滑柱塞 的英文怎麼說

中文拼音 [gǔzhùsè]
滑柱塞 英文
slijoint
  • 滑 : Ⅰ形容詞1 （光滑; 滑溜） slippery; smooth 2 （油滑; 狡詐） cunning; crafty; slippery Ⅱ動詞（貼著物...
  1. Analysis and improvement on the plunger lever ' s slip from the oil cylinder of the bascule door ' s actuator on 100t landing craft

    100噸登陸艇吊門傳動裝置油缸柱塞桿滑脫的分析與改進
  2. The paper analyses the stress and relative motion of piston / cylinder and swash plate / slipper matching pairs in water hydraulic pisto n pump, based on which the proper experimental research method is determined

    對水壓柱塞泵柱塞、滑靴摩擦副的受力和相對運動形式進行了分析，確定了摩擦副合理的試驗研究方法。
  3. Kinematics of the axial piston pump with swash plate yoke ' s angle were analysed. there was a lot of analysis about relative movement between piston and cylinder block, between piston and swash plate, between slipper and swash plate. at same time, the movement simulation curves were given

    對軸向柱塞泵進行運動學分析，重點是對柱塞與缸體之間，柱塞與斜盤之間以及滑靴與斜盤之間的相對運動進行分析，並且分別給出了模擬曲線； 2
  4. Besides establishing the calculation formulas of the support force of the swash plate, the contact load and the friction force between piston and cylinder block, the interaction force between piston and slipper, and the heel over moment of slipper, the relation between each machinery parameter and all these forces were discussed. 3

    分析了柱塞和滑靴的受力情況，並推導出斜盤支承反力，柱塞與缸孔間的正壓力和摩擦力、以及柱塞與滑靴間的作用力和滑靴傾側力矩的計算公式； 3
  5. As one of the four important parts of water hydraulic axial piston pump, the design of sliding shoes friction matching mainly takes hydrostatic bearing

    作為水壓軸向柱塞泵的四個關鍵組件之一，滑靴摩擦副的設計主要採用靜壓支承的方法。
  6. Ma yan ? ying, liu jia ? qi. experimental investigation of oil film of port plate / cylinder block in axial piston pump j. lubrication engineering, 1999, 3 : 3539

    鄭煒， ?有雄，魯寶香.軸向柱塞泵配流副油膜的實驗研究j .潤滑與密封， 1995 ， 5 ： 3739
  7. Zhou shi ? yu, duan zhan ? xu. experimental investigation of gap of port plate / cylinder block in axial piston pump j. chinese hydraulic & pneumatic, 1986, 3 : 1214

    許耀銘.軸向柱塞泵滑靴和配流盤摩擦副的設計與實驗研究j .液壓與氣動， 1977 ， 2 ： 312
  8. Swing mechanism comprises an axial piston motor with cushion valve and a planetary gcear reducer. fully sealed singlerow ball swing ring with monobloc internal teeth, grease bathed

    帶有緩沖閥的軸向柱塞馬達與行星齒輪減速機組成的回轉機構，單列球型整體內齒式全密封回轉支承，油脂潤滑。
  9. The forces acting on a sliding hoot, the key element of swash - plate axial piston pump. are analyzed and the formulas computing squeezing and repelling forces are derived ; the redundant squeezing force method is presented, including the selection of parts materials, squeezing force factor and the determination of geometric parameters of a sliding hoot

    摘要分析了斜盤式軸向柱塞泵的關鍵摩擦副零件滑靴的受力，導出了壓緊力和分離力的計算公式；介紹了滑靴設計方法中的剩餘壓緊力法，包括零件材料、壓緊力系數的選擇以及滑靴關鍵幾何參數的確定。
  10. This task will be foundation to develop a new type hydrostatic transmission piston pumps with high efficiency, long life, high pressure and high speed, which combined the item of nature science fund of zhejiang province, tribology study on sealing, hydrostatic support and piston on hydrostatic transmission piston pump. in this paper, a new design idea of the ball friction coupling based on hydrostatic bearing was given, and analysis was carried out to the static state properties and the dynamic properties of the oil - film of this friction pair

    本課題是結合浙江省自然科學基金項目「靜壓傳動柱塞泵的密封、靜壓支承和柱塞的摩擦學研究」 （ 501073 ） ，為研發高效率、長壽命、高速、高壓靜壓傳動柱塞泵提供一定的理論基礎，著重研究了滑靴副和球鉸副的動靜態特性，提出了基於靜壓支承的球鉸副設計原理。
  11. Constructure forms and work principles of hydraulic vavle lifter ( hvl ) in four kinds of classic internal conbustion engine is introduced ; designment and application of oil - intake line, oil - reservoir volumn, and limit position of plunger running in hvl and requirement of hvl on lubrication system and valve train mechanism of internal combustion engine are analyzed ; in the meanwhile, corresponding solutions are put forword

    摘要介紹了4種典型內燃機液力挺柱的結構形式及工作原理，對液力挺柱在設計和應用中進油道、儲油室容積、柱塞工作極限位置及液力挺柱對內燃機潤滑系和配氣機構的要求等幾個問題進行了分析，並提出了相應的解決方法。
分享友人
分享到 Line

分享到臉書