活塞傳動 的英文怎麼說
中文拼音 [huósèzhuàndòng]
活塞傳動
英文
piston drive-
Auto parts : fuel injection system ( valve follower, plunger piston and fuel injection needle, etc. ), power train ( gear, rolling bearing etc. ), piston parts ( packing ring, gudgeon pin etc. ), cam shaft parts ( pin, bush, oscillation beam and some hydraulic components etc. ), others ( gate lock, accouterment etc. )
汽車零部件：燃料噴射系統（氣門挺桿） 、柱塞、噴油針等） 、動力傳動系統（齒輪、滾動軸承等） 、活塞部件（活塞環、活塞銷等） 、凸輪軸部件（銷、襯套、搖臂及部分液壓元件等）和其他部件（如門鎖、內飾等） 。Fluid power systems and components ; cylinders ; basic series of piston strokes
液壓傳動系統和元件.缸.活塞行程的基本系列There is no clutch, gearing, oil changes, smog check, pistons, rings, valves, crankshaft, flywheel, rods, wrist pins, etc., etc
沒有離合器，傳動裝置，機油變化，尾氣檢查，活塞，活塞環，閥門，曲軸，飛輪，連桿，肘節銷，等等。Surface treatment ; determination of characteristics of air driven piston pumps
表面處理.第1部分:空氣傳動活塞泵的特性測定Examine the plunger joint ring of electric hydraulic draw stem and pneumatic draw stem in order to ensure the normal operation of transmission device
定期檢查電液推桿、氣動推桿的活塞密封圈，以保證傳動裝置正常運行。Fluid power systems and components - cylinder - rod wiper - ring housings in reciprocating applications - dimensions and tolerances
流體傳動系統和元件.缸筒.往復用活塞桿刮油漲圈.尺寸和公差The process parameters of electric upsetting include : velocities of upsetting cylinder and anvil cylinder, heating current, preheating length and time, etc. because different materials have different mechanical, electric and thermal characteristics, and there are effects between different parameters, the determination of those parameters becomes a complex problem
電熱鐓粗成形過程的工藝參數主要包括鐓粗缸活塞運動速度、砧子缸活塞運動速度、鐓粗壓力、加熱電流和預熱長度等。這些參數的選擇是一個復雜的問題，其復雜性不僅在於不同的材料具有不同的力學、電和熱傳導特性，而且各參數相互影響、相互制約。Hydraulic fluid power ; housings for elastomer - energized, plastic - faced seals ; dimensions and tolerances ; piston seal housings ; identical with iso 7425 - 1 : 1988
液壓傳動.彈性體賦能塑料面密封溝槽.尺寸和公差.活塞Hydraulic fluid power - cylinders - piston seal housings incorporating bearing rings - dimensions and tolerances
液壓傳動.缸筒.裝有支撐環的活塞密封溝槽.尺寸和公差To solve the heat transfer boundary problem among the piston, liner, coolant and body parts, especially the temperature and heat transfer among the coolant, liner and body
摘要為解決發動機活塞組缸套冷卻水機體之間傳熱邊界條件難以確定的問題，尤其是冷卻水和缸套、機體之間的流固邊界的溫度和換熱系數，將這幾個部件作為一個耦合系統進行傳熱研究。Hydraulic fluid power. cylinder. rod end spherical eye for 160 bar single - rod cylinder, compact serie a
液壓傳動.千斤頂. 160bar小型a千斤頂活塞桿端頭的球頭銷定Piston - linkage mechanism, as the mechanism to transfer the power of engine, bearing the heavy gas - explosive force, inertial force etc, is easy to arise vibration and noise. besides, the joint clearance in mechanism could also irritate the vibration and worsen the dynamic properties of mechanism
作為內燃機動力傳遞機構的活塞連桿機構，由於在周期性的工作循環中，承受著強大的氣體作用力，往復慣性力、離心慣性力等的沖擊，極易引起振動和噪音；同時由於運動副間隙的存在加大了振動的影響，惡化了機構的動態性能。First, the difference between the stm and utm is compared and analyzed. the results show that it can accurately simulate the unsteady flow process of piston wind and the pollutant distribution in tunnel after train left the tunnel, can analyze and calculate the good effect of inertial action of piston wind if using utm
文中首先分析和比較了傳統隧道通風設計所採用的恆定流理論與非恆定流理論的差別，表明運用非恆定流理論不僅更能準確模擬隧道內活塞風的非恆定流動過程，而且能模擬列車通過隧道過程中隧道內污染物濃度的分佈，同時還能考慮利用隧道內氣流（活塞風）慣性作用促進隧道通風，節約通風能耗。Internal combustion engines ; components of rotating piston engines, setup of engine, driving mechanism, definitions
內燃機.旋轉活塞式發動機元部件發動機裝置傳動裝To the problems with changing boundaries, such as fire hazard, combustion in cylinder, the traditional methods must suffer from the drawbacks of tedious process in meshing and remeshing. meshless method is a new method, which uses a set of points to discretize the problem domain
對於火災、活塞式發動機等燃燒過程，其求解域連續變化，使用傳統的方法求解這類問題將面臨復雜和繁瑣的網格初置與重構過程。分享友人