液體流動噪聲 的英文怎麼說

中文拼音 [yètǐliúdòngzàoshēng]
液體流動噪聲 英文
liquidborne noise
  • 液 : 名詞（液體） liquid; fluid; juice
  • 體 : 體構詞成分。
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 噪 : 動詞1. （蟲或鳥叫） chirp 2. （大聲叫嚷） make noise; make an uproar; clamour
  • 液體 : liquid; liquor; fluid
  • 流動 : 1. （液體或氣體移動） flow; run; circulate 2. （經常變換位置） going from place to place; on the move; mobile
  1. Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle

    流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。
  2. Hydraulic fluid power - test code for determination of airborne noise levels - part 3 : pumps - method using a parallelepiped microphone array

    液壓流體動力.氣載噪聲級測定的試驗規程.第3部分:泵.採用平行六面體麥克風排列法
  3. Hydraulic pound, vibrate, noise and cavitation are the main difficult problems in water hydraulic valves, and finite element numerical analysis is proved to be an effective computational method, so numerical simulation and visualizing research on the flow field in water hydraulic valves by applying finite volume method is very important

    水壓閥中的液壓沖擊、振動、噪聲以及水壓閥中的氣蝕是研製水壓閥存在的主要難題，而有限體積數值計算方法又被證實是一種可行而有效的流場計演算法，因此應用有限體積法對水壓閥閥道內流場進行數值模擬和可視化研究，是非常有意義，也是非常重要的。
  4. Firstly, the current testing localization in the detection of electric bow is analyzed and the new system ' s whole construction developed in this thesis is introduced ; in the 2rd chapter, the embedded 110v dc power supply is analyzed and constructed, and with experiments, some dissonant results such as the fluctuation of output pwm ( pulse width modulation ) pulses, the power noise added to output voltage, and the drop of output voltage have been analyzed and the problems have been broken down one by one ; in chapter 3, stepping motor ' s drive has been systematically dissertated, and combing stepping motor ' s subdivided drive technology, the author develops an intelligent mini - step driving circuit using a main - sub microprocessor structure, which is validated in the hybrid stepper based system ; in the 4th chapter, liquid crystal driving and displaying technology is specified in detail, with one sort of lcd modules ( tlm12864h ), the author develops an feasible circuit for the new testing system, designs a menu mode based program struc ture and brings here some programming codes using franklin c51 programming language ; in chapter 5, the above built system is used in the electric bow ' s practical detection, and the differentiating rate of this system is analyzed

    論文首先分析了目前機車受電弓檢修方式存在的局限並概述了本論文研製的受電弓測試系統的體系架構；第二章對系統內置110v直流控制電源進行了分析和設計，結合試驗對輸出pwm振蕩、輸出電源噪聲大、輸出電壓下跌等現象進行了分析並提出解決措施；第三章論述了步進電機的驅動，結合步進電機微步驅動技術研製了基於上下位單片機組的混合式步進電機智能驅動電路，並在試驗中得以驗證；第四章詳述了液晶驅動及顯示技術，利用一款液晶顯示模塊tlm12864h研製出本系統用液晶顯示電路，設計了菜單式的程序結構並以franklinc51編程方式給出部分子程序代碼；第五章則將以上構建的整個系統應用在機車受電弓的實測中，並對測試解析度進行了分析。
分享友人
分享到 Line

分享到臉書