液壓表 的英文怎麼說
中文拼音 [yèyābiǎo]
液壓表
英文
charging water gauge-
First, a simple discussion for the mechanism about electrostatic atomization of the liquids has been given ; then the paper theoretically analyzed waving course, liquid drop producing course, and the liquid drop diffusing course in electrostatics atomization process., gave an analysis about the methods about carrying charges to the liquid drop, and analyzed that liquid with high electrical conductivity can be carried charges and atomized by electric field, while the isolated liquid with low electrical conductivity can be charged fully with the soakage electrode and inducing charge methods. at last the paper designed and configured the experimental equipment, conducted the atomization experiment to the three liquid medium - kerosene, emulsifier and alcohol under the same environment, handled the experimental results, then summarized the relationship between liquid electrostatic atomization effect and liquid surface tension, electronic conductivity and viscosity, along with the influence of voltage to electrostatic atomization and so on, found out the liquid atomization rule in high voltage electrostatic field
首先，對液體介質的靜電霧化機理作了初步的探討，理論上分析了液體霧化過程中射流區、波紋區、霧滴區和霧滴擴散區;然後對液體荷電方法進行了研究分析，對于高電導率的液體，場致荷電和接觸荷電可以使其霧化，而對于電導率較低的絕緣液體，需用浸潤電極荷電和感應荷電方法使其充分帶電;最後，根據前面的研究分析，設計和組裝試驗裝置，在同一環境下對煤油、乳化劑、酒精三種不同液體介質進行高壓靜電霧化試驗，並對試驗結果進行分析處理，總結出液體靜電霧化與液體表面張力、電導率和粘度的關系及電壓對液體靜電霧化的影響等，得出高壓靜電場中液體霧化的一般規律。In the course of working, ， the plow will make use of the shuttling method so that it can dig alternately either on the left or on the right. compared to the unilateral plow, it can improve the productivity because it can help leave off the soil 、 take from the consumed energy and reduce the empty journey. to meet the requests above, we will use a remote cylinder with both a small cubage and double functions, approximately designing the plow to be columniform and symmetric. after the experiment for a period in the field, we found that the most frayed areas had happened at the places of both plow shank and share and at the same time the base of the remote cylinder had ruptured suddenly
與單向犁相比，其優點在於：耕地無開、閉壟，地表平整，降低了耕后整地的能量消耗，減少了地頭的空行程，因而大大提高班次生產率。為了滿足犁體梭式作業的要求，我們採用了一隻小容積雙作用的液壓油缸；同時對犁壁曲面的形狀採用了近似圓柱形的對稱設計。但經過一段時間的田間試驗，我們發現：該犁犁胸部分的犁脛和犁鏵上的犁尖在工作中磨損較為嚴重；主犁梁和油缸缸體的連接部分（即油缸底座）突然發生了斷裂，造成整個犁體無法正常工作。In accordance with the surface area of the piston, the force acting on it is transferred to the hydraulic fluid and from there via the connecting tube to the measuring instrument
根據活塞的表面積，作用在活塞上的力傳遞到液壓油，然後從那裡通過連接管到達測量儀器。In accordance with the surface area of the piston the force acting on it is transferred to the hydraulic fluid and from there via the connecting tube to the measuring instrument
根據活塞的表面積的大小，作用在活塞上的力轉移到液壓油，然後從那裡通過連接管到達測量儀器。The pressure drop of the compound tray can be regarded as consisting of dry plate pressure drop, clear liquid resistance, liquid surface tension resistance, and packing pressure drop. the model that has established can fairly predict the pressure drop of the compound tray, the value calculated by the model compared with that detected by experiment is less than 20 %
復合塔板的壓降可認為由干板壓降、清液層阻力、填料層壓降和克服液體表面張力的壓降四部分組成，所建立的壓降計算模型，能較好地預測復合塔板的壓降，計算值與實驗值誤差在20以內，可用於工程設計。Our company was established in 1982, possesses finish machining equipment numerically controlled machine, engine lathe, high precision instrument lathe, thread - rolling machine, hobbing machine and milling machine etc, specializes in producing textile machinery fittings, hydraulic fitting pipe, automobile and moto - rcycle fittings and plastic fittings etc. the products have been sold all over china and sold to as far as middle east, southeast asia etc
我公司創建於1982年，擁有數控車床，普通車床，高精度儀表車，滾絲機，注塑機，磨床，鋸床，銑床設備等各種精加工設備， ，專業生產液壓管接頭，紡織機械配件，汽摩配件及塑料配件等，產品銷往全國各地，並通過外貿公司遠銷海外市場。Hydraulic control system of double - cylinder vessel gate is a sort of typical electrohydraulic proportional control system0 in order to study electrohydraulic flux control characteristics of this system, i have analyzed the principle of this hydraulic control system, and made its mathematics model ? in double - cylinder hydraulic system, it is necessary to process electric synchronous control in this hydraulic system, this paper also introduces a sort of fnn ameliorated from the point of view of intelligent control theory, and clarifies the principle of applying that network to achieve synchronous controlo at the same time, the means of fuzzy configuration analysis is used for network training, the comparative experiments make known that the method of applying fnn to realize synchronization control is feasible, furthermore, its effect is better than others0 this paper puts forward that a distributed control system can be used to monitor and control vessel gate within a real - time or remote distance, the basic project, structure, applications and functions of computerized scada system in hydraulic system of vessel gate is introduced ? a double layer network structure, epigynous and hypogynous machine network, is applied to this system, in accord with the application of technique such as plc, integrated software etc, this paper introduces the methods and application to achieve the computerized scada system in the task, and analyzes the characteristic of this system, in this paper, the application of configuration in monitor and control system of vessel gate is discussedo in addition, in accord with the application of technique such as visual basicb
雙缸船閘液壓啟閉控制系統要求解決同步控制問題，文中從智能控制理論角度出發，採用了一種改進的模糊神經網路，結合模糊聚類分析方法，闡述了應用該網路實現同步控制的原理。通過對比模擬實驗表明：應用模糊補經網路實現同步控制是可行的，而且它的同步控制效果要優于傳統的設置主從令缸控制方法，具有良好的魯棒性能。另外，本文提出了建立船閘控制系統的分散式控制系統，介紹了船閘液壓控制系統的計算機監控系統（ scada ）的方案、結構、應用和主要功能，採用雙層網路化結構：上位機網路和下位機網路，並結合plc通信網路技術和組態軟體等技術構成的計算機監控系統的實現方法，實際應用，分析了這種較新的系統模式在船閘液壓控制系統的計算機監控系統的功能實現中所具有的特點。With the deveiopment of hydraulic technology, hydraulic system and hydraulicequipment are more complicated, hydraulic technology is more widely and morecomp1icatedly used in agricultural machine and their malfunction is more difficu1t to bedetected. fault diagnosis of hydraulic system is not as apt to be observed as that of themechanical equipmeflt or is not as easy to be detected as that of electric equipmeflt bymu1tipurpose meter or other meters. flux meter gage and pressure gage ca n ' t meet the needof fault diagnosis for hydraulic system because its working medium and workingcomponents are hiding inside the sealed vessel
隨著液壓技術的發展，液壓系統及液壓設備越來越復雜，液壓技術在農機上的應用也變得廣泛而復雜，農機液壓系統的故障診斷也越來越困難，液壓系統的故障診斷不象機械設備那樣直觀，也不象電氣設備那樣通過萬用表等儀器測得，液壓系統的工作介質和工作部件都在密閉的容腔內，流量計、壓力表等測量儀器遠遠不能滿足故障診斷的需求。Our factory mainly manufactures hydraulicfllfers, filter oil vehicles, hydraulic air cleaner, liquidlevel gage and liquid thermometer, liquid level control relay, switch of manometer, combined sealing washer, piezometer soft tebe assembly, andso on. we also carry on all kinds of non - standard, and bring in filters, air cleaner, liquid - level gage and liquid thermometer and complete set of design and manufacture of hydraulic system
本廠主要生產各類液壓過濾器、濾油車、液壓空氣濾清器、液位液溫計、液位控制繼電器、壓力表開關、組合密封墊圈、測壓軟管總成、塑料管夾等產品，還承接各類非標、引進過濾器、空氣濾清器、液位溫計及成套液壓系統設計與製造。Abstract : requirements for hydraulic steering rack cylinder are very high, the rack cylinder should be durable, lubricants preservable and of seal. so, finish machining and parameter - set are necessary
文摘:液壓轉向機對齒條桿部表面有很高的耐磨、儲油、封存要求，為此需要一套表面超精加工工藝及加工參數設定。Hydraulic fluid power - cylinder actuator mounted valves - standard dimensions for mounting surfaces
液壓氣動缸傳動安裝閥安裝表面的標準尺寸Moreover, the resulted prediction model of foam size of the closed cell aluminum foam was verified by comparison to the experimental results from the foaming process at different foaming conditions, and the predicted bubble diameter is in good agreement with the experimental ones, the relative error distributes between - 5. 04 % and 6. 32 %
當入射空氣的壓強、氣流量，液面高度，出氣孔直徑增大時，氣泡直徑隨之增大；當出氣孔數量，液體粘度增大時，氣泡直徑減小，表面張力對氣泡直徑的影響可以忽略不計；靜態條件下液體表面氣泡直徑的預測值和實驗測量值符合得較好，相對誤差分佈在- 5 . 04 % ~ 6 . 32 %之間。9 series pressure cavity is made of stainless steel single unit integration structure by processing so may guarantee for the better seal performance. the characteristic of product are no o - ring, no welded, no silicon oil or other organic, structural durability ; the most apply to pump and compressor, liquid pressure and pneumatic system, go - anywhere vehicle, energy and water processing system, pressure instrument, refrigerating equipment, agricultural machinery device, locomotive braking system
9系列壓力腔採用不銹鋼單件一體式結構加工而成，因而可以保證較好的密封性能， 9系列產品的特點是無o形圈無焊縫無硅油或其它的有機物，經久耐用，主要應用於泵及壓縮機，液壓及氣動系統越野車能源及水處理系統壓力儀表冷凍設備農機設備機車剎車系統。Main products include : inside - lining code printer series, shoe box code printer series, gilding press and making machine series, leather slitter series, pneumatic button sewer series, gangbao moistening machine series, glue spreader series, line blower series, automatic mid - sole printer series, upper - sheeting hammer machine series, series of wrinkle - removing ironer for shoes, leather ironing machine, automatic hydraulic pressure - closing series, production - line code printer series, upper - sheeting and heel modular machine series, automatic and semi - automatic heel - nailing machine etc
主要產品有：里皮打碼機系列，鞋盒打碼機系列，燙金機、烙印機系列，皮革切條機系列，氣動釘扣機系列，港寶沾濕機系列，上膠機系列，吹線機系列，自動中底打碼機系列，鞋面錘平機系列，鞋類除皺燙平機系列，皮革燙平機系列，自動液壓壓合機系列，流水線印表機系列，鞋面、後跟定型機系列，全自動、半自動裝跟機系列等。In addition, resovling the base for fixing actuator in the part of setting and debugging of whole test bench ; indicating performance of the test bench reliability and the test data is accord with correlative standard and may be taken as the bases of trouble shooting and maintain for tractor hydraulic lift system through testing the hydraulic lifter ' s static performance of tractor newholland 110 - 90. postgraduate : shenggang luan major : mechanism design and theory tutor : prof. bolin mi
試驗臺的安裝與調試主要是完成加載油缸的地基處理，而在試驗部分通過對紐荷蘭110 - 90型拖拉機液壓提升器的靜態性能的檢測，表明本試驗臺性能可靠，所得到的試驗數據滿足相關標準中規定的精度要求，可以作為拖拉機液壓懸掛系統故障診斷和預知維修的依據。In the design of loading - frame, puting forword a group of universal dimensions of three - point free - link attachment to category i and ii tractors through comparing and analysing whose scope of dimensions, thereout, working out sketch of loading framework on several different positions in the whole lift - course of hydraulic liftenafter this. analysing the case of force on loading framework when the loading force equal to 44100n and the lift - position of the hydraulic lifter is on upper limit, and giving a data table about the case of force on all these positions, consequently, completing the design of loading frame
在加載框架的設計部分，通過對、類拖拉機的三點懸掛機構桿件尺寸范圍的比較分析，給出了一組、類拖拉機通用的三點懸掛機構桿件尺寸，由此作出了液壓提升器提升全行程中幾個不同位置的加載機構簡圖，並按44100n的加載力、以上極限位置為例對加載機構進行了受力分析，並給出了包括其它幾個位置在內的受力情況表，進而完成了加載框架的設計。The three newly developed ones by the author are introduced, which have individual distinguished features besides remaining advantages of ordinary gear pumps, and can be widely used in hydraulic transmission systems
研究表明，這些新研製的齒輪泵均保留了普通齒輪泵的優點，同時還具有各自的特點，可廣泛用於液壓傳動系統中。In the planning of the hydroforming process, the paper analyzes a representative automobile part to build up the cae simulation model of tube bending, preforming, and hydroforming, and discusses the influence of different preform designs on the final shape of the tube
在管件液壓成形製程規劃方面，本文選取了一具有代表性的汽車結構件進行分析，由原始的彎管、預成形、到液壓成形皆建立了cae模擬模式，並探討不同的預成形設計方式對管件最終成形之影響。The autonomous underwater vehicle which carries liquid oxidizer and liquid incendiary agent and uses the outside seawater as coolant request the oxidizer 、 incendiary agent and coolant can supply the power system according to accurate proportion and reasonable flow on any condition. the system should have small volume and light weight and should be easily realized. the system and control mode introduced in this article can fit these requirements well
控制或降低液壓系統油液的污染度和提高液壓元件的污染耐受能力是確保液壓系統可靠工作的兩個重要方面，本文分析了液壓柱塞泵所在系統油液污染特性一定時影響泵污染耐受能力的諸多因素，指出了在結構形式確定的條件下設計高污染耐受度液壓柱塞泵所要求的摩擦副材料與主要表面工藝Specifications for hydraulic surface - check type lubricating nipples for aircraft
航空用液壓表面止動型潤滑脂嘴規范分享友人