滑動小齒輪 的英文怎麼說
中文拼音 [gǔdòngxiǎochǐlún]
滑動小齒輪
英文
sliding pinion- 滑 : Ⅰ形容詞1 (光滑; 滑溜) slippery; smooth 2 (油滑; 狡詐) cunning; crafty; slippery Ⅱ動詞(貼著物...
- 小 : Ⅰ形容詞1 (體積、面積、數量、強度等不大) small; little; petty; minor 2 (年紀小的; 年幼的) youn...
- 齒 : Ⅰ名詞1 (牙; 牙齒) tooth 2 (物體上齒形的部分) a tooth like part of anything 3 [書面語] (年齡...
- 輪 : Ⅰ名1 (輪子) wheel 2 (像輪子的東西) wheel like object; ring; disc 3 (輪船) steamer; steamboa...
- 滑動 : slither; slippage; slipping; slide; sliding; run; sliding movement [motion]; glide; slump滑動閘門...
- 齒輪 : gear [rack; toothed] wheel; (toothed) gear; wheel gear
-
Apply to airproof manual shift gear - box and self - automatism shift gear - box lubricated bu gear oil. axletree andpusher of carriage, truck, car, vehicles of architecture and agreculture
適用於密封手動變速齒輪箱,以及齒輪潤滑的半自動變速齒輪箱;客車、貨車、小車、建築及農業器械的車軸及后推齒輪。Vertical motion of the carriage is provided by a pulldown gear case coupled by two pinions to racks on the mast
滑架的垂直移動是由一個下拉齒輪箱提供的,該下拉齒輪箱則通過兩個小齒輪連接到支架上的齒條上。Based on the theories of gear engagement, contact analysis, friction and heat transfer, a three - dimensional finite element model of gear tooth was established to investigate temperature distributions and variations along the contact path over a range of applied loads and operating speeds with consideration of lubrication conditions. sensitivity analysis of surface temperature to gear configuration, frictional heat flux, heat transfer coefficients, and oil and ambient temperature was conducted and the major parameters influencing surface temperature were evaluated
本文基於齒輪嚙合原理、輪齒接觸分析、摩擦學和傳熱學,以有限元分析方法和理論分析計算相結合為手段並以實驗測量結果作為參考,建立了適用於工業應用並具有較高計算精度的高速齒輪傳動輪齒溫度分析的模型和方法,系統地分析了輪齒本體溫度的大小和分佈以及齒輪幾何、載荷及轉速和潤滑冷卻條件等對輪齒本體溫度的影響。Tooth surface temperature and thermal equilibrium conditions have significant effects on gear performance and failure as well as lubrication system in high - speed gear transmissions for aerospace applications
高速重載齒輪傳動系統的熱平衡狀態以及輪齒表面溫度的大小對齒輪傳動的性能與失效以及齒輪潤滑系統的設計與操作控制等有著重要的影響。Taking gear without tooth face invalidation such as agglutination and abrasion as a precondition, and according to the relation between minimal oil film thickness and tooth face roughness of elastic liquid dynamic pressure lubrication theory, viscosity of gear lubrication oil was educed by reliability method in this paper, and the calculation formula has been elicited and applied
摘要以齒輪傳動不發生膠合、磨損等齒面失效為前提,根據彈性流體動壓潤滑理論的最小油膜厚度與齒面粗糙度的關系,用可靠性方法確定齒輪潤滑油的粘度,給出計算公式並進行了實例計算。By this method, the gear drives have small sliding coefficients and contact stress. therefore, the gear wear is effectively reduced
使用所提方法可以使齒輪具有較小的滑動系數和接觸應力,從而有效地減小了齒輪的磨損。分享友人