滑柱式 的英文怎麼說
中文拼音 [gǔzhùshì]
滑柱式
英文
strut type-
In order to approach the optimum design of changeover portion structural shapes for submarine ' s different diametral pressure cabins, a new structural type, named the double arc transition form, is introduced based on the analysis of stress concentration, by using the engineering calculation method and finite element mthod
摘要為了探討潛艇不同直徑的耐壓艙室過渡段結構型式的最優設計，利用工程計算方法和有限元方法，分析過渡段結構的應力集中，提出了能夠使不同直徑圓柱殼光滑過渡的結構形式雙圓弧式過渡形式。Based on extensive investigation of construction technique history of chinese ancient buildings, the structure method, structure developing history and seismic behavior of chinese ancient timber structure buildings are analyzed in several respects of the structural system and form. through a series of experiments on constituent parts of chinese ancient timber building structure, including the tests on the corbels and brackets called dougong subjected to low cyclic reversed loadings, the tests on the wooden frame using the tenon - mortise joints as connections of column and beam subjected to low cyclic reversed loadings, the tests on vibration isolation effect of friction and slippage between column footing and their socle base, and a series of shaking table tests on a chinese ancient timber structure palace building mode under artificial earthquake at serving conditions, destroyed conditions and reinforced conditions, many valuable results of structures such as moment - curvature hysteretic loops of dougong structure and tenon - mortise joints under low cyckc reversed loadings, the static function, the seismic performance, energy dissipation, vibration reduction, energy - loss mechanism, nechanicalmode and failure mode were studied. aplenty of valuable parameters of the structure system were obtained, such as the natural period of structure, vibration modes, damping ratio, factor of vibration isolation, oscillate amplitude of ineitial accebration, velocity and displacement, magnitude of slippage, and the mechanism of structure failure and collapse etc. based on these research, the complete analysis of ancient timber structure under earthquake were carried out in which including mechanism analysis method, calculating mode, strength analysis of members and joints, strengthening methods for serving damaged ancient timber structure buildings were also taken into account
依照宋代《營造法式》建造了抬梁式殿堂木結構構件及結構模型，對中國古代木結構中的典型構造如：柱腳在礎石頂面平擱簡支、柱架榫卯連接、柱高不越間之廣、側腳、生起、斗拱等的構造機理及結構功能進行了量化分析和實驗研究： （一）通過木柱石礎靜摩擦試驗，測定了柱腳與石礎古鏡面間的摩擦系數及摩擦力隨上部結構荷載變化的規律； （二）通過單柱承載力試驗，測定了古建築中木柱的受力變形特徵、破壞模式、及模型材料的變形模量、極限承載力、極限變形等參量； （三）通過柱架低周反復荷載試驗，測定了柱架的抗側移剛度、柱架恢復力特性及滯回曲線、榫卯張角剛度及其變化規律、柱架及榫卯的極限承載力和極限變形、及榫卯減振參數； （四）通過斗?低周反復荷載試驗和受壓試驗，測定了古建築木構件與木構件間摩擦系數，斗?抗側移剛度，斗?恢復力特性及滯回曲線，斗?抗壓極限承載力及受力變形規律； （五）通過抬梁式殿堂間架模型振動臺試驗，測定了殿堂木構架結構自振周期，地震反應振形、阻尼特性及阻尼比；按結構分層特點對柱腳、柱頭和斗?層上的屋蓋的地震反應採用多點同步測量，對柱根滑移、榫卯變形、斗?的變形、復位、耗能減振參數等進行了定量分析。The paper analyses the stress and relative motion of piston / cylinder and swash plate / slipper matching pairs in water hydraulic pisto n pump, based on which the proper experimental research method is determined
對水壓柱塞泵柱塞、滑靴摩擦副的受力和相對運動形式進行了分析，確定了摩擦副合理的試驗研究方法。Besides establishing the calculation formulas of the support force of the swash plate, the contact load and the friction force between piston and cylinder block, the interaction force between piston and slipper, and the heel over moment of slipper, the relation between each machinery parameter and all these forces were discussed. 3
分析了柱塞和滑靴的受力情況，並推導出斜盤支承反力，柱塞與缸孔間的正壓力和摩擦力、以及柱塞與滑靴間的作用力和滑靴傾側力矩的計算公式； 3Swing mechanism comprises an axial piston motor with cushion valve and a planetary gcear reducer. fully sealed singlerow ball swing ring with monobloc internal teeth, grease bathed
帶有緩沖閥的軸向柱塞馬達與行星齒輪減速機組成的回轉機構，單列球型整體內齒式全密封回轉支承，油脂潤滑。The forces acting on a sliding hoot, the key element of swash - plate axial piston pump. are analyzed and the formulas computing squeezing and repelling forces are derived ; the redundant squeezing force method is presented, including the selection of parts materials, squeezing force factor and the determination of geometric parameters of a sliding hoot
摘要分析了斜盤式軸向柱塞泵的關鍵摩擦副零件滑靴的受力，導出了壓緊力和分離力的計算公式；介紹了滑靴設計方法中的剩餘壓緊力法，包括零件材料、壓緊力系數的選擇以及滑靴關鍵幾何參數的確定。Secondly, by making use of the features of lattice frame anchor structure which can protect slope and retain stability of landslide together with its small space between beams and light anchor, the calculation model and formulas of slope force are dealt with and the design process of lattice beam and pillar as well as anchor and plate are introduced carefully
利用格構式錨桿框架結構所採用的小間距、小噸位錨桿及連續格構樑柱，從而使格構樑柱受力較均勻，適合鬆散堆積體滑坡治理的需要，即同時滿足深層抗滑和淺層護坡。Among the results of these researches, cylindrical gears with curvilinear tooth trace have merits as follows : higher bending stress, low noise, better lubrication conditions, and no thrust forces. so this kind of gear can be considered to substitute the helical gear and herringbones
本文提出的弧齒線圓柱齒輪是一種新型齒輪傳動形式，具有傳動平穩、噪聲低、潤滑性能良好、輪齒彎曲疲勞強度大的特點，因此該齒輪可以作為斜齒輪和人字齒輪的替代品用於高速重載場合。( 2 ) the paper uses two methods to analyse the falsework structure and then get the basic data to guide the construction and installation of the falsework in sliding construction. these data play an important role in practice
（ 2 ）基於扣件式鋼管腳手架設計規范、鋼框架格構柱兩種方法對胎架結構受力進行分析，進而得出能指導滑移施工中胎架的構造及搭設的基本數據，其結果對工程實踐有重要的指導作用。Series b combines a modified a valve with a male luer lock adapter
系列a有能與無針滑扣式接頭柱頭適配的母型滑扣式介面Slider type automatic holder for cylindric shank broach. dimensions
滑塊式自動圓柱柄拉刀夾頭.尺寸Slider type manipulative holder for cylindric shank broach. dimensions
滑塊式手動圓柱柄拉刀夾頭.尺寸In addition, instead of portal brake of j93 - 1000b model, the brake device of j93 - 1000c changes into rushing board brake, thus the dependability of braking is consumedly advanced, being convenient to adjust, and the rigidity strengthening of plate design reduces the vibration noises during the working of press. with cast steel as the material of slide, slide weight of j93 - 1000c model is increased 1 thousand kgs than j93 - 1000b model with nodular cast iron as material. plus that the width from front and back of frame upright post of j93 - 1000b model is 750mm, while its 1000mm for j53 - 1000c model, increasing 250mm than the former
J93 - 1000c螺桿螺母螺旋副使用壽命及螺桿的剛度也增加剎車裝置由原j93 - 1000b型門剎車改為j93 - 1000c推板式剎車，制動可靠性大大提高，而且便於調整，平臺設計剛度增強降低了壓力機工作中的振動噪聲j93 - 1000c型滑塊支背材質鑄鋼j93 - 1000b型的為球墨鑄鐵而且j93 - 1000c型滑塊重量比j93 - 1000b型增加1000公斤， j93 - 1000c型機架立柱前後寬1000毫米比j93 - 1000b型機架立柱前後寬750毫米增加250毫米， j93 - 1000c機身重46 . 8噸， j93 - 1000b整體機身重38 . 5噸。In addition, instead of portal brake of j53 - 1000b model, the brake device of j53 - 1000c altered into rushing board brake, thus the dependability of braking is consumedly advanced, being convenient to adjust, and the rigidity strengthening of plate design reduces the vibration noise during the working of press. with cast steel as material of slide, slide weight of j53 - 1000c model is increased 1 thousand kgs than j53 - 1000b model with nodular cast iron as material. plus that the width from front and back of frame upright post of j53 - 1000b model is 750mm, while its 1000mm for j53 - 1000c model, increasing 250mm than the former
J53 - 1000c螺桿螺母螺旋副使用壽命及螺桿的剛度也增加剎車裝置由原j53 - 1000b型門剎車改為j53 - 1000c推板式剎車，制動可靠性大大提高，而且便於調整，平臺設計剛度增強降低了壓力機工作中的振動噪聲j53 - 1000c型滑塊支背材質鑄鋼j53 - 1000b型的為球墨鑄鐵而且j53 - 1000c型滑塊重量比j53 - 1000b型增加1000公斤， j53 - 1000c型機架立柱前後寬1000毫米比j53 - 1000b型機架立柱前後寬750毫米增加250毫米， j53 - 1000c機身重46 . 8噸， j53 - 1000b整體機身重38 . 5噸。Abstract : this paper derives thecalculating formulas to the contact strength and oil - film thickness of the involute spur gear according to hydrodynamic lubrication principle. through check with test, shows that they may rully replace now available hertz formula and dowsonformula respectively
文摘:根據流體動力潤滑原理，推導出了漸開線直齒圓柱齒輪接觸強度及油膜厚度的計算公式，通過實驗驗證，說明它們可以完全分別代替現有的赫芝公式及通森公式。20 src eccentric loading specimens were designed taking the relative eccentricity e0 / h the slendemess ratio 10 / h as the factors. according to the mechanical behavior of eccentric loading columns, unidirectional embedded electronic steel - concrete slip transfers and double - directional embedded electronic steel - concrete slip transfers were respectively placed inside these 20 specimens and electronic strain gauges were also installed on the steel shape flanges webs and concrete. the change of the mechanical behavior and interior slip of the 20 specimens in the whole process of loading was fully observed
設計了以長細比、偏心距為主要參數的20個偏壓柱試件，根據偏壓柱的受力特性，在試件中分別放置了單向內置式鋼?混凝土電子滑移傳感器和雙向內置式鋼?混凝土電子滑移傳感器，並分別在型鋼翼緣、腹板和混凝土上布置了電子應變片，對試驗柱在受荷全過程的受力性能、和內部滑移的變化進行了細致的觀察。After description of slide line fields according to the different proportion of width / diameter, the stress function in flat plate upsetting has been determined, the changing rule of slide line fields been described, the process of column upsetting been simulated by using the software of abaqus and the theoretical value been proved through comparing the simulation value with the theoretical value
摘要本文應用滑移線理論來求解平板鐓粗模型，描述了在不同寬徑比下的滑移線場，確立該模型單元的應力場表達式，描述其滑移線場的變化規律，最後運用abaqus軟體對圓柱體鐓粗進行數值模擬，將模擬值與理論值進行對比，對理論值進行驗證。Holders for sliding guide die sets of fine blanking die with fixed punch. shroud rings for pressure plate of center pillar set
精沖模固定凸模式滑動導向模座.中間導柱活動模板Based on the reasonable model of bond - slip, theoretical calculating about slip and slip strain was done. and then the influence of it between steel shape flange and concrete on stiffness deflection of eccentric loading columns was conducted and a simple calculating formula about stiffness of eccentric loading columns was built
在建立合理的粘結滑移模型的基礎上，對型鋼與混凝土的滑移，及滑移應變進行了理西安建築科技大學博士學位論文論計算，並進一步推導出型鋼與混凝土的滑移效應對偏壓柱剛度、變形的影響程度，建立了簡化的偏壓柱剛度計算公式。Sliding guide die sets of fine blanking die with fixed punch. center pillar sets
精沖模固定凸模式滑動導向模架.中間導柱模架分享友人