type collapse, tripping of stiffeners and local bukling of stiffened web are considered
確定了船體梁整體破壞時的剖面應力分佈之後，關鍵在於確定板架的極限屈曲強度。本文充分考慮了在縱向彎曲、橫向壓力作用下加筋板可能發生的幾種破壞模式，即板架的整體屈曲破壞、樑柱形式的破壞、筋的側傾、腹板的屈曲並同時考慮了初始焊接殘余應力、初撓度的影響，使其更精確的計算加筋板的屈曲強度。對于加筋板中加強筋腹板的局部屈曲，採用解析法推導出筋的腹板的撓度方程及其邊界條件，求解相應的方程，從而計算出腹板的局部屈曲應力。For the stress analysis of dryers under the line load of supporting rollers, according to hoff theoretical solution of thin cylindrical shell under line loads, mangelsdorf approximate solution is modified on the basis of the calculation analysis for 14 sets dryers " dimension by computer programming with matlab software. the approximate formulas of the second largest hoop stress of the middle section of the shell are derived
針對托輥線壓載荷作用下烘缸的受力分析，本文根據薄壁圓柱殼在線壓載荷作用下的hoff理論解，在運用matlab軟體對14組常用烘缸參數進行編程計算分析的基礎上，對mangelsdorf近似解作了修正，並由最小二乘法導出殼體中部截面環向應力次大值的近似計算式。At last, the finite element method, the strength reduction method and limit equilibrium method, nature slopes and excavation slopes, lateral stress unloading model and axial loading model are analyzed and discussed relatively
最後，就有限元法、強度折減法和極限平衡法，自然邊坡與挖方邊坡，圍壓卸荷應力路徑模型分析與軸向加荷應力路徑模型分析進行了比較討論。( 2 ) respectively by elastic theory analyses and methods of structural mechanics, transverse static analytical equations for flexible pipeline rigid pipeline are established whose outcomes are applied in numerical example to compare those with that by finite element method. ( 3 ) considering interaction of filled soil, pipeline and foundation, with an eye to non - linear soil model, in view of the initial geo - stress field and the effects of interface between soil and pipeline, and by finite element method the calculational model and method are built for transverse stress in pipeline. then, by the great finite element analytical software ansys, those outcomes are applied in calculation example of positive buried pipe to educe the distribution of circumjacent soil pressure and stresses on cross section and to compare it with that calculated by conventional ways before those outcomes are applied in engineering case of positive buried pipe with flexible filled materials to confirm distribution of soil pressures after the measure for reduction and to compare it with measurements. as a result, the model set up in this paper is proved to be applicable after all above - mentioned analyses
本文基於彈性理論和有限元原理與方法，分析了上埋式地下管道橫向力學計算方法和性狀並探討了上埋式地下管道的減荷等問題： （ 1 ）在分析現有幾種典型的管道垂直土壓力計算方法的基礎上，探討了影響垂直土壓力的主要因素以及改進的方法； （ 2 ）分別通過彈性理論分析法和結構力學的方法，建立了地下管道柔性圓環和剛性管涵的橫向靜力計算方程，並應用在算例中，把所得結果和有限元方法所得結果進行對比分析； （ 3 ）考慮填土、管道和基礎的共同作用、土體的非線性特性、初始應力場以及土體和管道的接觸面因素的影響，利用有限元的思路，建立了地下管道橫向力學有限元計算模型和方法，並且採用大型有限元分析軟體ansys ，針對上埋式管道工程算例，得出了管周土壓力以及管道橫截面應力的分佈狀況和規律，並和理論值進行對比；針對施加柔性填料的上埋式管道工程實例，得出了減荷后的土壓力分佈，並和實測值進行了對比。Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating
箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。Depending on how the ground surface is denuded, the feature of the current crustal stress field and rock stress environment can be calculated analyzing the result in this paper : by analyzing the recovering feature of the elastic deformation of the rockmass in unload - stage under various pressures, it has been found there is close relationship between the recovering degree of the elastic deformation of the rockmass and the unloading degree of the pressure the direction of the major principal stress in the crustal stress field is not consistent with the direction of the crushing stress regional tectonics borne during the last tectonic movement. the evolving degree of the regional geomorphology evidently affects the current crustal stress field, which changes from the self - weight stress field to the horizontal stress field, with the changing of the eroding degree of the regional geomorphology ranging from valley area to hilly country to flat country. in valley area, where there is two stress belts, the bankslope s tress belt and the self - weight stress belt within the mountain. the direction of the major principal stress is nearly parallel to the ground surface and inclines towards the valley in the bankslope stress belt. it is nearly vertical in the self - weight stress belt
通過本文的研究成果，根據區域性地貌的演化特徵，我們可以大致地對現今地應力場進行判斷：在分級卸荷條件下，巖體中彈性變形的恢復具有明顯的規律性，這種規律對于研究地應力場的演變是有幫助的；地應力場中最大主應力方向與區域構造形跡在最近的構造運動中所受區域性擠壓應力的方向無明顯的對應性；區域性地貌形態的演化程度對現今地應力場的特徵具明顯的影響，隨著區域性地貌侵蝕程度由峽谷區、丘陵區、平原區的變化，現今地應力場特徵由自重應力場、水平應力場為主含少量自重應力場特徵向水平應力場的規律變化；在峽谷區，山體中具有兩個應力帶：自重應力帶和卸荷應力帶，最大主應力方向在卸荷應力帶中近平行於坡面並傾向于河谷、在自重應力帶中近於直立；根據原始地面遭剝蝕的程度，可以大致地估算最大主應力和中間主應力的量值和方向；在丘陵區和平原區，最大主應力的方向近於水平，並與附近區域性侵蝕盆地和河流的展布方向基本平行，根據原始地面遭剝蝕的程度，可以大致估算其最大主應力的量值；根據區域性地貌形態的特徵來分析工程區的現今地應力場特徵，並進而大致了解巖石的應力環境，這種分析方法得出的結論與許多實際的地應力測試成果基本一致，對于大型水電工程地下廠房和壓力隧洞的設計是有所幫助的。( 3 ) based on the analyses results of simple inference method and seismic focal mechanism and on the statistic results of measured geostress data, the direction of principal stress was derived and based on the analyses results of macro geological estimate and on the statistic results of measured geostress data the magnitude of principal stress was derived too. the influence of rapidly down - cutting of yellow river on geostress field of studied zone was discussed. then the evolution of geostress field accompanying with the down cutting of yellow river and was simulated with fem and the spatial distribution features of geostress were discussed
根據簡易推斷法、地震震源機制分析法以及地應力實測資料統計分析結果，綜合確定了工程區的主壓應力方向；運用地質宏觀判斷法並結合地應力實測資料的統計分析結果對地應力的量級進行了綜合評價，並進一步討論了黃河快速下切對研究區地應力場的影響；運用有限元法模擬了研究區地應力場的形成過程，並探討了地應力的空間分佈規律。( 1 ) based on the experiments, this thesis discusses the stress loss of vertical prestress caused by deformation of anchorage, the resilience of the tendon and the joint compression ( l2 ), the elastic compression of the concrete ( l4 ) and the relaxation of the tendon ( l5 ). it is concluded that the anchorage deformation is dominated in vertical stress loss. measures are suggested to diminish the loss of the vertical prestress during the design and construction of the bridge
（ 1 ）本文在試驗的基礎上，研究了豎向預應力筋的錨具變形、鋼筋回縮和接縫壓縮損失l2 、混凝土的彈性壓縮損失l4和力筋的應力鬆弛損失l5 ，其中，第一項是最主要的損失，論文據此對設計和施工中如何減小豎向預應力的損失提出了自己的看法和建議。A bearing surface transmits the interaction between an arch dam and its foundation, the strength of which directly affects the constraint of the bedrock to the dam, and thus affects the stress and deformation of the dam. the influence is studied in this paper with nonlinear finite element method, as an example, for a high arch dam in design. the results show that the influence on stress is only limited within the local area near the bearing surface, larger on the maximum principal tensile stress than on the principal compression stress, and the decrease of the strength does not cause unlimited increase of the maximum stress. the influence on the displacement of the top of the dam is smaller than that of the bottom of the dam, especially the relative downstream displacement. at the lower strength of the bearing surface, the relative downstream displacement at the bottom of the dam increases with the decrease of the strength
建基面是傳遞拱壩和基巖相互作用的紐帶，它的強度直接影響基巖對壩體的約束，從而影響壩體的應力和變形.採用非線性有限單元法，以設計中的某高拱壩為例，分析建基面強度對壩體應力和變形的影響.結果表明建基面強度對壩體應力的影響僅限於建基面附近的局部范圍，對最大主拉應力的影響要大於對最大主壓應力的影響，建基面強度的降低不會無限地增大壩體的應力數值；建基面強度對壩頂位移的影響較小，但對壩底位移（尤其是順河向相對位移）的影響較大，當建基面強度較低時，壩底順河向相對位移隨建基面強度的降低而增大In order to reveal load mechanism and failure mode of thick pile caps, by means of the test of 1 / 4 - scale models of thick pile caps with six piles and post - handling study of 3 - dimensional non - linear finite element adina, this paper points out the shortage, which is that the design of pile caps is carried out by flexural strength in chinese technical code for building pile foundations jgj94 - 94 and american reinforcement concrete building construction code aci318 - 02, promulgates that the failure mode of thick pile caps is punching failure and load transfer mechanism is the strut - and - tie, which is that zones of concrete with primarily unidirectional compressive stresses are modeled by compress struts, while tension ties are used to model longitudinal reinforcement over pile
摘要為揭示厚承臺的傳力機理和破壞形式，通過對4個1 : 5比例的六樁厚承臺的模型試驗研究與三維非線性有限元adina的后處理研究，指出中國建築樁基技術規范jgj94 - 94與美國鋼筋砼房屋建築規范aci318 - 02規范中，承臺以彎曲強度進行配筋計算的設計方法之不足，揭示出厚承臺的破壞模式是沖切破壞，傳力機理是以帶有主要單向壓應力的砼區域作斜壓桿，樁頂區域的縱筋作拉桿的空間桁架。On the other hand, for the pre - press stress being threw by the hub was inserted after cooling with liquid nitrogen, the poor transverse tension strength of the multi - ring flywheel rotor could be counteracted. so the rotate speed and energy storage density can be increased efficiently
而採用多環套裝纏繞技術製造的多層飛輪輪環，在利用溫差過盈裝配方法給復合材料輪環施加預壓應力后，能夠有效避免飛輪轉子的復合材料輪環部分因較低的纖維橫向抗拉強度而破壞失效，從而大幅度提高飛輪轉子的極限轉速和儲能密度。In this article, we introducte the advanced numerical, analysis method - finite element method and lucubrate the rigid - viscoplasticity basic theory for three - dimensional problem with the metal ' s specific feature of the warm extrusion forming process, the analytical procedure of metal ductility forming process and the rigid - viscoplasticity finite element method ' basic theory. the rigid - viscoplasticity ' s modle has been made and the rigid - viscoplasticity ' s modle finite element columnwise based on the lagrange facil method and overtension overtress has been deducted in this paper. at the same time, we have analytic studied the forming technique process for the sway oil pump stator
本論文採用先進的數值分析方法? ?有限元法，結合金屬在溫擠壓成形過程的具體特點，詳細論述了三維問題的剛粘塑性有限元法，介紹了金屬塑性成形過程的分析方法，以及剛-粘塑性有限元法的基本理論，建立了剛-粘塑性模形，推導了基於lagrange乘子法和過應力模形的剛粘塑性有限元列式，並對轉向油泵定子的成形工藝過程進行了研究分析。The coherence force c and the inner friction angle of composite increase 115 % - 205 % and 11 % ~ 15 % respectively more than that of no rootstalk soil. 3 the mechanism of dealing with corn rootstalks and eight kinds of blades for experiment in the soil bin have been developed in order to investigating the performance of dealing with rootstalks
土壤-根茬復合體其抗剪強度與剪切面上的法向壓應力成正比，復合體土壤凝聚力c比無根土壤增加115 205 ；內摩擦角增加11 15 。Abstract : in this paper, for the brick structure with frame - shear wall in the first story, the principle of determining the parameters of a laminated rubber bearing such as stiffness, yield strength and axis press stress was discussed ; and the vibration - isolation effectiveness was tested by analyzing a representative project using nonlinear time - history analysis method. some suggestion was made to design and analyze brick structure with ground frame - shear wall on rubber vibration - isolation system
文摘:討論了底框結構橡膠墊隔震層的剛度、屈服強度、軸向壓應力等參數的設計原則，以典型工程為例，採用彈塑性時程反應分析方法，檢驗了底框結構使用橡膠墊隔震層后的隔震效果，對底框結構基礎隔震設計與分析方法提出了一些建議。分享友人